• Proceedings of the KAIS Fall Conference
• /
• 2010.05b
• /
• pp.988-991
• /
• 2010

본 연구는 직접 연료분사 가솔린 엔진에 장착되는 고압연료 인젝터의 연료공급 특성에 대한 것으로, 두 종류 GDI 인젝터의 분무가시화 실험을 수행하였고, 분무특성을 분석하였다. 가시화 실험을 통하여 인젝터 끝단 분사 초단부근 연료거동을 확인하였고, 인젝터의 특성인 도달거리와 관통력을 확인하였으며, 분위기 압력의 변화에 따른 분무특성을 고려하여 실험을 수행하였다. 두 인젝터 모두 분위기 압력이 증가함에 따라 도달거리와 분사각이 감소하였다. B type의 인젝터 보다 A type의 인젝터가 분위기 압력에 민감한 것으로 나타났다. 본 연구를 통하여 분위기 압력의 변화에 따른 분무거동의 변화를 확인 하였으며 직접 분사인젝터의 엔진적용을 위한 기초 분무 데이터를 확보하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.9
• /
• pp.569-576
• /
• 2016

The objective of this study was to investigate, using a numerical method, the fuel injection targeting for improving the combustion performance in a HSDI diesel engine. In this work, the ECFM-3Z model was applied as the combustion model, and the injection mass, inclined spray angle, and injection timing were varied for the study on the targeting of fuel spray. The results of this work were compared in terms of cylinder pressure, rate of heat release, and exhaust emissions characteristics. It was found that the cylinder pressure increased when the injection timing was advanced, and the rate of heat release increased when more fuel was injected into the piston bowl. In addition, $NO_x$ emission increased owing to the increase in the rate of heat release. On the other hand, CO and soot emissions decreased because of the improvement in combustion performance.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.3
• /
• pp.22-30
• /
• 2011

There is a many way of LPRE throttling methods, high-pressure-drop systems, dual-manifold injector, gas injection, multiple chambers, pulse modulation and movable injector components. Especially dual-manifold injector is essentially combines two fixed-area injectors into a common structure, with independent feed systems controlling flow to each injector manifold. In this paper, using indirect photography and liquid film thickness measurement with various injection pressure and tangential entry diameter to decide stability of spray over a wide thrust range in dual manifold injector.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.405-409
• /
• 2010

금속분말을 청정 에너지원으로 이용하기 위해 금속분말 소형 연소기의 구현이 필요하다. 이를 위한 선행연구로 연료 공급 시스템인 핀틀인젝터형(pintle injector type) 금속분말 공급장치의 중요 성능인 분사량을 실험적으로 측정하였다. 분사량 측정 시험에 앞서 간단한 금속분말 공급 시험으로 확인된 문제점을 장치의 변경을 통해 해결하였다. 측정 시험의 결과, 연료 공급 장치에 이송 가스 압력이 상승함에 따라 많은 질유량의 금속분말이 분사되었고 압력에 따른 정량적 분사량을 확인하였다. 이송 가스와 금속분말의 혼합 성능을 개선하여 균일한 분사를 하고자 이송 가스를 25 Hz로 가진 하여 공급하였고 가진이 없는 경우의 실험결과와 비교하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.1
• /
• pp.61-69
• /
• 2004

This paper describes numerical efforts to characterize the flame-holding and air-fuel mixing process of model SCRamjet engine combustor, where a hydrogen jet injected into a supersonic cross flow and in a cavity Combustion phenomena in a model SCRamjet engine, which has been experimentally studied at University of Queensland and Australian National University using a free-piston shock tunnel, was observed around separation region of upstream of the normal injector and inside of cavity. The results show that the separation region and cavity generates several recirculation zones, which increase the fuel-air mixing. Self ignition occurs in the separation-freestream and cavity-freestream interface.

• Journal of Aerospace System Engineering
• /
• v.12 no.4
• /
• pp.81-89
• /
• 2018

In the present study, a numerical investigation was conducted to analyze the effect of the distance between the adjacent injectors on the characteristics of flow structure, fuel penetration, and air/fuel mixing. Numerical results were validated with experimental data using a single injection. Subsequently, the same injector geometry and properties were applied on a non-reacting flow simulation with multiple injectors. Total pressure loss, penetration height, and mixing efficiency were compared with the distance between the injectors. The results showed that each injected gas merged into a single stream, resulting in the 2D-like flow fields under the condition of short distance and lower mixing efficiency along with higher total pressure loss. When the distance between the injectors increased, total pressure loss reduced and mixing efficiency increased due to the weakening of interactions between the injected gases.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.300-303
• /
• 2010

This work shows the result of numerical simulation on a reacting flow by varying atomization properties which can be obtained from a injector for a small and low power aircraft gas turbine engine. Because the atomization properties mainly affect on the performance of the engine, a lot of efficiency tests are needed when a new injector is developed. Nowadays researches has been actively performed using computational analysis. Using commercial package CFD-ACE+, basic studies on the reacting flow field have been conducted. Those results show that the reaction rate is increased when higher pressure and wider angle spray condition are used. More smaller parcels can also enhance the fuel-air reaction.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1995.11a
• /
• pp.56-61
• /
• 1995

균일한 속도를 갖는 주유동장에 연료를 분사하였을때 분사된 연료가 주유동장의 공기와 혼합되는 정도를 정량적으로 설명하기 위하여 실험과 수치 계산을 실시하였다. 본 연구에서는 혼합 진전 정도를 나타내기 위하여 혼합진전변수(mixing progress variable)를 도입하여 유동조건에 따라 혼합 정도를 정량적으로 비교하였다. 주유동 속도가 일정할때 분사 속도를 증가시키면 연료가 주유동장의 공기와 혼합이 촉진됨을 알 수 있었다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.13 no.4
• /
• pp.63-74
• /
• 1989

It is well-known that the fuel injection system if a diesel engine has taken a more important place in understanding of diesel combustion process with combustion chamber. But a diesel fuel injection system has an assembly of many complex and intricate problems such as the desired rate of injection, secondary injection and injection pump etc., in addition to the atomization for ignition and combustion, the penetration and diestribution for proper utilization of air. The analysis is carried out by simplifing and modeling the injection phenomena and dividing into three parts comprising of fuel injection pump, high pressure pipe and fuel injection nozzle. The purpose of this paper is to describe an analytical simulation of the injection system and to speed up the work of developing injection systems for new engines. The effects of important injection parameters as predicted by the present model are found to be in good agreement with experiment. It can be seen that there is an optimal pipe diameter for maximum quantity injected.

• Journal of ILASS-Korea
• /
• v.1 no.1
• /
• pp.85-91
• /
• 1996

This experiment was undertaken to investigate spray characteristics of the conventional inject ion system and the ultrasonic energy added inject ion system. Sauter mean diameter was mesured under the variation of inject ion pressure and the spray distance. To measure the droplet size we used the Malvern system 2600C. The spray angle and mass distribution was analyzed to the CCD camera and the patternater. After experiment, it was found that the ultrasonic energy added injection system had smaller sauter men diameter of droplet, wider mass distribution and wider spray angle than the conventional inject ion system had.