• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.2
• /
• pp.235-243
• /
• 1998

For motor operation at low speeds and loads, torque pulsation by the cogging torque is often a source of vibration and control difficulty. In this paper, the magnetic field of a motor is calculated by finite element method. The periodic cogging torque is determined using Maxwell stress method and time stepping method, and then decomposed using fourier series expansion, The purpose of this paper is to characterize design parameters on the cogging torque and to design a permanent magnet motor with a cogging torque less vulnerable to vibration, without sacrificing the motor performance. The design parameters include stator slot width, permanent magnet slot width, airgap length and magnetization direction. A new design with a less populated frequency spectrum of the cogging torque is proposed after characterizing individual effect of design parameters. Magnet pole edge shaping, by gradually increasing the cogging torque with reduced higher harmonics.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.39-46
• /
• 1998

For permanent magnet brushless DC motors used for high speed fuel pumps, torque ripple is an important origin of vibration, acoustic noise and speed fluctuation. In this paper, the output torque profile of a PM motor with one phase energized is decomposed into the commutation torque, the reluctance torque and the armature reaction torque according to their source origins. It verifies that the output torque profile is qualitatively equivalent to the BEMF profile for low reluctance motors. This paper discusses the effect of magnet pole shaping and magnet arc length on the output torque and torque ripple. A magnet edge shaping is proposed to design a trapezoidal BEMF motor without torque ripple, with minimal sacrifice of the maximum output torque.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.4
• /
• pp.229-236
• /
• 2004

In this paper, the effect of permanent magnet overhang structure on the characteristics in Brushless DC motor has analyzed quantitatively. We classified the overhang structure as symmetric and asymmetric. 3D equivalent magnetic circuit network (EMCN) method which uses the permeance as the distributive variable is used for the efficient analysis of magnetic field. The overhang effect which increases the linkage flux at the stator is verified by comparison between overhang and no overhang structure. In addition, it is known that no load back electro motive force (EMF) is also increased due to the overhang effect. In case of asymmetric overhang structure, the ratio effect of the upper to lower overhang length on the magnetic forces is analyzed. Form the analysis results, the variation of the asymmetric overhang ratio has a significant effect on the axial magnetic force except the radial and tangential magnetic forces. The validity of the analysis results is also clarified by comparison between calculated results and measured ones such as back EMF and cogging torque.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.3
• /
• pp.97-103
• /
• 1999

This paper investigates reduction of acoustic noise and cogging torque in a BLDC motor with larger stator slot open width. Using energy method, cogging torque is analytically determined with airgap MMF function and airgap permeance function and confirmed by FEM analysis. It shows that the cogging torque is firstly governed by NL GNL BNL with the fundamental period of NL, where NL is the least common multiple of the number of slots and the number of poles, GNL, airgap permeance function and BNL, airgap MMF function. It also shows that there exist several tooth width which minimizes the cogging torque, for the motors that smaller slot open width or stator teeth notching is not available. And it proposes a teeth pairing with two different tooth width which can effectively eliminate the cogging torque and thus the acoustic noise. Experimental results show that the proposed teeth pairing reduces the cogging torque by 85% and the acoustic noise by 3.1dB.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.12
• /
• pp.36-45
• /
• 1998

In this paper, a method of on-line PI gain-tuninng is proposed for the speed control of brushless D.C. motor by investigating the pattern of input and output without estimating parameter. Proportional gain is tuned in the process to obtain a fast speed response by supplying the maximum constant input. And integral gain is appropriately tuned in the process of proportional control so that the response may be stably converged and the overshoot may be prevented. Therefore because both control and gain-tuning are executed concurrently, additional works that estimate parameters and so on aren't required in the proposed method. In the proposed method, both fast-response and overshoot problem are well solved, and it is more useful and convenient than existing auto-tuning methods in the speed control of D.C. motor. It is illustrated by simulations and experimental results that the proposed method is useful and stable.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.6
• /
• pp.21-30
• /
• 2022

