• International Journal of Highway Engineering
• /
• v.13 no.2
• /
• pp.139-145
• /
• 2011

The practice of asphalt pavement recycling has grown rapidly over the decade, one of which is the cold in-place recycling with the foamed asphalt (CIR-foam) or the emulsified asphalt (CIR-emulsion). Particularly, in Iowa, the CIR has been widely used in rehabilitating the rural highways because it significantly increases the service life of the existing pavement. The CIR layer is typically overlaid by the hot mix asphalt (HMA) to protect it from water ingress and traffic load and obtain the required pavement structure and texture. Most public agencies have different curing requirements based on the number of curing days or the maximum moisture contents for the CIR before placing the overlay. The main objective of this study is to develop a moisture loss index that the public agency can use to monitor the moisture content of CIR layers in preparation for a timely placement of the wearing surface. First, the moisture contents were measured in the field using a portable time domain reflectometry (TDR) device. Second, the weather information in terms of rain fall, air temperature, humidity and wind speed was collected from the same location. Finally, a moisture loss index was developed as a function of initial moisture content, air temperature, humidity and wind speed. The developed moisture loss index based on the field measurements would help the public agency to determine an optimum timing of an overlay placement without continually measuring moisture conditions in the field.

• Journal of Soil and Groundwater Environment
• /
• v.12 no.2
• /
• pp.1-8
• /
• 2007

A series of batch and column experiments were conducted for the development of biobarrier technology which can be applied to containment and reduction of contaminants in soil and ground waters. The growth kinetic constants of Pseudomonas fluorescens on glucose or molasses were determined using batch experiments. The maximum specific growth rate (Vmax) of P. fluorescens at $23^{\circ}C$ on glucose or molasses were $0.246\;hr^{-1}$ and $0.073\;hr^{-1}$, respectively. However, molasses was selected as carbon source due largely to the absence of lag phase of P. fluorescens growth on molasses and economic reason. In constant head column experiments, the hydraulic conductivity of the column soil reduced by $6.8{\times}10^{-3}$ times from $4.1{\times}10^{-2}cm/sec$ to $2.8{\times}10^{-4}cm/sec$ after the inoculation of P. fluorescens and administration of carbon source and nutrients. The biomass concentration was observed highest in the column inlet. Measurements of carbon source and electron accepter (dissolved oxygen) concentration showed that the growth of P. fluorescence, which is the main reason for hydraulic conductivity reduction, was limited not by the concentration of carbon source but by the concentration of electron acceptor.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.2
• /
• pp.113-119
• /
• 2015

This study examined remediation of soil contaminated with polychlorinated biphenyls (PCBs) and other persistent organic pollutants by using subcritical water. Our results showed that removal efficiency of PCBs from soil and treatment temperature were linearly proportional under subcritical conditions. The removal efficiency as increased as reacting period increased. PCBs contaminating fine particles in soil were less effectively removed than those in entire contaminated soil. Reaction of the zero-valent iron and PCBs under subcritical condition produced dechlorinated product, where most of the PCBs were oxidised while little remained as dechlorinated. Other organic pollutants, such as TPH, BTEX, TCE/PCE, and chlorpyrifos, were removed by more than 90% at $300^{\circ}C$. Considering removal efficiency and identification of by-products, we suggest that subcritical water treatment may be effectively applied to soils contaminated with various persistent organic pollutants.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.307-307
• /
• 2010

