• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.2
• /
• pp.103-108
• /
• 2012

A MILD (Moderate and Intense Low oxygen Dilution) combustor decreases NOx formation effectively during the combustion process and NOx formation is affected significantly by the exhaust gas entrainment rate toward fuel and air. The present study focused on the new MILD combustor, which has coaxial cylindrical tube. The outside tube of the new MILD combustor corresponds to the exhaust gas passage and the inner side tube is the furnace passage. The connection pipe is set between the outer side and the inner side tubes and coaxial air nozzle is inserted at the center of the connection pipe. A numerical analysis is accomplished to elucidate the characteristics of exhaust gas entrainment toward the inner furnace with the changes of air nozzle exit velocity, nozzle diameter, nozzle exit position and exhaust gas side pressure. The entrainment rate is proportional to the square root of air nozzle exit velocity and negatively proportional to the pressure difference between the exhaust gas side and furnace side pressures. The effect of air nozzle exit position is not considerable on the exhaust gas entrainment.

• Journal of Energy Engineering
• /
• v.23 no.3
• /
• pp.51-57
• /
• 2014

A MILD(Moderate and Intense Low oxygen Dilution) combustion, which is effective in the reduction of NOx, is considerably affected by the recirculation flow position of hot exhaust gas to the combustion furnace. A numerical analysis was accomplished to elucidate the flow characteristics in the MILD combustion incinerator for several cases with or without exhaust gas recirculation. It could be seen from the result of the present numerical study that the flow recirculation could be observed in the upper region over the vertical dividing wall for the case without exhaust gas recirculation. The optimal position of exhaust gas recirculation position was derived by the comparison of %RMS of x directional velocity for the cases with exhaust gas recirculation. The case with the exhaust gas recirculation position at the upper right of free board was the most effective with the smallest value of 57.4% RMS.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 1999.10a
• /
• pp.473-474
• /
• 1999

일반적으로 NOx배출은 연소과정에 의해 강력하게 지배되고 있으며, NOx 저감 기술은 1970년대 후반부터 많은 연구들이 수행되어, 그 이론들이 확립되고 있다. 석탄 연소시스템에서는 공기 다단(air staging, OFA), 연료다단(fuel staging, reburning) 및 배기가스 재순환(FGR) 등이 대표적인 NOx 저감 기술이며 [1∼4], 그 중 배기가스 재순환법은 저산소 배기가스를 연소용 공기에 재혼입시키므로써 NO의 생성속도를 저하시켜 NOx를 저감시키는 기법이다.(중략)

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1223-1230
• /
• 1989

본 연구에서는 이러한 관점으로부터, 개방식 연촉매치를 상정하여, 백금의 모노리스형 촉매를 이용한 메타놀예%%합형 촉매연소기의 정상운전의 실용성에 관한 실험 및 수치계산을 행하였다. 먼저 촉매연소기의 온도분포 및 배기가스 온도분포를 파악하고, 촉매연소기의 실용성을 평가하기 위하여 실내환경예측을 행하였다. 또한 실험만으로는 연소기의 여러가지 운전조건에 관한 전테이타를 얻는 것은 어렵다. 이 때문에 본 연구에서는, 이전의 연구에서 이용한 계산과 같이 메타놀이 완전연소하는 는 것으로 보고 중간산하물의 생성을 무시한 1차원 수치계산모델로 연소특성, 배기가 스의 배출특성등의 예측을 하였으며, 명종 운전 파라메타의 설정한계 등에 대하여 검토를 행하였다.

• Journal of the KSME
• /
• v.23 no.6
• /
• pp.427-433
• /
• 1983

내연기관의 성능은 실린더에서 연료의 화학에너지가 열에너지로 얼마만큼 빠르고 완전하게 변화하느냐에 좌우된다. 이를 위해서는 실린더 내에서 뜨거운 압축공기와 연료의 혼합 및 증기화가 요구된다. 엔진의 출력은 매 사이클당 흡입.압축할 수 있는 공기량에 좌우되므로 연소의 해석을 위해서는 실린더 내의 공기유동, 연료의 분무 및 연소과정을 이해 해야한다. 배기와 엔진효율의 요구성때문에 희박 혼합기 또는 EGR (exhaust gas recirculation)이 필요하게 된다. 그러나 희석이 크면 낮은 연소온도, 낮은 층류흐름속도와 화염전면의 낮은 난류강도 때문에 연소기간이 증대하게 된다. 실제로 희박의 증가는 실화 또는 긴 연소 지연기간, 사이클 마다의 연소맥동현상, HC배기의 증가등을 초래하게 된다. 이러한 저온연소의 단점들은 연소상태를 안정시키고 연소량을 증대시키는 공기의 유동을 이용해서 해결 될 수 있다. 최근에는 선회류와 난류의 강도를 증가시켜서 빠른연소(fast burning)를 이루고 있다. 선회류와 난류의 강도를 증대시키는 가장 중요한 2가지 방법은 흡입포트(port), 매니홀드(manifold)설계이다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.81-84
• /
• 2010

