• The Journal of Engineering Geology
• /
• v.8 no.3
• /
• pp.235-245
• /
• 1998

Adquate friction resistance is needed to prevent pavement slipperiness and to allow vehicles to stop in a reasonable distance. Performance of the aggregates is reduced over time by wear and polishing as a consequence of vehicular traffic. In this research, the objective was to develop a laboratory method to test Indiana gravel aggregates to predict field performance, and determine causes for the range of values amang gravel aggregates. The assessment of gravel sources was primarily on the basis of individual rock types and those proportions comprising the gravel. Polish and friction values were determined in the laboratory with the British Wheel and Pendulum. The gravels of this study were composed primarily of carbonate aggregates that showed considerable variability in polishing thresholds. Igneous and metamorphic constituents polished to a lesser degree and are expected to improve overall aggregate performance. Estimates of the IFV (Initial Friction Value) and PV (Polished Value) for crushed gravel samples can be made based on the percentage of rock types present in the sample. A weighted average is used to make this calculation.

• Journal of Power System Engineering
• /
• v.10 no.1
• /
• pp.46-51
• /
• 2006

Present study was investigated the effect of the particle of the counterface of unidirectional carbon fiber reinforced composite. The friction coefficient of composite and the specific wear rate different sliding velocity were measured for this materials. The friction track of counterface was observed by an optical microscope and scanning electron microscope. There were insignificant effects of the specific wear rate under lower Sic abrasive particle, however it showed high effect on $30{\mu}m$ abrasive particle size. There were significant effects of friction and wear behavior of the fiber direction under 0.3m/s sliding speed. Major failure mechanisms can be classified such as microfracture, plowing, microcutting, cutting and cracking.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.132.2-132.2
• /
• 2017

플라즈마 전해 산화(Plasma Electrolytic Oxidation, PEO)는 Al, Ti, Mg 합금과 같은 경량 금속소재에 대한 표면처리기술로서 주목을 받고 있다. PEO 처리에 의해 표면에 치밀하게 형성되는 세라믹 산화층은 우수한 내식성, 내마모성을 보유하기 때문에, 이와 같은 특성이 요구되는 분야에 적용하기 위한 연구가 활발하다. 특히 PEO 세라믹 코팅층의 응착마모(adhesive wear)와 절삭마모(abrasive wear)에 관한 연구는 상당부분 이루어지고 있으나, 캐비테이션 침식과 같은 침식마모(erosive wear) 특성에 관한 연구는 부족한 실정이다. 본 연구에서는 알루미늄 합금 소지에 제작된 PEO 코팅층의 캐비테이션 손상 특성을 고찰하였으며, 전해액 조성이 PEO 코팅층의 미세조직과 캐비테이션 손상 특성에 미치는 영향을 살펴보았다. PEO 처리를 위해 사용된 소재는 상용 5083-O합금 판재로서 $2cm{\times}2cm$로 절단하여, 에머리페이퍼로 1000번까지 연마하여 사용하였다. 사용된 전해액은 증류수에 KOH(1 g/L)을 base로 하여 $Na_2SiO_3$(2 g/L)의 첨가유무를 변수로 하였다. 시편을 양극으로 하고 STS304를 음극으로 하여 각각 DC 전원 공급기의 +극과 -극에 연결하였으며, 정전류 조건에서 30분간 $0.1A/cm^2$의 전류밀도를 인가하였다. PEO 처리후 시편은 SEM, EDS, XRD를 이용하여 표면 특성 평가를 실시하였다. PEO코팅층의 캐비테이션 특성 평가는 초음파 진동식 캐비테이션 발생 장치를 이용하였으며, 캐비테이션 실험 후 시간에 따른 표면 거칠기의 변화 거동을 분석하였다.

• ETRI Journal
• /
• v.14 no.1
• /
• pp.108-117
• /
• 1992

광통신 시스팀에서 신호접속용으로 사용되는 광커넥터의 결합기구 중 세라믹 페룰-슬리브의 정렬기구에서 발생하는 성능저하 현상을 다루었다. 성능저하 현상으로 페룰 단면연마시 발생하는 Vertex Eccentricty, 좌굴현상, 환경에 따른 탄성 및 응력의 변화, 마모, 피로파괴 등에 대한 이론적인 배경과 실험결과를 토대로 특성에 대한 영향을 분석하였다.

• Proceedings of the Korean Fiber Society Conference
• /
• 2001.10a
• /
• pp.401-402
• /
• 2001

Polishing pads were widely used industry and domestic needs such as finishing processing, surface cleaning. Especially, it is necessary to require inherent luster of metal. The spot on metal surface polishing and lifetime were depended on properties of constituted fiber in polishing pads. (omitted)

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.9
• /
• pp.1005-1012
• /
• 2014

