• Membrane Journal
• /
• v.8 no.3
• /
• pp.130-137
• /
• 1998

Membrane fouling characteristics in the membrane-coupled activated sludge system were investigated. The influence of the floc size variation on the filtration resistance was analyzed using resistance-in-series model and mixed liquor was fractionated into three components to verify which component would give rise to a major contribution to the total resistance. The microbial floc size was rapidly reduced during the initial 4~6 hours of operation, and then decreased slightly but steadily, followed by leveling off at the size of 20 $\mu$m. The specific resistance of activated sludge increased with operation time, and measured values of specific resistance were matched well with the values estimated on the basis of the mean particle size in the mixed liquor. The contribution of soluble organics and cells to the total resistance was relativdy small compared with that of the supematant. Colloidal particles in the supematant showed much higher specific resistance than that of microbial floc, and played the most important role in the cake resistance.

• Analytical Science and Technology
• /
• v.17 no.6
• /
• pp.514-519
• /
• 2004

Soil samples collected from around the BOMARC Missile Site were measured for their activity concentrations and isotopic ratios of Pu and Am isotopes with particle sizes. The activity concentrations of Pu and Am in the BOMARC soil were remarkably higher than the fallout levels, and the activities decreased nearly exponentially with an increasing particle size of the soil due to a decreasing surface area. The activity ratios of Pu-238 / Pu-239, 240, Pu-241 / Pu-239, 240 and Am-241 / Pu-239, 240 observed in the BOMARC soil were much lower than those attributed to the nuclear reprocess plants and the Chernobyl fallout. Also, the atomic ratio of Pu-240 / Pu-239 in the BOMARC soil was remarkably lower than the fallout value influenced by the nuclear weapons testing and the Chernobyl accident. The atomic ratio of Pu-240 / Pu-239 was so close to the value of the weapons grade Pu released from the crash of a B52 plane in the Thule of the Greenland, such that the Pu isotopes detected in the BOMARC soil could have originated from the weapons grade plutonium.

• Applied Chemistry for Engineering
• /
• v.8 no.4
• /
• pp.624-630
• /
• 1997

Zeolite A helps an increase of detergency performance according to showing the ion exchange effect for polyvalant ions and it's detergency performance could be calculated quantitatively by using the disperse stabilization theory because it is water-insoluble material and is as colloid particles in aqueous solution. In this study, zeta potential of carbon black, cellulose, and Zeolite A were measured in each inorganic salt solutions and applied to the theory of Heterocoagulation in order to evaluate the detergency performance of Zeolite A about the particulate soil at the view point of interaction potential energy. Zeolite A was shown help an increase of detergency performance according to the increasing of the steric repulsion between Zeolite A and cellulose in $Na2CO_3$ solution and the decrease of re-deposition of carbon black on the fabric by rapid coagulation with carbon black in $Na_2SO_4$ solution.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.286-286
• /
• 2010

최근에 환경 오염과 화석 에너지의 고갈 문제를 해결하기 위하여 태양광을 전기 에너지로 변환하는 태양전지 연구에서 가장 이슈가 되는 부분은 저가격화와 고효율이다. 상용화 되어 있는 대부분의 태양전지는 단결정 실리콘 웨이퍼와 다결정 실리콘 웨이퍼를 사용한다. 실리콘 웨이퍼의 원자재 가격을 낮추는 방법에는 한계가 있기 때문에 태양전지 제작 공정에서 공정 단가를 낮추는 방법이 많이 연구되고 있고, 실리콘 웨이퍼가 가지는 재료의 특성상 화합물을 이용한 태양전지 보다 낮은 효율을 가질 수밖에 없기 때문에 반도체 소자 공정을 응용하여 실리콘 웨이퍼 기판에서 고효율을 얻는 방법으로 연구가 진행 되고 있다. 본 연구에서는 마이크로 블라스터를 이용하여 태양전지 cell 상부에 AG(anti-glare)를 가지는 유리 기판을 형성하여 낮은 단가로 태양전지 cell의 효율을 향상시키기 위한 연구를 진행 하였다. 태양전지 cell 상부에 AG를 가지는 유리 기판을 형성하게 되면 태양의 위도가 낮아 표면에서 대부분 반사되는 태양광을 태양전지 cell에서 광기전력효과가 일어나게 하여 효율을 향상시킨다. 이때 사용한 micro blaster 공정은 고속의 입자가 재료를 타격할 때 입자의 아래에는 고압축응력이 발생하게 되고, 이 고압 축응력에 의하여 소성변형과 탄성변형이 발생된다. 이러한 변형이 발전되어 재료의 파괴 초기값보다 크게 되면 크랙이 발생되고, 점점 더 발전하게 되면 재료의 제거가 일어나는 단계로 이루어지는 기계적 건식 식각 공정 기술이라 할 수 있다. 먼저 유리 기판에 마이크로 블라스터 장비를 이용하여 AG를 형성한다. AG는 $Al_2O_3$ 파우더의 입자 크기, 분사 압력, 노즐과 기판과의 간격, 반복 횟수, 노즐 이동 속도 등의 공정 조건에 따른 유리 기판 표면에서의 광학적 특성 및 구조적 특성에 관하여 분석하였다. 일반적인 태양전지 cell 제작 공정에 따라 cell을 제작 한후 AG 유리 기판을 상부에 형성시키고 솔라시뮬레이터를 이용하여 효율을 측정하였다. 이때 솔라시뮬레이터의 광원이 고정되어 있기 때문에 태양전지 cell에 기울기를 주어 태양의 위도 변화에 대해 간접적으로 측정하였다. AG 유리 기판이 태양전지 cell 상부에 형성 되었을 때와 없을 때를 각각 비교하여 AG 유리 기판이 형성된 태양전지 cell에서의 효율 향상을 확인하였다.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.7
• /
• pp.1263-1271
• /
• 2000

