• Journal of the Korea Concrete Institute
• /
• v.23 no.6
• /
• pp.711-722
• /
• 2011

Beam-column gravity or Intermediate Moment frames subjected to unexpected large displacements are vulnerable when no seismic details are provided, which is typical. Conversely, economic efficiency of those frames is decreased if unnecessary special detailing is applied as the beam and column size becomes quite large and steel congestion is caused by joint transverse reinforcement in beam-column connections. Moderate seismic design is used in Korea for beam-column connections of buildings with structural walls, which are to be destroyed when the unexpected large earthquake occurs. Nonetheless, performance of such beamcolumn connections may be substantially improved by the addition of steel fibers. This study was conducted to investigate the effect of steel fibers in reinforced concrete exterior beam-column connections and possibility for the replacement of some joint transverse reinforcement. Ten half-scale beam-column connections with non-seismic details were tested under cyclic loads with two cycles at each drift up to 19 cycles. Main test parameters used were the volume ratio of steel fibers (0%, 1%, 1.5%) and joint transverse reinforcement amount. The test results show that maximum capacity, energy dissipation capacity, shear strength and bond condition are improved with the application of steel fibers to substitute transverse reinforcement of beam-column connections. Furthermore, several shear strength equations for exterior connections were examined, including the proposed equation for steel fiber-reinforced concrete exterior connections with non-seismic details.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.7
• /
• pp.37-47
• /
• 2017

In this study, a series of full-scale field tests on prebored and precast steel pipe piles and the corresponding numerical analysis have been conducted in order to study the characteristics of pile load-settlement relations and shear stress transfer at the pile-soil interface. Dynamic pile load tests (EOID and restrike) have been performed on the piles and the estimated design pile loads from EOID and restrike tests were analysed. Class-A type numerical analyses conducted prior to the pile loading tests were 56~105%, 65~121% and 38~142% respectively of those obtained from static load tests. In addition, design loads estimated from the restrike tests indicate increases of 12~60% compared to those estimated in the EOID tests. The EOID tests show large end bearing capacity while the restrike tests demonstrate increased skin friction. When impact energy is insufficient during the restrike tests, the end bearing capacity may be underestimated. It has been found that total pile capacity would be reasonably estimated if skin friction from the restrike tests and end bearing capacity from the EOID are combined. The load-settlement relation measured from the static pile load tests and estimated from the numerical modelling is in general agreement until yielding occurs, after which results from the numerical analyses substantially deviated away from those obtained from the static load tests. The measured pile behaviour from the static load tests shows somewhat similar behaviour of perfectly-elastic plastic materials after yielding with a small increase in the pile load, while the numerical analyses demonstrates a gradual increase in the pile load associated with strain hardening approaching ultimate pile load. It has been discussed that the load-settlement relation mainly depends upon the stiffness of the ground, whilst the shear transfer mechanism depends on shear strength parameters.

• Korean Journal of Agricultural Science
• /
• v.6 no.1
• /
• pp.56-64
• /
• 1979

Two types of fiat-plate collector were designed and constructed for utilizing the solar energy as heating source of red pepper drying. It was performed to investigate the basic factors on using the collectors and the drying effect on various types of red pepper, and the results obtained are summarized as follows. 1. The optimum tilted angles of the collector in Daejeon area were ${\phi}-15^{\circ}$ in summer season and ${\phi}+15^{\circ}$ in winter season when it was adjusted two times per a year: 2. In the conditions during experiment period, average atmospheric temperature and relative humidity were $25.6^{\circ}C$ and 52.6%, respectively, and $42.0^{\circ}C$, 74.2% in the control chamber. The temperature in the drying chamber connected to the water heater was the highest but relative humidity in the chamber connected to the air heater was the lowest among the chambers. 3. The drying velocity of whole red pepper in the chamber connected to the water heater was the fastest as 2.3 times as compared to the whole type on the mat drying followed by air heater and control in decreasing order. The horizontally cut red pepper in the chamber connected to the water heater was dried exceedingly fast among twelve plots. 4. The content of capsaicine as pungent principle and of capsanthine as red pigment in the red pepper were reduced during drying but there were no differences significantly on the drying method, and it could not affect much on the quality of dried product.

