• Journal of the Korea Concrete Institute
• /
• v.24 no.3
• /
• pp.259-266
• /
• 2012

A general earthquake resistant design philosophy of ductile frame buildings allows beams to form plastic hinges adjacent to beam-column connections. In order to carry out this design philosophy, the ultimate bond or shear strength of the beam should be greater than the flexural yielding force and should not degrade before reaching its required ductility. The behavior of RC members dominated by bond or shear action reveals a dramatic reduction of energy dissipation in the hysteretic response due to the severe pinching effects. In this study, a method was proposed to predict the deformability of reinforced concrete members with short-span-to-depth-ratios, which would result in bond failure after flexural yielding. Repeated or cyclic loading produces a progressive deterioration of bond that may lead to failure at lower cyclic bond stress levels. Accumulation of bond damage is caused by the propagation of micro-cracks and progressive crushing of concrete in front of the lugs. The proposed method takes into account bond deterioration due to the degradation of concrete in the post yield range. In order to verify bond deformability of the proposed method, the predicted results were compared with the experimental results of RC members reported in the technical literature. Comparisons between the observed and calculated bond deformability of the tested RC members showed reasonably good agreement.

• Journal of the Korea Concrete Institute
• /
• v.15 no.5
• /
• pp.705-714
• /
• 2003

Even though Korean peninsula is located in regions of moderate seismic risks, current seismic design provisions of the roadway bridge design code have adopted the AASHTO code which is based on the requirements for high seismic regions. The objective of this research is to investigate the seismic performance of circular reinforced concrete (RC) bridge piers with limited ductility, which may be desirable in low or moderate seismic regions, such as in Korea. Four test specimens were designed and constructed. The reference specimen was designed with longitudinal steel ratio as 1.01% and the confinement reinforcement ratio as 0.13% without considering earthquake, and three other test specimens were designed in accordance with a limited-ductility concept as 0.3% for the confinement steel ratio. This confinement ratio is 0.32 times of minimum lateral reinforcement specified in current seismic design provisions, and 2.3 times of lateral reinforcement required in nonseismic design provisions. The pseudo-dynamic test was carried out to evaluate the seismic performance of full-scale specimens in size of 1.2m diameter and 4.8m height. Judging from the experiment, the reference specimen was not satisfactory for the demand displacement ductility ${\mu}$=5.0, but three limited-ductility specimens appeared to have the displacement ductility of more than 5.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.2
• /
• pp.187-192
• /
• 2016

While structures are designed within elastic range by other designs, plastic behavior of structures should be verified and controlled in order to prevent structural collapse by the earthquake resistant design. No Collapse Requirement for typical bridges is to avoid falling down of superstructure by way of plastic behavior of certain structural elements and to operate emergency vehicles after earthquake. Such plastic behavior is restricted to connections or pier columns and appropriate measures are required for each case. Earthquake Resistant Design part of Roadway Bridge Design Code provides design processes for Ductile Collapse Mechanism by forming plastic hinges at pier columns. Also for bridges with reinforced concrete piers ductility-based design processes are provided as an appendix constructing Brittle Collapse Mechanism with connection yielding. In this study, a typical bridge with steel bearing connections and reinforced concrete piers is selected and No Collapse Design procedure considering both Ductile and Brittle Collapse Mechanism is proposed together with revisions required for the Earthquake Resistant Design part.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.99-99
• /
• 2018

본 연구는 무전해 니켈 도금 공정에서 고연성을 요구하는 Flexible 기판상에 많이 사용되어지고 있는 무전해 니켈 도금액 평가에 관한 것이다. 무전해 도금을 이용하여 도금된 표면은 다양한 패키징 분야에서의 높은 밀도를 가지는 초소형 소자 등의 실장 표면이나 접합 계면으로 사용되고 있는 등 부품 소재 산업에서의 중요성이 점차 증가되고 있다. 고연성 무전해 Ni-P 도금개발을 통하여 얻고자하는 기술적 과제는 도금층에 높은 연성을 제공하고 안정성이 향상된 무전해 니켈 도금액을 제공하는 것이다.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.441-444
• /
• 2010

대공간 구조물과 초고층 빌딩에 있어 건축물의 자중 감소에 대한 요구가 늘어나고 있으며 이에 대한 가장 효과적인 방법 중 하나는 경량 콘크리트를 사용하는 것이다. 본 연구는 최외단 철근의 순인장 변형률에 따른 경량콘크리트 보의 휨 거동 및 휨 성능을 평가하는 것에 그 목적이 있다. 크기와 형상이 동일한 보통중량 콘크리트 보 1개와 경량 콘크리트 보 4개의 총 5개 시험체를 제작하여 최외단 철근의 순인장 변형률을 변수로 실험을 수행하였으며 이를 통해 순인장 변형률에 따른 경량콘크리트 보의 강도와 연성의 변화를 분석하였다. 실험 결과 최외단 철근의 순인장 변형률이 증가할수록 시험체의 연성비는 증가하였으며 최대하중과 강성은 감소하였다. 특히 순인장 변형률 0.005 이상에서 연성지수 2 이상을 확보할 수 있었다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.2
• /
• pp.87-94
• /
• 2014

