• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.17 no.3
• /
• pp.149-157
• /
• 2005

Typical water quality (WQ) parameters defined in the governing equation of the WQ model are the pollutant loads from atmosphere and watersheds, pollutant release rates from sediment, diffusion coefficient and reaction coefficient etc. The direct measurement of these parameters is very difficult as well as requires high cost. In this study, the pollutant budget equation including these parameters was used to construct the linear simultaneous equations. Based on these equations, the inverse problems were constructed and WQ parameter estimation method minimizing the sum of squared errors between the computed and observed amounts of the mass changes was suggested. WQ parameters, i.e., the atmospheric pollutant loads, sediment release rates, diffusion coefficients and reaction coefficient, were estimated using .this method by utilizing the vertical concentration profile data which has been observed in Cheonsu Bay and Ulsan Port. Values of the estimated parameters show a large temporal variation. However, this technique is persuasive in that the RHS (root mean square) error was less than $5.0\%$ of the observed value ranges and the agreement index was greater than 0.95.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.10a
• /
• pp.335-341
• /
• 1997

운전중 노심의 출력변화를 감시하는 노외계측기(Excore Detector)는 노내계측기(Incore Detector)를 통하여 측정되어진 축방향 출력편차(Axial Offset)를 이용하여 교정되고 있다. 노외 계측기의 전류와 축방향출력편차의 선형적인 관계를 가정하여 노내계측기로 최소한 4회 노심출력을 측정한후 최소자승법(Least Square Method)으로 비례상수들을 구하는 기존의 방법을 대신하여, 단순 노외계측기 교정법은 노내계측기로 1회 측정되어진 자료들을 이용하여 계측기 반응상수(Detector Response Factor)를 계산한 후 비례상수를 계산한다. 계측기반응상수는 2차원 중성자수송모델로부터 계산된 weighting factor와 3차원 확산이론으로부터 구한 노심출력을 이용하여 계산된다. 중성자수송계산은 (R-Z)와 (R-$ heta$)모델을 합성하여 3차원 weighting factor를 계산하므로 축방향 영향뿐만 아니라 집합체별 영향을 고려하였다. 또한 노심의 복잡한 구조로 인하여 근사적인 weighting (actor와 노심출력분포의 사용은 노외계측기의 전류와 계측기반응율의 불일치를 초래하며, 이를 해결하는 상수를 소개하여 보다 정확한 교정결과를 얻도록하였다. 이와 같은 방법을 고리 3호기 9, 10주기 전주기와 11주기초에 적용하여 노심의 연소분포, 냉각수의 온도분포, 노심의 연소도, 노심출력준위등에 대한 단순 노외계측기 교정법의 오차를 분석하여 최적의 노외계측기 교정모델을 제시하였다. 2차원 중성자수송모델 합성법에 의한 단순노외계측기 교정법은 2차원 (R-Z) 중성자수송모델보다 개선된 결과와 평균오차 0.179% 최대 오차 0.624%를 보여주고 있다.하면 조사 후의 조직안정성에도 크게 기여할 것으로 기대된다.EX>O가 각각 첨가된 경우, Ar-4vol.%H$_2$ 분위기보다 H$_2$분위기에서 소결했을 때 밀도가 더 높았다. 그러나, 결정립은 $UO_2$와 $UO_2$-Li$_2$O의 경우, 수소분위기에서 소결했을 때, (U,Ce)O$_2$와 (U,Ce)O$_2$-Li$_2$O에서는 Ar-4vol.%H$_2$분위기에서 소결했을 때 더욱 성장하였다.설명해 줄 수 있다. 넷째, 불규칙적이며 종잡기 힘들고 단편적인 것으로만 보이던 중간언어도 일정한 체계 속에서 변화한다는 사실을 알 수 있다. 다섯째, 종전의 오류 분석에서는 지나치게 모국어의 영향만 강조하고 다른 요인들에 대해서는 다분히 추상적인 언급으로 끝났지만 이 분석을 통 해서 배경어, 목표어, 특히 중간규칙의 역할이 괄목할 만한 것임을 가시적으로 관찰할 수 있 다. 이와 같은 오류분석 방법은 학습자의 모국어 및 관련 외국어의 음운규칙만 알면 어느 학습대상 외국어에라도 적용할 수 있는 보편성을 지니는 것으로 사료된다.없다. 그렇다면 겹의문사를 [-wh]의리를 지 닌 의문사의 병렬로 분석할 수 없다. 예를 들어 누구누구를 [주구-이-ν가] [누구누구-이- ν가]로부터 생성되었다고 볼 수 없다. 그러므로 [-wh] 겹의문사는 복수 의미를 지닐 수 없 다. 그러면 단수 의미는 어떻게 생성되는가\ulcorner 본 논문에서는 표면적 형태에도 불구하고 [-wh]의미의 겹의문사는 병렬적 관계의 합성어가 아니라 내부구조를 지