Gears are critical elements in automobiles, and their use as power transmitting machine elements in engineering applications is quite extensive. In the areas of contact between gear teeth, the condition of a gear is likely to deteriorate due to contact fatigue, wear, material defects, lubrication failure, etc. Thus, it is necessary to monitor its condition to ensure smooth power transmission. Gear teeth deterioration causes failures such as abrasive wear, scuffing, pitting, and spalling. These failures lead to a higher level of vibration signals in the gear system. This paper presents the results of an experiment on the surface fatigue wear of a spur gear system. The correlation between the estimated specific film thickness, statistical parameter of the vibration signals, and Stribeck curve was considered in this study.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.10
• /
• pp.1117-1123
• /
• 2014

This study sintered $Si_3N_4$ with different amounts of $SiO_2$ nano-colloid. The surface of a mirror-polished specimen was coated with $SiO_2$ nano-colloid, and cracks were healed when the specimen was treated at a temperature of 1273 K for 1 h in air. Wear specimen experiments were conducted after heat treatments for 10 min at 1073, 1273, and 1573 K. The heat-treated surface that was coated with the $SiO_2$ nano-colloid was slightly rougher than the noncoated surface. The oxidation state of the surface according to the heat treatment temperature showed no correlation with the surface roughness. Moreover, the friction coefficient, wear loss, and bending strength were not related to the surface roughness. $Si_3N_4$ exhibited an abrasive wear behavior when SKD11 was used as an opponent material. The friction coefficient was proportional to the wear loss, and the bending strength was inversely proportional to the friction coefficient and wear loss. The friction coefficient and wear loss increased with increasing amounts of the $SiO_2$ nanocolloid. In addition, the friction coefficient was slightly increased by increasing the heat treatment temperature.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.28 no.2
• /
• pp.261-270
• /
• 2001

This study was performed to evaluate wear characteristics of light-cured composites when opposed by human enamel. Seven light-cured restorative composites were selected and enamel cusps sectioned from premolars. All samples were stored in distilled water at $37^{\circ}C$ for 10 days. 68.6 N of weight was loaded during the test. The measurements of vertical loss of enamel cusps, weight loss and volume loss of composites, and SEM observations of the polished and abraded surfaces were made after 30,000 cycles. The results obtained were summarized as follows; 1. The highest hardness value of 70.4 was observed in the Spectrum group and the lowest value of 19.8 was observed in the Heliomolar group. Results of Tukey test showed that an overall significant difference was indicated except the Spectrum, Z100 and Clearfil AP-X groups(p<0.05). 2. Enamel showed the good abrasion resistance against the Heliomolar group of microfilled composite and the Palpique Toughwell group containing the submicron hybrid type spherical fillers. 3. The abrasive wear resistance of hybrid composites was improved with the decrease of mean particle size and hybrid of submicron particle fillers. 4. SEM observation of worn surfaces revealed the protrusion, attrition and missing of fillers, cracks developing and delamination in the matrix.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.33 no.4
• /
• pp.633-642
• /
• 2006

This study evaluated the surface changes such as surface average roughness(RA), surface free energy(SFE) and wear depth among groups treated with surface penetrating sealant(Fortify, Biscover), non treated polishing group before and after tooth-brushing, analyzing the influence of the sealants in filling of surface microdefects formed during the finishing and polishing procedures of composite resin. Results were as follow(p= 0.05) : 1. Ra was increased Biscover. Fortify and Polishing group. Before abrasion and in 6 months, all groups were statistically significant. In 1 month, 2 months and 3 months no statistical difference was noticed between Fortify and Biscover 2. SFE of Polishig and Biscover group. Fortify and Biscover group were statistically significant before abrasion. SFE of Polishing and Fortify group was statistically significant in 1 month. No statistical difference was noticed among groups in 2 months. SFE of Fortify and Biscover group was statistically significant in 3 months. Polishing and Fortify group, Fortify and Biscover group were statistically significant in 6 months. 3, Wear rate between Polishing and Fortify group was statistically significant in only 1 month. Wear rate between Polishing and Biscover group was statistically different in each month except for 2 month and so it was between Fortify and Biscover group. Considering film thickness of Fortify and Biscover, Fortify almost discappeared after 2 months and Biscover did after 6 months.

• Tribology and Lubricants
• /
• v.34 no.3
• /
• pp.115-122
• /
• 2018

Chemical mechanical polishing (CMP) is a hybrid processing method in which the surface of a wafer is planarized by chemical and mechanical material removal. Since mechanical material removal in CMP is caused by the rolling or sliding of abrasive particles, interfacial friction during processing greatly influences the CMP results. In this paper, the trend of tribology research on CMP process is discussed. First, various friction force monitoring methods are introduced, and three elements in the CMP tribo-system are defined based on the material removal mechanism of the CMP process. Tribological studies on the CMP process include studies of interfacial friction due to changes in consumables such as slurry and polishing pad, modeling of material removal rate using contact mechanics, and stick-slip friction and scratches. The real area of contact (RCA) between the polishing pad and wafer also has a significant influence on the polishing result in the CMP process, and many researchers have studied RCA control and prediction. Despite the fact that the CMP process is a hybrid process using chemical reactions and mechanical material removal, tribological studies to date have yet to clarify the effects of chemical reactions on interfacial friction. In addition, it is necessary to clarify the relationship between the interface friction phenomenon and physical surface defects in CMP, and the cause of their occurrence.