In solid mechanics, the peridynamics theory has provided a suitable framework for material failure and damage propagation simulation. Peridynamics is computationally expensive since it is required to solve enormous nonlocal interactions based upon integro-differential equations. Thus, multiscale coupling methods with other local models are of interest for efficient and accurate implementations of peridynamics. In this study, peridynamic models are restricted to regions where discontinuities or stress concentrations are present. In the domains characterized by smooth displacements, classical local models can be employed. We introduce a recently developed blending scheme to concurrently couple bond-based peridynamic models and the Navier equation of classical elasticity. We demonstrate numerically that the proposed blended model is suitable for point loads and static fracture, suggesting an alternative framework for cases where peridynamic models are too expensive, while classical local models are not accurate enough.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.10 no.3 s.49
• /
• pp.57-64
• /
• 2006

Seismic design codes are mainly based on the research results for the inelastic response of structures in high seismicity regions. Since wind loads and gravity loads may govern the design in low seismicity regions in many cases, structures subjected to design seismic loads will have larger overstrength compared to those of high seismicity regions. Therefore, it is necessary to verify if the response modification factor based on high seismicity would be adequate for the design of structures in low seismicity regions. In this study, the adequacy of the response modification factor was verified based on the ductility and overstrength of building structures estimated from the result of nonlinear static analysis. Framed structures are designed for the seismic zones 1, 2A, 4 in UBC-97 representing the low, moderated and high seismicity regions and the overstrength factors and ductility demands of the example structures are investigated. When the same response modification factor was used in the design, inelastic response of structures in low seismicity regions turned out to be much smaller than that in high seismicity regions because of the larger overstrength of structures in low seismicity regions. Demands of plastic rotation in connections and ductility in members were much lower in the low seismicity regions compared to those of the high seismicity regions when the structures are designed with the same response modification factor.

• Journal of Korean Society of Steel Construction
• /
• v.13 no.1
• /
• pp.19-28
• /
• 2001

The strength and ductility of steel flexural members are investigated experimentally in this study. As for the performance evaluation of flexural members. experimental studies on the 9 test specimens were carried out. Four specimens were fabricated from SM490 and five specimens were fabricated from SM570. The experimental results of the specimens were analyzed with focus on the flexural strength and ductility. The experimental results exhibited that all the specimens provided sufficient flexural strengthes which exceeded the nominal flexural strengthes specified in the current Limit State Design Specification by average ratio of 1.22. However. the experimental results showed that the compact-section specimens fabricated from SM570 did not provide the required rotational ductility. The yield-to-tensile strength ratio(YR) of SM570 of about 0.9 might be the causes of such insufficient capacities.

• The Journal of the Acoustical Society of Korea
• /
• v.29 no.7
• /
• pp.448-457
• /
• 2010

Vibrations and wave propagations in waveguide structures can be analysed efficiently by using waveguide finite element (WFE) method. The WFE method only models the 2-dimensional cross-section of the waveguide with finite elements so that the size of the model and computing time are much less than those of the 3-dimensional FE models. For cylindrical shells or pipes which have simple cross-sections, the external coupling with fluids can be treated theoretically. For waveguides of complex cross-sectional geometries, however, numerical methods are required to deal with external fluids. In this numerical approach, the external fluid is modelled by the boundary elements (BEs) and connected to WFEs. In order to validate this WFE/BE method, a pipe submerged in water is considered in this study. The dispersion diagrams and point mobilities of the pipe simulated are compared to those that theoretically obtained. Also the acoustic powers radiated from the pipe are predicted and compared in both cases of air and water as an external medium.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1993.04a
• /
• pp.30-34
• /
• 1993

기계구조물이 고속화, 경량화 됨에 따라 더 정밀한 구조물의 설계 및 해석이 요구되어지고 있고, 이에 따라 단속적모형 보다 한 단계 더 나아가 분포변수 모형으로 구조물을 모형화하게 된다. 특히 나선형 스프링은 기계구조물에서 가장 널리 사용되는 일반적인 요소로서, 그 형상이 공간상의 굽은 봉 형상이 므로 연성된 편미분방정식 형태로 지배방정식이 기술된다. 나선형 스프링 해 석은 Michell(1890)과 Love(1899)의 정적해석을 시작으로 Phillips와 Costello [1]의 'SimpleTheory' 및 Wittrick [3]의 지배방정식등 매우 복잡한 연성된 편미분방정식 형태를 지니고 있다. 그러나 이와 같은 편미분방정식은 해석하 기가 매우 어려워 수치해법으로도 간단한 경우에 한해서만 해석하여 왔다. 본 연구에서는 이와 같은 연성된 편미분방정식을 해석하기 위하여 보다 구 조진동문제에 적합한 수치해법을 제안하고, 이를 이용하여 나선형 스프링의 강제과도진동 응답을 정확하고 효율적으로 구하였다.