• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.4
• /
• pp.333-340
• /
• 1990

The authors carried out a visiualizational model test by the hydrogen bubble method to examine the pattern of the fluid flow besides the simple camber type and plane type otter board in circulation water channel. The experimental conditions are velocity of flow 0.05 and 0.1m/sec, angle of attack 0$^{\circ}$~45$^{\circ}$(5$^{\circ}$step). The results obtained are as follows: 1. In the case of the simple camber type otter board located angle of attack 25$^{\circ}$, vortex at the leading edge was geneated at 1/2 of chord length. 2. Size of the vortex generated in the trailing edge was about 2~3 times larger then that of the leading edge. 3. In the case of the simple camber type otter board located angle of attack 30$^{\circ}$, separation of stream-line at leading edge was generated at 1/3 of chord length. 4. Nearest stream-line in the back side of the simple camber type otter board was bent in the direction of otter board when the angle of attack was 25$^{\circ}$ and 30$^{\circ}$, and in the case of plane type otter board was expanded outside of the flow direction. 6. Area separated of the simple camber type otter board at the angle of attack 30$^{\circ}$ was smaller then that of plane type otter board. 7. Flow speed in the back side of the simple camber type otter board was about 1.4 times faster then that in the front side, and in the case of the plane otter board about 1.2 times faster.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.3
• /
• pp.963-969
• /
• 1991

본 연구에서는 누설와류는 유동에 영향을 미치며 에너지 손실로 된다. 누설 와류에 의한 손실은 다른 원인에 의한 손실에 비교하여 그 비중이 크다. 따라서 누 설와류 특성을 이해하기 위해 설계영각(.alpha.=10.7˚)에서 절현비를 t/C=0.90와 2.71로 바꾸고, 또 절현비가 설계절현비 t/C=0.90일 경우에 영각을 설계 영각 .alpha.=10.7˚와 실 속점의 영각 .alpha.=18.9˚사이에서 바꾸어 회전익 후방의 회전유동장을 측정하여 누설와 류의 거동을 연구하였다.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.27 no.4
• /
• pp.286-292
• /
• 1991

The authors propose to use the vortex generators in order to improve of the efficiency for the cambered otter boards. The equipments and testing method of this model test was the same as the previous report. This study was tested for 6 models such as the single cambered, the V-shaped cambered and the slotted cambered otter board without and with vortex generators. The results obtained are as follows: \circled1 C sub(L) of the single cambered model otter board with vortex generators was increased about 10% in comparison with that of model without vortex generators, C sub(D) decreased 2%, and L/D increased 5~20%. \circled2 L/D of the V-shaped cambered model otter board with vortex generators was increased 10~20% in comparison with that of model without vortex generators. \circled3 C sub(L) of the two slotted cambered model otter board with vortex generators was increased about 20% within an angle of attack 25$^{\circ}$ in comparison with that of without vortex generators, C sub(D) increased 5~20%, and L/D was higher than prototype within an angle of attack 20$^{\circ}$. \circled4 The separation point of the model otter boards with vortex generators was removed back ward a little in comparison with that of the model without vortex generators. \circled5 Flow speed difference of the back side to the front side of model otter boards with vortex generators was increased a little in comparison with that of the models without vortex generators. \circled6 The size of separation zone in case of the model otter boards with vortex generators was decreased about 10% in comparison with that of the models without vortex generators.

• Journal of Navigation and Port Research
• /
• v.32 no.10
• /
• pp.771-776
• /
• 2008

The main purpose in having a control surface on a ship is to control the motion of it. It is the important element to determine the maneuvering characteristics of the ship. In this paper, the measured results has been compared with each other to predict the performance characteristics of flapped rudder's 2-dimensional section at $Re=3.0{\times}10^4$ using 2-frame grey level cross correlation PIV method. The side force of the rudder could be mainly improved by the lift force at 10 degrees angle of attack and the drag force at 20 degrees angle of attack. The separation point and boundary layer could be controlled by the change of the only flap's angle at 10 degrees angle of attack.

• Resources Recycling
• /
• v.2 no.4
• /
• pp.33-41
• /
• 1993

In recovering copper from the copper converter slag, various separation methods, such as flotation, sieving and magnetic separation had been tried. The copper converter slag used in this study was prepared in two ways, i.e. 2 hour cooled and 10 hour cooled. From the flotation of copper slag, 45% Cu concentrate is obtained and the amount of copper recovery is about 93%. Before the flotation, copper in the slag could be also pre-recovered using sieving and separation. It is also found that as the content of copper in the concentrate increa-ses, that of arsenic increase, while zinc and iron contents decrease.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.40 no.2
• /
• pp.149-154
• /
• 2004

Results of a numerical simulation of a flowing of the underwater vehicles hull with the pump-jet nozzle are presented. It was calculate velocity distributions coefficients of the lift force the longitudinal moment of the hull with the pump-jet nozzle and isolated hull for some values of angle of attack. It was shown that the area of the influence of the nozzle on the velocities distribution of the hull and character of changing of coefficients of the lift force and the longitudinal moment and their derivatives depending on angle of attack.

• Proceedings of the Korean Society of Fisheries Technology Conference
• /
• 2005.05a
• /
• pp.106-108
• /
• 2005

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2010.10a
• /
• pp.48-49
• /
• 2010

선박의 러더하부 끝단에서는 선회에 따른 와류로 인하여 선회력 및 후류유동에 변화를 초래한다. 이를 관측하기 위해 NACA단면 형상의 몰수체를 영각과 관측단면을 변화시키며 $Re=2.0{\times}10^4$에서 실험을 통한 순간유동장을 계측 후 그 영향을 조사하였다. 계측된 결과는 상호상관 PIV기법을 이용 Naca단면 끝단에서의 2차원 유동특성을 알아보기 위하여 상호 비교하였다. NACA단면은 영각변화에 따라 후류유동에 영향을 미친다. 동일유입유속에서 영각이 증가함에 따라 관찰단면이 중앙으로 갈수록 와류 규모가 확대되는 것을 관찰할 수 있었다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.4
• /
• pp.485-492
• /
• 2002

The present study is aimed to reveal macroscopic aerodynamic characteristics of two-dimensional rectangular prisms with three aspect ratios(D/H=1, 2 and 3) and six angles of attack($0^{circ}, 10^{circ}, 13.5^{circ}, 20^{circ}, 30^{circ} and 45^{\circ}$). The Reynolds number is fixed as $1\times10^4$. The SOLA-based revised finite difference method for the conservation form on irregular grid was adopted as a new numerical method. Instantaneous flow patterns at $45^{\circ}$ in case of D/H=2 and D/H=3 show larger asymmetric wake development which is closely related to the sharp decrease of drag coefficients at higher angles of attack range. Vorticity propagation into enlarged wake region is conjectured to be responsible for this phenomenon. The Strouhal number is found to be sensitive to the angle of attack at higher aspect ratios(D/H=2 and 3).

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.41 no.2
• /
• pp.113-121
• /
• 2005

How to extimate the angle of attack of a vertical V-type cambered otter board was described. A three-dimensional semi-analytic treatment of a towing cable system was applied to the field experiments of a midwater trawl obtained by the Scanmar system. Also the equilibrium condition of the horizontal component and vertical component of forces and moment around the otter board was used. When the warp length was 300m long and the towing speed was between 2.61 and 3.86 knots, the estimated angle of attack of the otter board was ranged between $24.7^{\circ}$ and $26.2^{\circ}$, though the maximum lift force was at the angle of attack $22^{\circ}$.