In this study, a coaxial swirl injector using hydrogen peroxide and kerosene was designed and combustion performance tests were performed to evaluate combustion characteristic according to mixture ratio. Spray characteristic of the injector was verified by cold flow test and combustion performances according to mixture ratio were evaluated by the characteristic exhaust velocity. Test results showed that the combustion efficiency at the design condition was about 95% and the pressure fluctuation was very small.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.1
• /
• pp.51-57
• /
• 2013

This study aims to experimentally investigate the combustion characteristics of a lean premixed swirl-stabilized burner with dual-stage fuel injection arrays. The results show that a variation in the fuel distribution to fuel stages 1 (upstream) and 2 (downstream) produces a noticeable change in the NOx and CO emissions. Reducing the confined ratio, defined as the ratio of the nozzle exit diameter to the liner diameter, may reduce NOx and CO emissions owing to reduced combustion loading and longer residence time, respectively. A nozzle exit velocity of 30 m/s shows the optimum characteristics in terms of NOx and CO emissions and flame stability: increasing or decreasing the nozzle exit velocity leads to a degradation in emissions or flame stability, respectively.

• Journal of the Korean Institute of Gas
• /
• v.21 no.3
• /
• pp.53-60
• /
• 2017

Various researches have been conducted for the reduction of NOx at the combustion furnace and exhaust gas recirculation method is commonly used technology for NOx reduction. The present research adopted coanda nozzles at the outside pipes of furnace to entrain the exhaust gas for the exhaust gas recirculation and the mixed gas was ejected to the tangential direction to cause the swirl flow in the furnace. The combustion flow characteristics in the exhaust gas recirculation burner with coanda nozzle has been elucidated by analyzing the swirl flow streamlines, temepraure and reaction rate distribution in the furnace. The exhaust gas entrained flow rate has been investigated by changing the excess air factor and coanda nozzle gap and the exhaust gas entrained flow rate increased with the increase of excess air factor and it decreased with the increase of coanda nozzle gap. The mean temperature at the exit plane of exhaust gas decreased with the excess air factor and it was little affected by the increase of coanda nozzle gap. The NOx mass fraction at the exhaust gas exit plane remarkably decreased with the excess air factor and it was also little affected by the increase of coanda nozzle gap.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.129-132
• /
• 2012

In this study, combustion performance tests of a multi coaxial-swirl injector engine using hydrogen peroxide and kerosene as propellants were performed to evaluate combustion characteristic according to mixture ratio between 6.0 and 9.0 by criterion of designed(7.6). Combustion characteristics were evaluated by calculated characteristic exhaust velocity($c^*$) and pressure fluctuation. Test results showed that the combustion efficiency was over 90% and the pressure fluctuation was within 1%.

• Journal of Energy Engineering
• /
• v.22 no.4
• /
• pp.413-419
• /
• 2013

The present study used the MILD combustor, which has coaxial cylindrical tube. The outside tube of the MILD combustor corresponds to the exhaust gas passage and the inner side tube is the furnace passage. A numerical analysis was accomplished to elucidate the characteristics of exhaust gas entrainment toward the inner furnace with the changes of venturi nozzle geometrical parameters, nozzle position, nozzle gap between high pressure air nozzle and venturi nozzle, and with the change of high pressure nozzle inlet velocity. The entrainment flow rate for the case with the high pressure air nozzle attached at the exhaust gas wall has relatively small change with the change of nozzle gap. That for the case with the high pressure air nozzle exposed to the exhaust gas has monotonically increase with the change of nozzle gap. The flow rate ratio of entrainment flow rate has considerably increase tendency with relatively lower air inlet velocity, on the other hand, that with relatively higher air inlet velocity could be seen relatively small increase.