• 한국정밀공학회지
• /
• 제22권3호
• /
• pp.137-145
• /
• 2005

The present research deals with structural analysis and optimal design of the heating drum of a hot-rolling press for medium density fiberboard. Stress concentration in the journal of the heating drum is analyzed by the submodel technique of the finite element method. The fatigue life under operating conditions is analyzed and evaluated by the stress-life theory. Shape optimal design problems, to minimize the maximum stress occurring in the journal, are formulated and shape parameters of the corner fillets of the journal are defined as the design variables. The problems are solved by the numerical optimization method and optimal shapes are found. The optimal designs are shown to be reliable in terms of the maximum stress and the fatigue life.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.544-548
• /
• 2007

In general, final width of hot strip should be accomplished in this stage because width reduction of strip hardly appears during typical finishing mill. However, it is difficult to control the width of strip in the roughing mill process as the horizontal rolling of strip is subsequently performed after the vertical rolling. It is therefore important to obtain the deformation rolling direction on strip width to minimize the width spread of strip during horizontal rolling after vertical rolling. Generally there is Sizing press type and Edger-roll type. The width reduction process in sizing press has small amount of width spread compared with the edger. However, productivity by the sizing press process is much lower than those of the edger. In this study, sizing press and Edger-roll process parameters in a sheet rolling mill were set at specified values and the effect of the change in these parameters on product quality and process performance were evaluated.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.432-435
• /
• 2005

Extensive width reduction of slabs is an important technology to achieve continuous production between the steelmaking and hot rolling processes. Conventionally, a vertical roll process has been used to achieve extensive width reduction. However, it is impossible to avoid the defects such as dog-bone, fish tail and camber. The deformation behavior in the width sizing process is more favorable than that in conventional vertical rolling edger, i.e. the material better flows toward the center of slab. This study is carried out to investigate the deformation of slab by two-step sizing press. The FE-simulation is utilized to predict plastic deformation mode in compression by a sizing press of slabs far hot rolling. In this paper, the various causes of the asymmetrical rolling phenomena are mentioned for the purpose of understanding of rolling conditions. Analytical results of slab-deformation by sizing press are presented below in this study.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 추계학술대회 논문집
• /
• pp.217-218
• /
• 2007

• 대한기계학회논문집A
• /
• 제37권2호
• /
• pp.271-277
• /
• 2013

냉간압연 및 소둔공정에서의 조질압연 과정은 강종별로 적정 연신율을 부여함으로서 프레스 가공시 항복점 연신 현상을 제거해주는 중요한 공정이다. 적정 연신율 확보를 위해서는 강종별, 사이즈별 정확한 압연하중 예측이 필수이다. 열간 및 냉간압연과는 달리 조질압연에서는 2%이내의 연신율을 부과하는 공정이므로 압연하중 작용 시 롤 바이트 내 에서의 롤의 탄성변형 거동이 복잡하여 정확한 압연하중을 예측하기가 어려워 예측모델이 정립되어 있지 않다. 그럼에도 불구하고 최근 인장강도 590MPa 급 이상의 자동차용 고강도강 개발이 가속화 됨에 따라 조질압연시 정확한 압연하중의 예측은 더욱더 중요하게 되었다. 따라서 본 연구에서는 조질 압연 시 롤 바이트 내에서 롤의 변형거동이 유사하다고 알려져 있는 호일(foil)압연 이론 식을 이용해 조질 압연 시 전체 생산 강종을 대상으로 압연하중 예측 가능성에 대해 검토하였다. 그 결과 인장강도 350MPa 이상 980MPa 이하의 강종에 대해서는 non circular model 이 circular 모델보다 압연하중 예측 정도가 우수하며, 이 영역에서 압연하중 예측 모델로의 적용이 가능함을 확인하였다.

• 소성∙가공
• /
• 제14권9호통권81호
• /
• pp.791-797
• /
• 2005

Extensive width reduction of slabs is an important technology for achieving continuous production between the steelmaking and hot rolling processes. However, the vertical horizontal rolling process has many disadvantages, e.g., large width deviations and less efficient width reduction. This study was carried out to investigate the deformation of slab by sizing press with two steps die. To do it, dog-bone and camber are discussed in width sizing process considering the deformation behavior according to the deviation of anvil velocity and the deviation of initial slab temperature. In this paper, the various causes of the sizing press phenomena are mentioned for the purpose of understanding of rolling conditions. As a result, the optimal anvil shape having a minimum-forming load is obtained by FE-simulation and ANN.

• 소성∙가공
• /
• 제17권8호
• /
• pp.619-626
• /
• 2008

In this study, design methodology to determine optimal shape of the anvil in sizing press process has been proposed to minimize crop length of the AISI 1010 slab in horizontal rolling after width reduction. Shape of anvil were selected to 12 cases by design of experiment, and the dog-bone shapes and the crop length were determined by FE-analysis. Also, the anvil shape, which has minimum crop length, were determined by artificial neural network(ANN). As a result of FE-analysis, it can be seen that the crop length was increased with increasing center thickness in the dog-bone shape after width reduction. The anvil shape which has minimum crop length, was estimated to ${\theta}_{1}=21^{\circ}{\theta}_{2}=14^{\circ}$ by FE-analysis and ANN.