• The Journal of the Acoustical Society of Korea
• /
• v.22 no.7
• /
• pp.545-553
• /
• 2003

This paper is concerned with protecting piezoelectric transducers used in an ultrasonic flowmeter from the high temperature of hot fluid in a pipe by using a waveguide and with improving the propagation of ultrasonic longitudinal vibration in the waveguide. Waveguide material has been chosen for efficient insulation of heat transferred in the waveguide, and the minimum length of the waveguide for protecting piezoelectric transducer has been estimated. Forced response of the longitudinal vibration in a uniform circular rod has been obtained and the length of the waveguide has been selected for maximum amplitude. Longitudinal vibration response of a conically-tapered rod excited at a natural frequency has been obtained to confirm that wave motion is amplified as the cross-sectional size of the waveguide decreases along the axial direction. The fact that dispersion of a pulse wave in a waveguide is reduced as the cross-sectional radius is decreased has been examined theoretically and confirmed experimentally by using a single-rod waveguide. A bundle-type waveguide has proven to be a practical one through the evaluation of the wave propagation performance.

• Journal of Satellite, Information and Communications
• /
• v.5 no.2
• /
• pp.8-13
• /
• 2010

Satellite structure should be designed to accommodate and support safely the payload and equipments necessary for its own missions and to secure satellite and payloads from severe launch environments. The launch environments imposed on satellites are quasi-static accelerations, aerodynamic loads, acoustic loads and shock loads. Especially when optical payload is accommodated, satellite structure usually adopts the optical bench consisting of composite material not only to support and secure but also to guarantee good pointing stability against extreme thermal environments. This paper deals with optical bench and support structure which shall be designed to minimize the loads transferred to optical payloads from satellite.

• Journal of Adhesion and Interface
• /
• v.13 no.2
• /
• pp.64-72
• /
• 2012

Vinyl acetate/alkyl acrylate copolymers were prepared by water-born emulsion copolymerization according to the compositional change of vinyl acetate and various alkyl acrylates such as methyl acrylate (MA), ethyl acrylate (EA), and n-butyl acrylate (BA). Ammonium persulfate (APS) was used as an initiator and poly(vinyl alcohol) (PVA) was used as a protective colloid. The significant result was described as follows. The activation energy determined by an isothermal analysis in the temperature region between $100{\sim}200^{\circ}C$ of the copolymer had the order of PVAc/PMA > PVAc/PEA > PVAc/PBA. The peel strengths before and after the plasma treatment were the order of PVAc/PMA > PVAc/PEA > PVAc/PBA.

• Journal of the KSME
• /
• v.17 no.3
• /
• pp.159-162
• /
• 1977

금년에 들어와서 자동차의 수효가 급증하여 년말까지는 7만대선을 넘을 것이 예상되며, 승용차의 수출도 의외로 신장하여 상반기중에 2,000대를 수출하게 됨에 따라 정부당국은 자동차공업정책에 큰 수정을 가하고자 하고 있다. 즉 종래의 소극적인 보호육성정책에서 탈피해서 품질, 성능면에서 국제경쟁이 가능한 경제단위의 시설을 갖추도록 하고 기술도입을 적극권장하여 일부품일업제 육 성의 원칙을 이부 지양해서 필요하다면 일부품에 이 또는 삼개의 업체를 선정하여 조립업체와 계 열관계를 만들게 하고 또한 필요한 경우에는 모기업체의 자본참여나 기업합병도 권장한다. 육성 대상으로 선정된 부품업체에 대해서는 총액 약 450역원의 자금을 2,3년간에 걸쳐 지원한다는 것 이 그 골자가 될 것이다. 이를 위한 준비작업으로서의 지난 7월부터 3개월간에 걸쳐 국내기술진 으로 하여금 3개의 자동차조립회사와 부품제조업체의 거의 전부인 179개공장을 정밀조사하고 평 가분석을 실시한 바 있다.

• 기계와재료
• /
• v.21 no.4
• /
• pp.38-46
• /
• 2010

고온 고압의 부식 환경 하에서 사용할 수 있는 고내구성 재료 개발은 항공기와 선박의 추진체 및 발전기 등과 같이 고온부에서 작동하는 장치 설비의 수명 확보 및 안전성 보장을 위해 관련 산업계의 지속적인 연구 개발이 요구되고 있는 분야이다. 최근 세계 각국에서 발전소를 중심으로 한 새로운 고효율 에너지 생산 시스템화 계획이 구체화됨에 따라, 과거 한 종류의 연료 연소 방식으로부터 다양한 연료를 사용할 수 있는 시스템으로 전환함과 더불어 극심한 고온 산화 환경 변화에 유연하게 대응할 수 있는 소재 개발이 주요한 기술적 이슈로 부각되고 있다. 이와 같은 측면에서, 소재 '표면'의 기계적 열화를 극복하면서 생산 경쟁력을 갖춘 '새로운' 보호 코팅 기술은 가스 터빈 엔진 제조업체와 같은 장치 설비 제조 업체의 요소 기술 영역으로 자리매김 하고 있다.

