• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.881-884
• /
• 2011

Secondary throat supersonic exhaust diffusers were designed by Normal-shock theory and manufactured. Experimental studies of the diffusers were performed using nitrogen gas of room temperature. It showed a difference about 18% between the experimental and theoretical results. The difference was shown by friction loss at the wall of the diffuers.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.04a
• /
• pp.115-123
• /
• 1998

A $Si_3N_4$ tappet shim was devdoped in a direct OHC engine for the friction reduction of valve train system that contributes significantly to the engine friction in real driving condition. For commercializing $Si_3N_4$ tappet shim, it is important to reduce the machining cost. Therefore we analytically and experimentally figure out the optimum condition. Using ceramic tappet shims machined with different surface roughness, the effects of roughness on the friction loss were analyzed in view of the lubrication behavior. From this results it is shown that the friction torque of valve train system quickly drops at a certain surface roughness of ceramic tappet shim and its value remains constant despite further smoothing.

• Journal of Power System Engineering
• /
• v.9 no.1
• /
• pp.50-56
• /
• 2005

The corrosion experiment was performed for 120 hours on the specimens in the natural seawater tank with four steps of the loaded torsional stress. The surface corrosion pattern of SCM440 area was showed global corrosion and narrow pitting, that was cause by galvanic corrosion between friction welded IN713LC and SCM440. But corrosion does not proceeded from IN713LC area. Initially, the average relative electrode potential and corrosion current were decreased suddenly, by and large, it was stabilized gradually tend to decreasing with the elapse of the immersion time. The corrosion rate was decreased by increasing the load stress, but 200 MPa specimen was showed most large value.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.11a
• /
• pp.184-189
• /
• 1999

This Paper presents the friction and lubrication charateristic related with oil aeration. It is well known that oil aeration occurs severe problem on lubrication system, in particular, in the engine bearings and hydraulic lash adjuster. In this study, engine tests were carried out in motoring conditions. In order to investigate oil aeration characteristics, we measured oil aeration with respect to oil temperature, oil viscosity, modified oil drain system. From the results, we concluded that aeration can be reduced by improving oil drain system and FMEP can be reduced by minimising of aeration.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.184-193
• /
• 2006

Rotation of intake and exhaust valves are very closely related to the long term durability of automotive engines. If the valves do not rotate even at a rated engine speed, it causes the uneven wear of the valve seat and valve head contact area, which eventually shortens the engine life. A principle of valve rotation mechanism was presumed based on some findings from experiments, and computer programs were developed to simulate the valve rotation phenomena. In this study we investigated the valve rotation mechanism by using the computer simulation models.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.35-46
• /
• 1990

The instantaneous friction in main bearings of a single cylinder diesel engine was determined by measuring the instantaneous angular velocity, calculating the resulting forces acting on the bearings, and solving the unsteady Reynolds equation in combination with the mobility method. The considered system consists of only the crankshaft with flywheel and oil pump. The thermal effects were not considered because of the short testing time. The tests were conducted using an electric start motor. The results indicated that when the bearing is not near equilibrium for very small speeds, simple film lubrication theories are not accurate. The details of grooves and unsteady terms in the Reynolds equation cannot be ignored for increasing efficiency of instantaneous friction calculation of the engine bearings. The effects of speed on instantaneous friction and energy lost in friction were determined.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.294-297
• /
• 2009

The frictional behaviors of Cermets/Cr-Ceramics and Cu-Al coatings of piston ring were investigated. Friction tests were carried out by pin-on-disk test and materials properties of coating layer were analyzed by nano indentation tester. Higher friction coefficient was obtained at harder coating with rougher surface. In case of hard-coating, the scratch depth, width and pile-up height had close relationship with indentation hardness. So the scratch width, depth and pile-up height increases with decreasing friction coefficient. But in case of soft-coating, the friction coefficients are strongly dependent on the morphological characteristics after nano scratching more than indentation hardness.

• Journal of Powder Materials
• /
• v.18 no.5
• /
• pp.417-422
• /
• 2011

Hydrophobic nanodiamond (ND) were dispersed in engine oil (Helix Oil, Shell co.) as an additives to improve tribology properties. In this study, nanodiamond prepared by an explosive method was used. Tribology properties of both pure Helix oil and engine oil containing ND additive were evaluated. The rotating disks were made of Gray Cast Iron (240 Hv) and SKD11 (710 Hv). Surface topographies of the disks' wear tracks and friction coefficient were compared. The results show that nanodiamond-dispersed lubricants are capable of reducing these metals' wear loss. The friction coefficient is strongly affected to the hardness of wear track.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.3 no.2
• /
• pp.231-243
• /
• 2000

This paper describes a simulation of secondary motion of piston assemblies using PISDYN by Ricardo. Motions of the piston, pin, rod and skirt are separately calculated, by integrating equations of motion for individual components and dynamic degrees of freedom. The effects of engine speed at full load and pin offsets on the piston assembly secondary motions, forces and friction were investigated in parametric study for 4-cylinder gasoline engine. Results show that lateral displacement and friction loss of the piston increase as a function of engine speed. The lateral motion of the piston is affected by the change in pin offset. The minimum friction loss for the condition of 4800rpm WOT occurs at a pin offset of 1.6mm.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.207-207
• /
• 2000

Fuel consumption of a modern combustion engine is significantly influenced by the mechanical friction losses. The reduction of the engine friction losses offers a remarkable potential in emission and fuel consumption reduction. The analysis of the engine friction distribution of modern engines shows that the piston and the cylinder have a high share at total engine friction. The present study uses PISDYN(by Ricardo) software to analyze the friction losses. The design parameters such as skirt profile, center of mass of the piston are shown to have key influences on the friction losses.