• Journal of Bio-Environment Control
• /
• v.29 no.2
• /
• pp.161-170
• /
• 2020

There is systematic spatial variations in environmental properties due to sensitive reaction to external conditions at plastic greenhouse occupied 99.2% of domestic agricultural facilities. In order to construct 3 dimensional distribution of temperature, relative humidity, CO₂ and illuminance, measurement matrix as 3 by 3 by 5 in direction of width, height and length, respectively, dividing indoor space of greenhouse was designed and tested at experimental site. Linear regression analysis was conducted to evaluate optimal estimation method in terms with horizontal and vertical variations. Even though sole measurement point for temperature and relative humidity could be feasible to assess indoor condition, multiple measurement matrix is inevitably required to improve spatial precision at certain time domain such as period of sunrise and sunset. In case with CO₂, multiple measurement matrix could not successfully improve the spatial predictability during a whole experimental period. In case with illuminance, prediction performance was getting smaller after a time period of sunrise due to systematic interference such as indoor structure. Thus, multiple sensing methodology was proposed in direction of length at higher height than growing bed, which could compensate estimation error in spatial domain. Appropriate measurement matrix could be constructed considering the transition of stability in indoor environmental properties due to external variations. As a result, optimal measurement matrix should be carefully designed considering flexibility of construction relevant with the type of property, indoor structure, the purpose of crop and the period of growth. For an instance, partial cooling and heating system to save a consumption of energy supplement could be successfully accomplished by the deployment of multiple measurement matrix.

• The Korean Journal of Malacology
• /
• v.20 no.2
• /
• pp.111-120
• /
• 2004

We investigated the reproductive cycle of Corbicula japonica with its gonadal development by histological observations, and the seasonal changes in biochemical mass and foot muscle of the adductor muscle, visceral mass and foot muscle of the clam by biochemical analysis, from January to December, 2003. The reproductive cycle of this species can be classified into five successive stages: early active stage (February to April), late active stage (April to July), ripe stage (June to August), partially spawned stage (July to September) and spent/inactive stage (September to March). According to ANOVA test, there were significant differences (p < 0.05) in total protein, total lipid and glycogen contents among months for all of the visceral mass, adductor muscle and foot muscle. Total protein content was highest in adductor muscle, while lowest in visceral mass. There was no correlation in total protein content between visceral mass and adductor muscle (p = 0.208). However, strong positive correlation was found between adductor muscle and foot muscle (r = 0.769, p < 0.001). In visceral mass, total lipid content was the highest; it was 2 or 3-fold higher than in adductor muscle or foot muscle. The monthly change was also most dynamic in visceral mass. It decreased from January to March (early active stage), and reached maximum in April (late active stage). From May to August (ripe and partially spawned stage), it dradually decreased and then increased again until October (spent/inactive stage). Multiple comparisons showed that total lipid content in visceral mass between all of the adjacent two months was significaltly different (p < 0.05). There were strong negative correlations in total lipid content between visceral mass and adductor muscle (r = 0.687, p < 0.001), and between visceral mass and foot muscle (r = 0.473, p = 0.008). Changes of glycogen content were more or less similar to the changes of lipid contents in visceral mass, adductor muscle and foot muscle, except for April. In April, glycogen content in visceral mass was over four times higher than that in adductor muscle or foot muscle. There was a positive correlation in glycogen content between adductor muscle and foot muscle (r = 0.686, p < 0.001). Especially, total lipid content showed a negative correlation between the adductor muscle and visceral mass. Therefore, these results indicate that the nutrient content of the adductor muscle, visceral muscle and foot muscle changed in response to gonadal energy needs.

• Progress in Medical Physics
• /
• v.23 no.2
• /
• pp.114-122
• /
• 2012

For the determination of absorbed dose to water from a linear accelerator photon beams, it needs a exposure calibration factor $N_x$ or air kerma calibration factor $N_k$ of air ionization chamber. We used the exposure calibration factor $N_x$ to find the absorbed dose calibration factors of water in a reference source through the TG-21 and TRS-277 protocol. TG-21 used for determine the absorbed dose in accuracy, but it required complex calculations including the chamber dependent factors. The authors obtained the absorbed dose calibration factor $N_{dw}{^{Co-60}}$ for reduce the complex calculations with unknown $N_{dw}$ only with $N_x$ or $N_k$ calibration factor in a TM31010 (S/N 1055, 1057) ionization chambers. The results showed the uncertainty of calculated $N_{dw}$ of IC-15 which was known the $N_x$ and $N_{dw}$ is within -0.6% in TG-21, but 1.0% in TRS-277. and TM31010 was compared the $N_{dw}$ of SSDL to that of PSDL as shown the 0.4%, -2.8% uncertainty, respectively. The authors experimented with good agreement the calculated $N_{dw}$ is reliable for cross check the discrepancy of the calibration factor with unknown that of TM31010 and IC-15 chamber.

