• Composites Research
• /
• v.37 no.3
• /
• pp.186-189
• /
• 2024

This study compared and evaluated the mechanical properties of carbon fiber reinforced thermoplastic polymer (CFRTP) mixed with nanofillers. After mixing various nanofillers such as Multi-wall carbon nanotube (MWCNT), Silicon oxide, Core shell rubber, and Aramid nanofiber with Polyamide 6 (PA6) resin, this is used as a matrix to create a carbon fiber reinforced composite material (CFRP) was manufactured and its physical properties were measured. Depending on the type and mixing ratio of nanofiller, tensile strength, inter-laminar shear strength (ILSS), and Izod impact strength were measured. In terms of tensile strength and impact strength, the highest values were obtained when mixing core shell rubber, however the ILSS was optimal when mixing less than 1 wt.% of silicon oxide.

• Composites Research
• /
• v.37 no.2
• /
• pp.68-75
• /
• 2024

Polypropylene (PP), a thermoplastic resin with excellent mechanical, thermal, chemical, and water resistance properties, has been attracting attention due to its economic efficiency and recyclability. However, repeated processing of thermoplastic resins can lead to property degradation, and the point at which quality degradation occurs varies depending on the processing conditions. In this study, we evaluated the performance changes of composite materials with repeated processing by blending PP resin with various additives and conducting extrusion and injection processes repeatedly. In addition, we evaluated the mechanical properties of composite materials to evaluate the effect of MFI value change during repeated processing on fiber impregnation in composite material processing.

• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.1008-1013
• /
• 1999

Mechanical properties and morphology of pectin/starch blend films depending upon the composition and plasticizer ratio were studied. Blends were prepared continuously in a twin-screw extruder. Films were prepared using a single-screw extruder with slit die. Most of the blends showed a good thermoplastic behavior, while the blends with very high ratio of pectin/starch had a poor thermoplasticity. Tensile properties of blend films were changed significantly by the amount of glycerol and relatively little by the ratio of pectin/starch. Differential scanning calorimetry(DSC) curves of wet blends showed a transition similar to glass transition temperature(Tg) at about $125^{\circ}C$. It was found by Scanning electron microscopy(SEM) study that there exists a good interfacial adhesion between pectin and starch.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.04a
• /
• pp.116-119
• /
• 2000

본 연구에서는 온도의 상승에 의하여 부피가 팽창하는 열팽창 고무 치공구의 팽창 특성을 이용하여 열경화성 복합재료를 경화하고 압축하는 과정을 실험과 모델링을 통하여 해석하였으며, 열가소성 복합재료의 함침공정을 연구하였다. 열팽창 고무치공구가 사용되는 닫힌계와 열린계에서 예상되는 압력을 이론적으로 유도하였고, 경화가 수반되는 과정에 있어서는 실험을 통하여 열팽창치공구와 프리프레그가 나타내는 압력을 측정하였다. 온도가 상승하고 경화가 수반되는 경우에 등속도 압축실험에 의하여 얻어지는 응력-변형율 곡선은 비선형점탄성 특성을 보여주었는데, 본 연구에서는 Maxwell모델을 KWW(Kohlrausch-Williame-Watts)식으로 변형시킨 모델식을 이용하여 이를 매우 정확하게 표현할 수 있었다. 또한 고무치공구를 이용하여 열가소성 수지의 복합재료 성형공정을 실험하였고, 중성자 레디오그래피 촬영을 통하여 기공의 분포를 관찰하였다.

• Journal of Adhesion and Interface
• /
• v.16 no.2
• /
• pp.63-68
• /
• 2015

We synthesized thermoplastic polyurethane elastomer containing carboxylic acid group and TPV (thermoplastic vulcanizate). We measured the mechanical, grip, debris, contact angle and adhesion properties according to introducing acid group in elastomer structure. Mechanical and wet slip properties were improved because of the hydrogen bonding by introduction of acid group. Also adhesion strength was increased as increasing of surface polarity by carboxylic acid group. The debris property of TPV made from TPU containing carboxylic acid group was improved.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.2
• /
• pp.141-147
• /
• 2014

A nondestructive ultrasonic technique was applied to evaluate the thermal characteristics and degradation of synthetic polymer resin (plastics) with better cost-effectiveness and functionality than glass and metal. Thermoplastic and transparent acrylic resin (PMMA) specimens were annealed at below the glass transition temperature ($T_g$), and the propagation characteristics (attenuation and velocity) were measured. The attenuation increased and the velocity decreased with thermal degradation. The results showed that the thermal aging of the specimens could be evaluated quantitatively and that the Tg could be evaluated qualitatively.