최근 유한연료의 고갈로 인해 세계 유가가 불안정 됨으로서 대체 에너지에 대한 연구가 많이 진행 되고 있다. 특히 압전 소자를 이용한 에너지 하베스팅은 압전 역효과를 이용한 것으로서 주변에서 무의미하게 버려지는 진동이나 바람, 열 에너지를 실 생활에 사용할 수 있는 전기 에너지로 변환할 수 있는 유망한 기술 중 하나이다. 이러한 에너지 하베스팅 기술은 일본과 같은 선진국에서 이미 지하철 및 일반 다리와 같이 진동이 극히 많은 곳에서 응용되고 있다. 이러한 에너지 하베스팅 기술을 응용 하려면 전압출력 계수($g_{33}$)가 높아야 한다. 이것은 압전 d 상수와 유전상수에 영향을 많이 받는 것으로 알려져 있다. 현재가지 응용되는 압전 하베스팅 조성은 Pb(Zr,Ti)$O_3$ (PZT)를 기초로한 세라믹이 응용되고 있다. Pb(Zr,Ti)$O_3$ (PZT) 세라믹은 Morpohotropic phase boundary(MPB)에서 전기기계 결합계수 (kp) 와 기계적 품질계수 (Qm) 이 각각 0.5와 500으로 우수한 특성을 나타낸다. 또한 큐리온도 (Tc) 도 $400^{\circ}C$로 온도 안정성 또한 높다. 하지만 $1000^{\circ}C$ 이상에서 소결하는 PbO는 소결 중 급격한 휘발로 환경적 오염 뿐 아니라 특성의 저하를 야기시킨다. 그래서 몇몇 나라에서는 그 사용을 제한하고 점차적으로 사용을 줄여 나가고 있는 동시에 PbO가 첨가되어 있지 않은 Lead-Free 세라믹의 연구가 많이 진행되고 있다. Lead-Free 세라믹 중 alkaline niobate를 기초로 한 페로브스카이트 구조의 ($Na_{0.5}K_{0.5})NbO_3$ (NKN) 은 PbO를 기초로 한 세라믹을 대체할 유망한 후보자 중 하나이다. 하지만 NKN세라믹의 K 성분의 조해성 및 고온에서의 휘발로 인해 일반 적인 소결 방법으로는 고밀도의 세라믹을 얻기 매우 어렵다. 그래서 Hot pressing, Hot forging, RTGG(Reactive Template Grain Growth), SPS(Spark plasma Sintering)와 같은 특별한 소결 법을 이용하거나 $K_8CuNb_4O_{23}$(KCN) 이나 $K_{5.4}Cu_{1.3}Ta_{10}O_{29}$(KCT) 등을 첨가하여 그 소결성을 향상 시키는 방법도 있다. 또한 압전 d상수를 향상 시키기 위해 $Nb_2O_5$나, $La_2CO_3$, $CeO_2$, $Li_2CO_3$ 등을 치환함으로써 압전 d상수를 향상 시켜 전압출력 계수를 높이는 연구 또한 많은 보고가 되어 있다. 특히 $Li_2CO_3$의 첨가는 일반 적인 소결 방법으로도 밀도의 조밀함을 향상 시켜 그에 따른 높은 유전율과 전기기계 결합계수, 압전 d상수를 가져 많은 연구가 되어지고 있다. 그래서 본 연구에서는 일반적인 ($K_{0.5}N_{0.5})_{1-x}Li_x(Nb_{0.96}Sb_{0.04})O_3$ + 0.2mol%$La_2O_3$ + 1.2mol%$K_8CuNb_4O_{23}$ 세라믹에 x(=Li) 치환에 따른 유전 및 압전특성을 조사하였다.

• Korean Journal of Poultry Science
• /
• v.17 no.4
• /
• pp.255-268
• /
• 1990

This study was carried out to investigate the time-trends of genetic parameters of the dosed flock population which selected for improving egg production. Data for two layer pure lines, Line-W (Single Comb White Leghorn) and Line-B (brown layer) which have been maintained at the Mani Breeding Farm were collected from 1980 to 1985 during 5 generations. The effective number of parents per generation ranged from 148 to 366 in Line-W and 85 to 355 in Line-B, and the cumulative expected inbreeding coefficients during 5 generations of selection were 15％ and 1.6％. So inbreeding could not be considered a critical factor on estimating the genetic parameters, heritabilities and genetic correlations Heritabilities of EN 300 and EN 400, primary two selected traits were significantly decreased during 5 generations but the estimates of the other 03its not showed the consistent decreasing pattern significantly. No time trends of probable consequence were evident in the genetic correlation coefficients of the traits studied. The reason for that situation was attributed to the fact that selection was conducted for multiple objectives and the relative importance of selection for the studied traits were not consistent by generations.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.4
• /
• pp.31-39
• /
• 2020

