• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.46 no.3
• /
• pp.229-235
• /
• 2001

The thermal and photometric properties of mulching materials modify the radiation and energy balance on the mulched soil surface and thereby change the soil temperature. The soil surface energy balances and soil temperatures under the mulching treatments of non-mulched control, recycled paper (RPM), and black polyethylene film (BPFM) were compared before and after the establishment of potato canopy. On August 30 in 1998 when potato was not emerged yet and solar radiation was 17.9 MJ $m^{-2}$${day}^{-1}$ , the net radiation of the soil surface was estimated as 10.(1, 2. 4, and 1.3 MJ $m^{-2}$${day}^{-1}$ under the control, BPFM, and RPM, respectively. The sensible and latent heat loss from the soil surface was 9.65 MJ $m^{-2}$${day}^{-1}$ in the control, most of the net radiation being lost through evaporation and convection, whereas it amounted only to 1.39 MJ $m^{-2}$${day}^{-1}$ in BPFM and 1.36 MJ $m^{-2}$${day}^{-1}$ in RPM. Therefore, the soil heat fluxes were 0.36 1.02, and 0.06 MJ m$^{-2}$ day$^{-1}$ under the control, BPFM and RPM, respectively. On September 27 when potato canopy was fully developed, the soil surface net radiation in the control was sharply decreased as compared to that of Aug. 30, whereas the net radiation of the mulched soil surfaces showed little changes. The soil heat flux was -0.01, 0.95, and 0.12 MJ $m^{-2}$${day}^{-1}$ at the soil surface under the control, BPFM and RPM, respectively. As the mulching treatments brought about such alteration of energy partitioning into the soil, the highest soil temperature was recorded in BPFM and the lowest in RMP without regard to potato canopy development. However, the soil temperature differences among the treatments become smaller when potato canopy were fully developed.

• Korean Journal of Soil Science and Fertilizer
• /
• v.37 no.3
• /
• pp.131-135
• /
• 2004

This study was carried out for the analysis of temperature characteristics on soil surface using soil heat flux which is one of the important parameters forming soil temperature. Soil surface temperature was estimated by using the soil temperature measured at 10 cm soil depth and the soil heat flux measured by flux plate at 5 cm soil depth. There was time lag of two hours between soil temperature and soil heat flux. Temperature changes over time showed a positive correlation with soil heat flux. Soil surface temperature was estimated by the equation using variable separation method for soil surface temperature. Arithmetic mean using temperatures measured at soil surface and 10 cm depth, and soil temperature measured at 5 cm depth were compared for accuracy of the value. To validate the regression model through this comparison, F-validation was used. Usefulness of deductive regression model was admitted because intended F-value was smaller than 0.001 and the determination coefficient was 0.968. It can be concluded that the estimated surface soil temperatures obtained by variable separation method were almost equal to the measured surface soil temperature.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.1
• /
• pp.91-98
• /
• 2010

The increasing of power and processing speed and miniaturization of central processor unit (CPU) used in electronics equipment requires better performing thermal management systems. A typical thermal management package consists of thermal interfaces, heat dissipaters, and external cooling systems. There have been a number of experimental techniques and procedures for estimating thermal conductivity of thin, compressible thermal interface material (TIM). The TIM performance is affected by many factors and thus TIM should be evaluated under specified application conditions. In compact packaging of electronic equipment the chip is interfaced with a thin heat spreader. As the package is made thinner, the coupling between heat flow through TIM and that in the heat spreader becomes stronger. Thus, a TIM characterization system for considering the heat spreader effect is proposed and demonstrated in detail in this paper. The TIM test apparatus developed based on ASTM D-5470 standard for thermal interface resistance measurement of high performance TIM, including the precise measurement of changes in in-situ materials thickness. Thermal impedances are measured and compared for different directions of heat dissipation. The measurement of the TIM under the practical conditions can thus be used as the thermal criteria for the TIM selection.