• Journal of KIISE:Software and Applications
• /
• v.33 no.4
• /
• pp.402-410
• /
• 2006

This paper presents a method for feature based block motion estimation that uses multi -resolution image sequences to obtain the panoramic images in the continuous ultrasound image sequences. In the conventional block motion estimation method, the centers of motion estimation blocks are set at the predetermined and equally spaced locations. This requires the large blocks to include at least one feature, which inevitably requires long estimation time. In this paper, we propose an adaptive method which locates the center of the motion estimation blocks at the feature points. This make it possible to reduce the block size while keeping the motion estimation accuracy The Harris-Stephen corner detector is used to get the feature points. The comer points tend to group together, which cause the error in the global motion estimation. In order to distribute the feature points as evenly as Possible, the image is firstly divided into regular subregions, and a strongest corner point is selected as a feature in each subregion. The ultrasound Images contain speckle patterns and noise. In order to reduce the noise artifact and reduce the computational time, the proposed method use the multi-resolution image sequences. The first algorithm estimates the motion in the smoothed low resolution image, and the estimated motion is prolongated to the next higher resolution image. By this way the size of search region can be reduced in the higher resolution image. Experiments were performed on three types of ultrasound image sequences. These were shown that the proposed method reduces both the computational time (from 77ms to 44ms) and the displaced frame difference (from 66.02 to 58.08).

• Journal of Environmental Impact Assessment
• /
• v.31 no.5
• /
• pp.271-285
• /
• 2022

The AERMET, the AERMOD meteorological preprocessing program, mainly used for environmental impact assessment and Integrated Environmental Permit System (IEPS) in Korea, has not considered the land covers characterasitics, and used only the past meteorological data format CD-144. In this study, two results of AERMET application considering CD-144 format and ISHD format, being used internationally, were compared. Also, the atmospheric dispersion characteristics were analyzed with consideration of land cover. In the case of considered the CD-144 format, the actual wind speed was not taken into account in the weak wind (0.6~0.9m/s) and other wind speed due to the unit conversion problem. The predicted concentration considering land cover data was up to 387% larger depending on the topographic and emission conditions than without consideration of land cover. In conclusion, when using meteorological preprocessing program in AERMOD modelling, AERMET, with ISHD format, land cover characterasitics in the area should be considered.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.1
• /
• pp.24-29
• /
• 2004

In ocean acoustic tomography (OAT), the pulse compression techniques using M-sequences are employed in the many studies for investigating the ocean structures. M-sequences can provide the good time and Doppler resolution in the process of demodulation using matched-filter. The signal-to-noise (SNR) performance at the output of receiver may be improved by manipulating received signal, i. e. coherently averaging. The processing time can be significantly reduced by using fast hadarmard transform (FHT) or fast Fourier transform (FFT). In this paper, we estimate the multipath arrival structures and delay times using the East Korean Sea experiment data and explore the compensation method for the detrimental effects on performance due to sampling rate error. We also analyze the characteristics of the ocean acoustic channels through scattering function, delay power profile, and time dispersions.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.1
• /
• pp.265-276
• /
• 2018

Observation and data analysis techniques have been developed for observational blind areas in the lower atmosphere that are difficult to be monitored with fixed equipment on the ground. The vertical data of temperature and relative humidity are remotely collected by the UHF radiosonde installed on UAV and compared with the data measured in the 10 m weather tower. From the validated vertical profile, extrapolated surface temperature and the bulk transfer method were used to estimate the sensible heat flux depending on the atmospheric stability. Compared with the sensible heat flux measured by the 3-dimensional ultrasonic anemometer on the ground, the error of the sensible heat flux estimated was 23% that is less than the range of 30% allowed in the remote sensing. Estimated atmospheric boundary layer height from UAV sensible heat fluxes can provide useful data for air pollution diffusion models in real time and economically.