Shear wave velocity (or shear modulus) is very important in the evaluation of seismic performance of a fill dam under an earthquake. A shear wave velocity profile can be determined by surface wave method such as HWAW and SASW methods but this profile has uncertainty caused by spatial variation of material property in a fill dam. This uncertainty in shear wave velocity profile could be considered using a coefficient of variation of material property in the reliability based analysis. In this paper, the possible 600 shear wave velocity profiles in the core and rockfill zone of fill dam were generated by the random shear wave velocity profile generation method, proposed by Hwang and Park, based on the field shear wave velocity profiles determined by the HWAW and SASW methods. And, through the statistical analysis of generated shear wave velocity profiles in the fill dam, the coefficient of variation (COV) of shear wave velocity with depth were evaluated for the core and rock filled zone of fill dam in Korea.

• Proceedings of the Korean Information Science Society Conference
• /
• 2004.10b
• /
• pp.106-108
• /
• 2004

이미지의 유사도나 의미분석을 위해 주요 특징벡터인 색상, 경계선, 질감 등의 연구와 이들을 이미지 전역구간 및 관심영역에 적용하기 위해 데이터베이스에 저장하기 위한 연구가 활발히 진행되고 있다. 특히, 특징벡터의 분할 방법을 유동적, 또는 크게 할 경우 알고리즘 복잡화로 인해 추출 및 검색시간과 오버헤드가 증가하게 되고, 적게할 경우 정확도가 감소한다. 따라서 본 논문은 색상 및 경계선 벡터를 사분트리 분할 인덱스 구조로 데이터 베이스에 저장하고, 두 가지 문제를 동시에 해결하기 위한 방법을 제안한다. 이미지 전역구간을 사분노드로 분할하고, 관심영역의 색상정보를 비교하고, 추출된 전역적 경계분포 순위계수와 비교 알고리즘을 이용하여 이미지에 분포된 객체의 위치정보를 검색함으로써, 검색속도 및 정확성을 개선하였다

• Journal of Advanced Navigation Technology
• /
• v.14 no.3
• /
• pp.375-383
• /
• 2010

In this paper, the correlation between voice vowels and human body is analysed for the voice therapy and diagnosis. Using vowels('a', 'e', 'i', 'o', 'u'), the vibration signals in head, chest and belly is measured with the voice signal. As the result, it is shown that body characteristics can be checked from some vowels, and the correlation coefficient of body vibration signal and BMI(body mass index) is computed. From the result, using voice signal and body vibrations, the body diagnosis model is proposed.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.4
• /
• pp.363-370
• /
• 2000

Experiments have been peformed, using pure refrigerant R134a and a zeotropic refrigerant mixture R290/R600a(60%/40%) and their performances have been analyzed by the first and second laws(exergy method) of thermodynamics. From the experimental results, variations of compressor speed and air temperature have a great effect on the performance of the system. The sum of exergy losses in compressor and evaporator is about 60% of total exergy loss, using refrigerant R134a, so it is necessary to improve the performance of compressor and evaporator. According to the experimental results using refrigerant mixture of R290/R600a(60%/40%), the exergy losses in heat exchange processes are decreased but the exergy loss in throttling process is increased. The performance of the system has been improved by 20∼30% compared with that of R134a and exergy losses have been also reduced.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2002.05a
• /
• pp.81-84
• /
• 2002

Recently Bentonite mat is applied various structure : External waterproofing for underground structure, A reclaimed land, Artificial lake, Large-scaled civil structure, etc. With these various structure environment, water quality for application of Bentonite Mat affects watertightness. Specially spot with a large quantity of Chloride ion like salt water, degree of watertightness revelation is evaluated and applied. In this study, it is a main goal to investigate watertightness of Bentonite Mat with distilled water and salt water dissolved chloride ion Contents 0.88%. The result of this paper is as follows. 1) Water permeability coefficient of Bentonite Mat : distilled water(1.21$\times$10$^{-9}$cm/sec), salt water(3.12$\times$10$^{-7}$cm/sec). 2) Variation of thickness : distilled water(187%), salt water(108%). 3) Swelling ratio : distilled water(1500%), salt water(350%).