• Journal of Bio-Environment Control
• /
• v.25 no.3
• /
• pp.218-223
• /
• 2016

The calculation method of ground heat exchange in greenhouses has different ideas in each design standard, so there is a big difference in each method according to the size of greenhouses, it is necessary to establish a more accurate method that can be applied to the domestic. In order to provide basic data for the formulation of the calculation method of greenhouse heating load, we measured the soil temperature distribution and the soil heat flux in three plastic greenhouses of different size and location during the heating period. And then the calculation methods of ground heat exchange in greenhouses were reviewed. The soil temperature distributions measured in the heating greenhouse were compared with the indoor air temperature, the results showed that soil temperatures were higher than room temperature in the central part of greenhouse, and soil temperatures were lower than room temperature in the side edge of greenhouse. Therefore, it is determined that the ground heat gain in the central part of greenhouse and the perimeter heat loss in the side edge of greenhouse are occurred, there is a difference depending on the size of greenhouse. Introducing the concept of heat loss through the perimeter of building and modified to reflect the size of greenhouse, the calculation method of ground heat exchange in greenhouses is considered appropriate. It was confirmed that the floor heat loss measured by using soil heat flux sensors increased linearly in proportion to the temperature difference between indoor and outdoor. We derived the reference temperature difference which change the direction of ground heat flow and the perimeter heat loss factor from the measured heat flux results. In the heating design of domestic greenhouses, reference temperature differences are proposed to apply $12.5{\sim}15^{\circ}C$ in small greenhouses and around $10^{\circ}C$ in large greenhouses. Perimeter heat loss factors are proposed to apply $2.5{\sim}5.0W{\cdot}m^{-1}{\cdot}K^{-1}$ in small greenhouses and $7.5{\sim}10W{\cdot}m^{-1}{\cdot}K^{-1}$ in large greenhouses as design standard data.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.489-492
• /
• 2002

The objective of the present study were to measure the viscosities of non-Newtonian fluids by the transient flow concept in a capillary tube and to apply to hemodynamic studies and pump performance evaluations. The developed capillary tube viscometer could be used to measure the viscosities of the non-Newtonian fluids for a wide range of the shear rate by a run of experiment in a very short time interval. The measured viscosities of water and blood fur different shear rates were good agreement with those of the well established data. The measured viscosities for muddy water varied with the shear rates.

• Journal of the KSME
• /
• v.26 no.1
• /
• pp.53-57
• /
• 1986

UMIST (University of Manchester Institute of Science and Technology)는 영국의 Manchester에 있는 이공계 교육연구기관으로 약 200년의 역사를 가지고 있으며, 유명한 Reynolds의 실험이 행해진 곳으로 Dalton, Joule 등의 유명한 과학자들이 연구한 곳이고, 현재 에도 많은 연구가 행해지고 있으며, 산학협동연구가 활발히 진행되어 크게 실효를 거두고 있는 곳의 하나이다. UMIST 에서도 가장 활발한 연구를 진행시키고 있는 기계공학과의 열유체공 학부의 구성과 연구현황을 소개하기로 한다. 열유체공학부는 11명의 교수와 25명의 연구요원 1 5명의 기술직원 3명의 행정직원으로 구성되어 있으며 약 60명의 석, 박사 과정 학생들이 공부 하고 있다. 이곳의 연구분야를 좀더 세분해보면 (1)유체역학의 연구 (2)열전달의 연구 (3)내 연기관의 연구 (4)터어보기계의 연구로 나눌 수 있다.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1999.05a
• /
• pp.207-212
• /
• 1999

화학반응이 일어나는 고정층 반응기의 성능을 모사하고 해석하기 위해서는 반응베드의 열 및 물질전달 특성을 정확히 아는 것이 중요하다. 본 연구에서는 화학열펌프에 사용되는 금속염-팽창흑연 다공성 반응매체의 유효열전도도와 기체투과도를 측정하였다. 유효열전도도는 전이 일차원 열류기법을 이용하여 측정하였고, 기체투과도는 Darcy's law를 이용하여 측정하였다. 팽창흑연이 함유된 반응베드의 유효열전도도와 기체투과도는 흑연을 기준으로 한 겉보기밀도에 따라 각각 14.1-36.5 W/mK, 8.0x$10^{-15}$-$10^{-12}$ $m^2$의 범위에 있었다.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1999.11a
• /
• pp.181-186
• /
• 1999