• Composites Research
• /
• v.35 no.2
• /
• pp.75-79
• /
• 2022

In this study, the effect of mechanical and chemical properties of glass fiber reinforced thermoplastic (GFRTPs) according to the number of recycling was confirmed. The composite materials were manufactured through a hot press compression molding process using an E-glass chopped strand mat and a polypropylene film. Four specimens were named according to the number of recycled test repeat: First manufacture, 1st Recycle, 2nd Recycle, and 3rd Recycle. To investigate the mechanical properties of the prepared specimen, tensile test, flexural test, drop-weight impact test, differential scanning calorimetry (DSC), and field emission electron gun-scanning electron microscope (FE-SEM) was performed. As a result, as the number of recycling steps repeat, the degree of crystallization, tensile strength, elastic modulus, and flexural strength were increased, but the impact properties were greatly reduced.

• Composites Research
• /
• v.31 no.2
• /
• pp.63-68
• /
• 2018

Thermoplastic composite has been limitedly used in high performance aerospace industry due to relatively low mechanical properties even though it has various advantages. But, thermoplastic aromatic polymer composite has recently been researched and utilized much. In this study, PEEK and PPS neat resin film as representative thermoplastic aromatic polymer were processed through continuous heating, cooling and reheating cycle. Property change such as glass transition temperature and melting temperature were identified and crystallinity variation by different cooling rate were evaluated. In the first (heating) run, polymer specimens were kept for 5 minutes at higher temperature than melting point to remove previous thermal history, and crystallization reaction was controlled by adjusting cooling rate to 2, 5, 10, 20 and $40^{\circ}C/minute$ in the second (cooling) run. In the third (heating) run, specimen crystallinity were verified by measuring the melting enthalpy. The initial specimens containing high portion of amorphous structure exhibited cold crystallization and clear glass transition in the first run whereas they did not show in the third run due to the increase of crystalline structure portion. As cooling rate decreases through the second cooling run, the crystallinity of the specimen increased. PEEK polymer had 21.9~39.3% crystallinity depending on cooling rate change whereas PPS polymer showed 29.1~31.2%.

• Applied Chemistry for Engineering
• /
• v.26 no.2
• /
• pp.199-204
• /
• 2015

Thermoplastic road markings are one of the most widely used road markings in the world. However, the durability of domestic road markings is relatively shorter than that of the global average of, approximately, three years. To overcome it, the conventional thermoplastic road markings were prepared by adding polyolefin and oxidized PE wax to conventional petroleum resin. In addition, the melting viscosity was designed below 500 cP at $220^{\circ}C$ as well as the optimum viscosity for spray painting, and embedding ratio of glass beads were controlled about 50~60% by spraying in an interval of 1 second. Also the glass bead adhesive ratio was improved by reducing the amount of $CaCO_3$ below 40 wt%. The retroreflectivity was tested under four different conditions to evaluate the abrasion resistance of thermoplastic road markings. The retroreflectivity coefficient satisfied the international standard ($150mcd{\cdot}m^{-2}{\cdot}lux^{-1}$) in this study, and TPRM-7 was determined as an optimal ratio.

• The Journal of Korean Academy of Prosthodontics
• /
• v.56 no.3
• /
• pp.199-205
• /
• 2018

Purpose: This study evaluated the effect of nonthermal plasma treatment on the bond strength of autopolymerizing relining resin to the injection molded thermoplastic denture base resins (TDBRs) with different surface treatments. Materials and methods: Acrylic Resin (Acrytone), Polyester (Estheshot-Bright), Polyamide (Valplast) and Polypropylene (Weldenz) were subjected to various surface treatments: No treatment, Nonthermal plasma, Sandblasting, Sandblasting and nonthermal plasma. Specimens were bonded using an autopolymerizing relining resin. Shear bond strength was tested using universal testing machine with crosshead speed of 1 mm/min. Statistical analysis by two-way analysis of variance with Tukey's test post hoc was used. Results: Acrytone showed significantly higher shear bond strength value among other TDBR group while Weldenz had the lowest. The sandblasting and nonthermal plasma condition had significantly higher shear bond strength value in all of the resin groups (P < .05). Conclusion: The use of nonthermal plasma treatment showed limited effect on the shear bond strength between TDBRs and relining resin, and combination of nonthermal plasma and sandblasting improved the shear bond strength between TDBR and reline material.