This study investigated the floc structure and removal of turbidity and organic matter by alum coagulation. Results of this study indicated that sweep floc and charge neutralization area were shifted to more acidic region than that in the Amirtharajah's diagram. This was caused by organic matter present in the raw water. Removal regions of turbidity and organic matter were generally overlapped. However, organic matters was removed better at lower pH than turbidity. Floc structure was characterized by measuring fractal dimension and volume diameter using AIA and SALLS. SALLS method was found to be more reliable than AIA method. Floes in sweep floc region had larger size and fractal dimension than flocs in charge neutralization region. As pollutant removal increased, larger fractal dimension and size of floc were measured.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.2
• /
• pp.323-329
• /
• 2000

The coupling of an activated sludge reactor with a membrane unit, i.e., Membrane Coupled Activated Sludge (MCAS) system offers several advantages over conventional process. But the major hurdle in the extensive use of this process is the continuous reduction of permeation flux caused by membrane fouling. The aim of this study is to investigate membrane fouling characteristics in the MCAS process. During crossflow ultrafiltration(CFUF) of activated sludge, floc size decreased abruptly at the beginning of operation and thereafter decreased continuously and gradually. The floc size changed from 100~200 to $6{\sim}8{\mu}m$ depending on recirculation velocity. This floc breakage played a key role in rapid increase of $R_c$(cake layer resistance), which led to flux decline. The floc breakage stimulated biomass to release EPS(Extracellular Polymeric Substance) which has been known to be one of the major membrane foul-ants. The amounts of EPS before and after CFUF were 266 and 405(VS mg/MLSS g), respectively. The rise up of EPS concentration was another factor affecting flux decline in MCAS system.

• Analytical Science and Technology
• /
• v.12 no.1
• /
• pp.53-60
• /
• 1999

Dissolution properties for the 6 inorganic pollutants (As, Cd, Cu, Pb, Zn, Cr) in soils have been studied. These 6 inorganic pollutants were spiked to 3 kinds of fresh soils which were sand, clay, and loam. The dissolution properties of the prepared samples were investigated under the various extracting conditions such as extracting time, acid concentration, particle size, etc. in order to obtain basic information about the process of extraction test and improvement of related analytical methods. As the results, dissolution properties were affected mainly by acid concentration in extracting procedure and mineral composition of soils. On the other hand, extracting time, sort of acids and particle size of soils had a little influence on the dissolution properties. Cd revealed very high dissolving efficiency and As was very low in whole extracting test.