• Korean Journal of Optics and Photonics
• /
• v.18 no.5
• /
• pp.351-361
• /
• 2007

The samples composed of a GST thin film and the protective layers of $ZnS-SiO_2$ or $Al_2O_3$ coated on c-Si substrate were prepared by using the magnetron sputtering method. Samples of three different structures were prepared, that is, i) the GST single film on c-Si substrate, ii) the GST film sandwiched by the protective $ZnS-SiO_2$ layers on c-Si substrate, and iii) the GST film sandwiched by $Al_2O_3$ protective layers on c-Si substrate. The ellipsometric constants in the temperature range from room temperature to $700^{\circ}C$ were obtained by using the in-situ ellipsometer equipped with a conventional heating chamber. The measured ellipsometric constants show strong variations versus temperature. The variation of ellipsometric constants at the temperature region higher than $300^{\circ}C$ shows different behaviors as the ambient medium is changed from in air to in vacuum or the protective layers are changed from $ZnS-SiO_2$ to $Al_2O_3$. Since the long heating time of 1-2 hours is believed to be the origin of the high temperature variation of ellipsometric constants upon the heating environment and the protective layers, a PRAM (Phase-Change Random Access Memory) recorder is introduced to reduce the heating time drastically. By using the PRAM recorder, the GST samples are heated up to $700^{\circ}C$ decomposed preventing its partial evaporation or chemical reactions with adjacent protective layers. The surface image obtained by SEM and the surface micro-roughness verified by AFM also confirmed that samples prepared by the PRAM recorder have smoother surface than the samples prepared by using the conventional heater.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.5 no.6
• /
• pp.575-580
• /
• 2010

The research which sees the wild animals back with the system for the penetration prevention, when the wild animals approaches with the infrared ray sensor which composes a proposed system to use radiation department and the solar heat which occur and to make lead in the spiral which informs a guard to application of power department and back the edge where uses the battery of the application of power department which supplies all the member and the outside minute electric current to do in order to maximize a warning utterance or a luminous effect, an utterance department and the light for a prevention and about the system which restrains the wild animals is a thing. The proposed system which sees the express highway and the national road, with region degree establishes back the same wild animals appears and disappears frequently a day and night and between in circumference and goes without question appears and disappears the penetration of the wild animals which prevents and the animal the vehicle and prevents the damage which collides, joins in and driver and is the ecosystem of natural environment protects preserves.

• Journal of the Korean Institute of Gas
• /
• v.26 no.1
• /
• pp.34-40
• /
• 2022

Gas cylinder cabinets have risks such as cylinder explosion and scattering of debris when a fire occurs. These risks are likely to cause gas spills and cause secondary damage. In order to reduce damage, it is very important to secure the fire resistance performance of the gas cylinder cabinet. In foreign countries, NFPA codes in the United States and EN-14470-2 in Europe stipulate fire resistance test standards for gas cylinder cabinets to protect internal cylinders for a certain period of time in a situation where gas cylinder cabinets are exposed to flames. However, in Korea, only internal pressure performance and airtight performance standards are specified, and the target is limited to piping, and research and regulations for the fire resistance performance of gas cylinder cabinets are insufficient compared to overseas. Therefore, in this study, finite element analysis was used to establish fire resistance standards for domestic gas cylinder cabinets. In the event of a fire, optimal conditions are derived in terms of structure and material.

• Journal of Environmental Impact Assessment
• /
• v.32 no.2
• /
• pp.72-82
• /
• 2023

The purpose of this study is to estimate the trend of ecosystem water quality regulating services in Odaesan National park of the last five years and the corresponding economic values. Recently the climate change makes increased the value of the water, it is more important to protect the source of the riverthan to purify the contaminated water. To evaluate the water quality regulating services, we calculated the difference between purification and pollution from national park and estimated the quantitative value of the water quality regulating services. As a results, the amount of the value of the water quality regulating services from 2017 to 2021 was increased from approximately BOD 128.21 kg/Day, T-P 12.11 kg/Day to BOD 161.38 kg/Day, T-P 13.24 kg/Day and the economic value also increased from 2,304 million won to 2,817 million won.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.3
• /
• pp.17-26
• /
• 2010

Pb-Sn solder is rapidly being replaced by lead-free solder for board-level interconnection in microelectronic package assemblies due to the environmental protection requirement. There is a general lack of mechanical reliability information available on the lead-free solder. In this study, thermo-mechanical behaviors of wire-bond plastic ball grid array (WB-PBGA) package assemblies are characterized by high-sensitivity moire interferometry. Experiments are conducted for two types of WB-PBGA packages that have Pb-Sn solder and lead-free solder as joint interconnections. Using real-time moire setup, fringe patterns are recorded and analyzed for several temperatures. Bending deformations of the assemblies and average strains of the solder balls are investigated and compared for the two type of WB-PBGA package assemblies. Results show that shear strain in #3 solder ball located near the chip shadow boundary is dominant for the failure of the package with Pb-Sn solder, while normal strain in #7 most outer solder ball is dominant for that with lead-free solder. It is also shown that the package with lead-free solder has much larger bending deformation and 10% larger maximum effective strain than the package with Pb-Sn solder at same temperature level.