This paper describes the design, manufacture, and testing of servos applicable to small tracking radars. First, Chapter 1 describes the necessity of this study. Chapter 2 describes the development of servos applicable to future tracking radars in small missile systems. Chapter 3 describes the design and test results for current control of brushed DC motors, brushless DC motors, and permanent magnet synchronous motors. And Chapter 4 describes the design and test results for speed control of the test wheel. And in Chapter 5, the results of the previous tests are summarized. In this paper, some pictures were intentionally blurred for security reasons, and the control result of test wheel was described, not the test with the developed gimbals.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.5
• /
• pp.433-441
• /
• 1999

This paper presents a S-FES(Superconducting magnetic becuing Flywheel Energy Storage System) for the p purpose of replacing battery used to store the energy. Especially, the design elements of FES, such as the b beming, wheel mateηaI, and power converter, etc., are described. The design and manufacturing techniques of t the controllable IXlwer converter are proposed to generate the sinusoidal output current in the high speed operation and to get the const빠synchronous motor with halbach cuTay of high coesive I\d-Fe-B permanent magnet is used as the driver of F FES. The proposed S-FES system shows the stable rotation characteristics at high speed range about l 10,000[rpm]. To verify the validity of proposed system, the comparative study with the conventional ball b beming s~rstem is proceeded and it is well confirmed with the result of the lower friction losses of S-FES S system.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.440-444
• /
• 2008

The 7-phase BLDC motor is possible for higher efficiency per the unit area, high power and high speed due to the increasing number of phase. Also, it can be looking forward to reduce the current ripple at a point of commutation by the increasing number of phase. Thus, a study for applications of servo system, medical and military instruments is progressing about the BLDC motor is manufactured with multi-phase, currently. This paper is used the fuzzy logic control method for speed control of 7-phase BLDC motor and this is compared with the conventional PI controller using by simulation and experimental results for verification validity of the fuzzy logic controller in this system. The 7-phase BLDC motor and controller are modeled by PSIM6.0 software of PowerSim co. in simulation and we are experimented by the test board that is composed with TMS320VC33-150 DSP controller of Texas Instruments co. and FLEX EPF6016TC144-3 of ALTERA co.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.1
• /
• pp.36-45
• /
• 1998

A simple source voltage clamped resonant link (SVCRL) inverter is proposed to clamp the DC link voltage to the input source voltage and reduce the current rating of resonant inductor. The current control of a permanent magnet synchronous motor (PMSM) using a predictive current control technique (PCCT) employing the SVCRL inverter is also investigated to overcome the disadvantage of the current regulated delta modulation (CRDM) control technique. By using the PCCT based on the discrete model of a PMSM and estimation of back EMF, the minimized current ripple with small number of switchings can be obtained. Finally, the comparative computer simulation and experimental results are given to show the usefulness of the proposed technique.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.11 no.9
• /
• pp.454-461
• /
• 2001

Acoustic noise and vibration of a BLDC motor is a coupled phenomenon between mechanical characteristics and electromagnetic origins through the motor air-gap. When a relative misalignment of rotor in the air-gap center exists on the assemblage, it is considered to influence the motor system characteristics. In this paper, the back electro motive force(BEMF) is analyzed by Finite Element Method(FEM) and verified by experiments for the SPM and IPM type motors. For magnetic field analysis, a FEM is used to account for the magnetic saturation. Using these results, the FEM is made to determine the appropriate electromagnetic field analysis in BLDC motors with rotor eccentricity ratio. A radial magnetic imbalance force of BLDC motor with rotor eccentricity is analyzed. Results demonstrate that the imbalance force is increased according to the degree of misalignment. An IPM motor, mostly chosen to realize high-speed operation, shows a worse effect on magnetic unbalanced forces and dynamic responses compared with SPM motor due to magnetic saturation when the rotor eccentricity exists.