• Journal of Digital Convergence
• /
• v.12 no.11
• /
• pp.273-279
• /
• 2014

In this paper, we propose a novel algorithm for three dimensional positioning system and implement a system over indoor wireless channel. A commercial modules are used for mobile and fixed nodes which are product of German company Nanotron Co. This module adopts chirp spread spreading scheme as modulation method to improve the ranging resolution and the module satisfies the IEEE standard 802.15.4a. The distance computation is based on received signal strength(RSS) levels and trilateration method. A testbed was set up to measure and compare the positioning estimation error of the proposed algorithm. The experiments results showed that the accuracy of location estimation was sufficiently good as much as 1m distance error in a wireless environment in an office building.

• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.747-754
• /
• 2009

In this study, adsorption isotherms of o-DCB(ortho-dichlorobenzene) on an activated carbon heated at $1000^{\circ}C$ for 24 hours were obtained by experiment and were predicted by using molecular simulation. The initial molecular structure of the activated carbon was designed on the basis of its molecular formula and functional groups ratio measured experimentally. Then, the molecular structure was optimized using the COMPASS(condensed-phase optimized molecular potentials for atomistic simulation studies) force field. The particle porosity, specific surface area, and particle density obtained from the optimized molecular structure of activated carbon were compared with those experimental data. The errors between experimental data and simulation results of the particle porosity, specific surface area, and particle density were shown as 7.6, 3.8, and 2.8%, respectively. Adsorption isotherms constants of o-DCB are calculated by the GCMC(grand canonical Monte Carlo) method in the optimized molecular structure of activated carbon. The simulation result of the adsorption isotherms showed an error of under 3%, compared to that of experimental data. Adsorption isotherms, adsorption heat and pore diffusivity of 2,3,7,8-TCDD(tetrachlorodibenzo-p-dioxin) was finally obtained in the same molecular structure of the activated carbon as used for o-DCB. Thus, adsorption characteristics of persistent organic pollutants on activated carbon, which are not easy to experimentally evaluate, are predicted by the molecular simulation.

• Journal of Korean Society for Geospatial Information Science
• /
• v.24 no.1
• /
• pp.81-87
• /
• 2016

It is important to analyze the exact damage information for fast recovery when natural disasters cause damage on river-side facilities such as dams, bridges, embankments etc. In this study, we shows the method to effectively damage analysis plan using UAV(Unmanned aerial vehicle) images and accuracy assessment of it. The UAV images are captured on area near the river-side facilities and the core methodology for damage analysis are image matching and change detection algorithm. The result(point cloud) from image matching is to construct 3-dimensional data using by 2-dimensional images, it extracts damage areas by comparing the height values on same area with reference data. The results are tested absolute locational precision compared by post-processed aerial LiDAR data named reference data. The assessment analysis test shows our matching results 10-20 centimeter level precision if external orientation parameters are very accurate. This study shows suggested method is very useful for damage analysis in a large size structure like river-side facilities. But the complexity building can't apply this method, it need to the other method for damage analysis.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2009.11a
• /
• pp.363-366
• /
• 2009

변이영상은 두 스테레오 영상의 시차에 의해 발생하는 각 화소의 변위를 수록한 영상이다. 이 영상은 깊이영상을 생성하여 시점 간 가상영상을 생성하는데 사용된다. 따라서 변이영상은 다시점 비디오 서비스와 직접적인 연관이 있다. 본 논문에서는 유일성(uniqueness)제약과 순차성(ordering) 제약을 사용하여 기준영상과 참조영상 사이의 관계를 이용하여 생성한 변이 공간 영상(DSI : disparity space image)으로부터 비용 행렬을 계산하여 최적의 변이 경로를 찾아가는 다이내믹 프로그래밍을 분석 하였다. 다이내믹 프로그래밍은 정밀한 변이 맵을 얻을 수 있고, 다른 방식들에 비해 연산 속도가 빠르다는 장점을 가지고 있지만, 영상의 화소값의 변화가 없는 영역에서 이전의 경로를 계속 유지하려는 성질에 때문에 발생 하는 오류확산과 가려진 (occluded) 영역에 의한 오차로 인해 정확한 경로를 찾을 수 없는 경우가 빈번히 발생 하여 에러율이 높아지는 단점을 가지고 있다. 이러한 이론을 토대로 기존의 기법들에 비하여 정확도가 우수한 기법들을 제안하였다. 개선된 역 추적 과정을 이용하여 기존의 다이내믹 프로그래밍 기반의 스테레오 정합 기법들보다 우수성이 뛰어난 결과들을 나타내었다.