• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.1
• /
• pp.108-114
• /
• 1998

This paper presents the design and fabrication of waveguide E-plane metal insert bandpass filter for milli-meter waves which is analyzed transmission characteristics by calculating the generalized scattering matrix using mode-matching method. The bandpass filter was fabricated to verify the proposed method by the WR-34 rectangular waveguide to operate in 30.085 ~ 30.885 GHz. The fabricated waveguide E-plane metal insert band- pass filter was established the fact that it is so adaptive for milli-meter waves due to the measured data closely consistent with the results of analysis using mode-matching method, that is, the maximum value of insertion loss is 0.8 dB and the return loss is below -15 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.1
• /
• pp.14-19
• /
• 2003

In this paper, a λ/4 hair-pin resonator is proposed to reduce the size of resonators. A LTCC MLC bandpass filter is designed using the λ/4 hair-pin resonators. The electromagnetic coupling structure between two planar resonators is analysed. The equivalent circuit is derived to explain the behavior of the LTCC MLC bandpass filter using λ/4 hair-pin resonators. A design procedure is also described. The simulated and measured results of 1.8 GHz band 2-pole bandpass filter are presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.3
• /
• pp.355-360
• /
• 2012

In this paper, an stepped-impedance low pass filter(SI-LPF) of triangular-patch type is proposed. A SI-LPF designed according to the standard SI-LPF design procedure is folded as a right angled triangle. The figure of merits of this structure are the adjustabilities of the cut off frequency, the stopband and the attenuation pole frequency of the proposed LPF by varying the resultant slots after folding the SI-LPF compactly for miniaturization. The size of the fabricated LPF is $13.75mm{\times}6.875mm$, which is 24.4 % reduced one compared to that of the conventional SI-LPF. The measured results of the LPF show return loss of less than -10 dB at passband, insertion loss of less than -10 dB at stopband and wide stopband from 3.5 GHz to 10 GHz (about $3f_c$).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.7
• /
• pp.1237-1242
• /
• 2016

In this paper, the low pass filter with harmonics suppression and rejection using parallel coupled-line and radial type open stub is presented. And the resultant characteristic of the proposed low pass filter is that the harmonics are suppressed and rejected in wide bandwidth due to the parallel coupled-line structure. The open stub of a low pass filter is constructed in radial type which can be used to adjust the size of filter. The size of the proposed low pass filter is $6.98{\times}7.60mm2$ and the cut off frequency is 2.45 GHz. And the filter is economical in unit cost and can be constructed easily and has the merit of mass product because the filter is composed of distributed element. Also, the widely rejected harmonics is 128 % in the bandwidth and the insertion and return losses of the low pass filter are 1.07 dB and 19.5 dB, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.2A
• /
• pp.167-173
• /
• 2008

In this paper, the flexible narrow bandpass filters (BPFs) with ${\lambda}$g/4 short and ${\lambda}$g/2 open stubs by microstrip line on duroid substrate are suggested. These BPFs with narrow bandwidth show flexible bandwidth with variation of the position of the stubs using the Qe (external quality factor) without changing the impedance value at microwave range. On the other hand, by replacing the series quarter-wavelength connecting lines with the equivalent T-shaped line of bandstop filter(BSF), the compact stub bandpass filter with harmonics suppression can be realized. The BPF with ${\lambda}$g/4 short stubs shows the insertion loss of 2.1 dB and the return loss of 18 dB and BPF with ${\lambda}$g/2 open stubs shows the insertion loss of 1.2 dB and the return loss of 21.9 dB at the center frequency of 5.8 GHz and the bandwidth of 10 %.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.7
• /
• pp.1255-1260
• /
• 2009

Microstrip interdigital filter is designed with the width and length of a resonator, the gap distance between resonators and the location of a tap. When designing filters, it is a benefit to design with few design parameters comparing to many design parameters. In this paper we design and implement two microstrip interdigital filters operating in the UWB(Ultra Wide-Band) frequency band, one using a fixed width of a resonator and the other using a different width of resonators. The test results of the implemented filters show that the low-band high filter with a fixed width has the insertion loss of 1.49dB, -10dB band width of 720MHz, -35.7dBattenuation at 4.8GHzand below -13dB of S11. The filter with a different width of resonators has the insertion loss of 1.6dB, -10dBbandwidth of 1.63GHz and below-8dBof S11.

• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 1997.11a
• /
• pp.211-220
• /
• 1997

체비셰프 삽입손실법을 이용하여 선택도가 높은 대역 여파기를 설계한다. 체비셰프 방식은 차단주파수 근방 곡선의 경사가 버터워쓰에 비해 급격하게 떨어지는 특징을 가진다. 인접 채널의 간섭을 최소화 하기위해 차단 대역의 감쇄를 70db이상으로 유지한다. 중심주파수는 885MHz에서 통과대역폭 10MHz의 여파기를 제작하였다.

• 한국ITS학회:학술대회논문집
• /
• 2005.11a
• /
• pp.245-248
• /
• 2005

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.352-356
• /
• 2003

본 논문에서는 매우 넓은 저지대역과 우수한 cutoff 특성을 갖는 저역통과 여파기를 제안하였다. 접지면 슬롯과 급전면 개방 스터브의 특성을 결합한 기존의 광대역 여파기에서 전송선의 길이를 ${\lambda}_g/4$로 변형함으로써 기존의 여파기보다 더 작은 크기로 넓은 저지대역과 급격한 cutoff 특성을 얻을 수 있었다. 또한 설계한 단위 여파기를 특정 간격로 배열하여 더 깊은 저지대역과 향상된 cutoff 특성을 얻을 수 있었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.273-276
• /
• 2003

본 논문에서는 한쪽이 단락된 스트립선로(Stripline)와 Loading 캐패시턴스(Capacitance)로 구성된 새로운 형태의 1/4파장 스트립선로 공진기를 제안하였으며, 이 공진기를 이용해서 5.2 GHz 대역 무선 LAN용 적층 대역통과 여파기를 설계, 제작 하였다. 제안한 공진기의 전파지연효과(Slow-wave Effect) 때문에, 기존의 공진기에 비해서 길이가 축소되며, 기준 공진주파수(Fundamental Resonant Frequency)에 대한, 첫 번째 기생공진주파수(First Spurious Resonant Frequency) 값이 커지기 때문에, 넓은 상향저지대역(Wide Upper Stopband)을 갖는 초소형의 대역통과 여파기의 설계가 가능하다. 설계한 여파기를 LTCC 적층 공정 기술을 이용하여 제작하였으며 그 크기는 $3.2mm{\times}1.6mm{\times}0.8mm$ 이다.