화학 축열 시스템의 성능을 모사하고 이를 해석하여 시스템 성능을 최적화하기 위해서는, 반응층의 열 및 물질 전달 특성을 정확히 아는 것이 중요하다. 본 연구에서는 $Na_2$S-$H_2O$ 반응계를 사용한 화학 열펌프에 대한 연구로, $Na_2$S-팽창흑연 복합체의 열전도도와 기체 투과도를 측정하였고, 소형 시스템을 제작하여 그 성능을 평가하였다. 열전도도는 전이 일차원 열류기법을 사용하여 측정하였고, 기체 투과도는 Darcy's law를 이용하여 측정하였다. 반응층의 열전도도와 기체 투과도는 팽창흑연 지지체의 겉보기 밀도와 반응염의 함량에 따라 각각 6~48W/mㆍK, 1.1$\times$$10^{-13}$~1.0$\times$$10^{-11}$m$^2$의 범위에 있었다. 또한 소형 시스템을 구성하여 445W/kgㆍ$Na_2$S의 냉방 출력을 얻을 수 있었다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.13-14
• /
• 2022

This study investigated the effect of fly ash content on the isothermal hydration heat of cement pastes. Two different pastes with fly ash content were studied to cure at 35℃. The hydration heat flow deceleration stage of slurry was simulated and compared by Jander Equation and Ginstling-Brounshtein Equation. The results show that Jander Equation and Ginstling-Brounshtein Equation have certain defects in the modeling of the deceleration stage of the heat flow of cement fly ash paste, and the fitted curve can not describe the deceleration stage well.

• Horticultural Science & Technology
• /
• v.33 no.5
• /
• pp.647-657
• /
• 2015

To investigate a method for calculation of the heating load for environmental designs of horticultural facilities, measurements of total heating load, infiltration rate, and floor heat flux in a large-scale plastic greenhouse were analyzed comparatively with the calculation results. Effects of ground heat exchange and infiltration loss on the greenhouse heating load were examined. The ranges of the indoor and outdoor temperatures were $13.3{\pm}1.2^{\circ}C$ and $-9.4{\sim}+7.2^{\circ}C$ respectively during the experimental period. It was confirmed that the outdoor temperatures were valid in the range of the design temperatures for the greenhouse heating design in Korea. Average infiltration rate of the experimental greenhouse measured by a gas tracer method was $0.245h^{-1}$. Applying a constant ventilation heat transfer coefficient to the covering area of the greenhouse was found to have a methodological problem in the case of various sizes of greenhouses. Thus, it was considered that the method of using the volume and the infiltration rate of greenhouses was reasonable for the infiltration loss. Floor heat flux measured in the center of the greenhouse tended to increase toward negative slightly according to the differences between indoor and outdoor temperature. By contrast, floor heat flux measured at the side of the greenhouse tended to increase greatly into plus according to the temperature differences. Based on the measured results, a new calculation method for ground heat exchange was developed by adopting the concept of heat loss through the perimeter of greenhouses. The developed method coincided closely with the experimental result. Average transmission heat loss was shown to be directly proportional to the differences between indoor and outdoor temperature, but the average overall heat transfer coefficient tended to decrease. Thus, in calculating the transmission heat loss, the overall heat transfer coefficient must be selected based on design conditions. The overall heat transfer coefficient of the experimental greenhouse averaged $2.73W{\cdot}m^{-2}{\cdot}C^{-1}$, which represents a 60% heat savings rate compared with plastic greenhouses with a single covering. The total heating load included, transmission heat loss of 84.7~95.4%, infiltration loss of 4.4~9.5%, and ground heat exchange of -0.2~+6.3%. The transmission heat loss accounted for larger proportions in groups with low differences between indoor and outdoor temperature, whereas infiltration heat loss played the larger role in groups with high temperature differences. Ground heat exchange could either heighten or lessen the heating load, depending on the difference between indoor and outdoor temperature. Therefore, the selection of a reference temperature difference is important. Since infiltration loss takes on greater importance than ground heat exchange, measures for lessening the infiltration loss are required to conserve energy.