• Journal of Environmental Impact Assessment
• /
• v.28 no.2
• /
• pp.113-128
• /
• 2019

The concentration and coating thickness of black carbon (BC) were measured along with fine dust in the fall of 2018, at the Seoul Metropolitan Area Intensive Monitoring Station (SIMS). In fall, the concentration of $PM_{10}$ and $PM_{2.5}$ was $23{\pm}12.6{\mu}g/m^3$ and $12{\pm}5.8{\mu}g/m^3$, respectively, lower than that in other seasons. The BC level, measured using an Aethalometer, was $0.73{\pm}0.43{\mu}g/m^3$, while the levels of elemental carbon (EC) and refractory-BC (rBC), measured by semi-continuous carbon analyzer (SOCEC) and single particle soot photometer (SP2), were $0.34{\pm}0.18{\mu}g/m^3$ and $0.32{\pm}0.18{\mu}g/m^3$, respectively. As such, the concentration level differed according to the measurement method, but its time-series distribution and diurnal variation showed the same trends. The BC concentration at SIMS was primarily affected by automobiles with higher levels of BC during morning and evening commuting times due to increased traffic congestion. rBC, measured by SP2, had a peak concentration and coating thickness of 84 nm and 43 nm, respectively. Notably, the coating thickness had an inverse relationship with particle size.

• Economic and Environmental Geology
• /
• v.34 no.3
• /
• pp.271-281
• /
• 2001

The characteristics of the heavy metal contamination in the soils affected by the tailings of the Palbong mine have been studied. The soils in the studied area consist mostly of loam by the particle size analysis, but a little of it, located near the stream, consist of loamy sand to sandy loam, finally to loam downward. The organic contents of soils are significantly low aoom 2 percent and the pH is in acidic ranging 6.0 $\pm$ 0.1. The samples of the parent rocks, the normal soils, the tailings and the channel deposits from the studied area were chemically analysed. From the result, the heavy metal concenlration of the soils is a little Jow compared with that of the parent rocks, shows the hydrologic process of the surface and the groundwater. The contamination of the tailings from the ore mining are high in lead, copper and arsenic. In the channel deposits the concenlrations of lead and copper are abnormally high but that of arsenic is uniquely low. And most of heavy metal contamination are decreased with the distance from the mine. It is caused by the properties of the surface and the ground water during the process of the heavy metal migration. The correlation-coefficient between sand and silt contents and the concentrations of Cd, Cu and Pb are significant but the amounts of As and Hg are increased with the clay contents. The dispersion of the heavy metals with the distance shows that the concentrations of them in the soils sampled at distance of 100 m to 200 m along the stream started near the Palbong mine are extremely high compared with those from other distances. These discrepancies are significant in Cd, Cu, Pb and Hg, but low in As. All the samples contain below detection limit of Cr+6 In the present stream water the concentrations of the heavy metals are not detected. So, it is interpreted that the concentrations in the soils are caused by the activities of the mining during the operation and have been continued by the dispersion from the tailings since after the closure of the mining, especially by the surface and ground water. The concentrations are diminished with the distance from the mining site, but in the interval of 800-2000 m increases abruptly. In the soil samples counted on the dispersion direction by wind, the lowering of the concentration is relatively uniform with the distance from the mining site. So, the rapid increase of the heavy metal concentrations is presumed to have been caused by the ground-water movement. In the migration of the heavy metals, the groundwater conditions, such as pH, Eh, the contents of colloidal particles, and Mn and Fe oxides are closely involveo. Integrating with these factors, it is interpreted that the groundwater conditions which have caused the heavy metal contamination of the studied area are those that the pH is about 3 in oxidized conditions, the contents of the colloidal particles are low, and Mn and Fe oxides are not involved in the migration of the heavy metals. Meanwhile, the vegetables growing on the soils in the studied area are not affected by the contamination of the heavy metals.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.8
• /
• pp.401-406
• /
• 2020

NOx (nitrogen oxide) in the exhaust gas engines causes severe air pollution. NOx is produced under high-temperature combustion conditions. EGR (exhaust gas recirculation) is normally used to reduce the combustion temperature and NOx production. As the EGR ratio increases, the NOx level becomes low. On the other hand, an excessively high EGR ratio makes the combustion unstable resulting in other air pollution problems, such as unburned hydrocarbon and higher CO levels. In this study, the improvement of fuel droplets moving by the radiation of sonic waves was studied for the stable combustion using analytic and experimental methods. For the analytical study, the effects of the radiation of a sonic wave on the fuel droplet velocity were studied using Fluent software. The results showed that the small droplet velocity increased more under high-frequency sonic wave conditions, and the large droplet velocity increased more under low-frequency sonic wave conditions. For the experimental study, the combustion chamber was made to measure the combustion pressure under the sonic wave effect. The measured pressure was used to calculate the heat release rate in the combustion chamber. With the heat release rate data, the heat release rate increased during the initial combustion process under low-frequency sonic wave conditions.