• Journal of Life Science
• /
• v.17 no.6 s.86
• /
• pp.836-840
• /
• 2007

This study was conducted to investigate mineral contents of commercial powdered infant formula for obtaining basic data on infant nutrition. 11 Commercial infant formula based on cow's milk were collected and the contents of macro minerals (calcium, phosphorous, sodium, potassium and magnesium) and trace minerals (iron, zinc and copper) were compared with Dietary Reference Intakes for Koreans (KDRIs). The overall mineral contents in 100 g and in 100 kcal of infant formula satisfied the recommended formula regulation and Codex. In infant formula during 0-5 monthly age, calcium, phosphorous, sodium, potassium, magnesium, zinc and copper could supply 233.1%, 273.5%, 156.7%, 142.0%, 150.8%, 209.3%, 171.1% of recommended daily mineral intakes, respectively. The content of iron in 0-5 monthly age formula supplied2842.6% of recommended daily iron intakes. In infant formula during 6-11 monthly age, calcium, phosphorous, potassium, magnesium, iron, zinc and copper satisfied their recommended daily intakes. However, sodium only supplied 76.6% of its recommended daily intake. Intake ratio between Ca/P, Ca/Mg, Ca/Fe, Na/K and Zn/cu in infant formula during 0-5 monthly age were 1.7±0.2, 11.0±2.4,64.9±10.0, 0.3±0.1, and 9.6±1.0, respectively. Intake ratio between Ca/P, Ca/Mg, Ca/Fe, Na/K and Zn/cu in infant formula during 6-11 monthly age were 1.7${\pm}$0.2, 12.9${\pm}$1.5, 80.1${\pm}$13.8, 0.3, and 9.4${\pm}$1.1,respectively. From this study, evaluation of mineral contents of commercial infant formula was established, which could strengthen the basic information on infant nutrition.

• Economic and Environmental Geology
• /
• v.44 no.3
• /
• pp.229-238
• /
• 2011

S-wave, which provides lithology and pore fluid information, plays a key role in estimating gas-hydrate saturation. In general, P- and S-wave velocities increase in the presence of gas-hydrate and the P-wave velocity decreases in the presence of free gas under the gas-hydrate layer. Whereas there are very small changes, even slightly increases, in the S-wave velocity in the free gas layer because S-wave is not affected by the pore fluid when propagating in the free gas layer. To verify those velocity properties of the BSR (bottom-simulating reflector) depth in the gas-hydrate prospect area in the Ulleung Basin, P- and S-wave velocity profiles were derived from multi-component ocean-bottom seismic data which were acquired by Korea Institute of Geoscience and Mineral Resources (KIGAM) in May 2009. OBS (ocean-bottom seismometer) hydrophone component data were modeled and inverted first through the traveltime inversion method to derive P-wave velocity and depth model of survey area. 2-D multichannel stacked data were incorporated as an initial model. Two horizontal geophone component data, then, were polarization filtered and rotated to make radial component section. Traveltimes of main S-wave events were picked and used for forward modeling incorporating Poisson's ratio. This modeling provides S-wave profiles and Poisson's ratio profiles at every OBS site. The results shows that P-wave velocities in most OBS sites decrease beneath the BSR, whereas S-wave velocities slightly increase. Consequently, Poisson's ratio decreased strongly beneath the BSR indicating the presence of a free gas layer under the BSR.

• Journal of KIISE:Information Networking
• /
• v.30 no.3
• /
• pp.329-342
• /
• 2003

Most of the existing multicast routing protocols for ad-hoc networks do not take into account the efficiency of the protocol for the cases when there are large number of sources in the multicast group, resulting in either large overhead or poor data delivery ratio when the number of sources is large. In this paper, we propose a multicast routing protocol for ad-hoc networks, which particularly considers the scalability of the protocol in terms of the number of sources in the multicast groups. The proposed protocol designates a set of sources as the core sources. Each core source is a root of each tree that reaches all the destinations of the multicast group. The union of these trees constitutes the data delivery mesh, and each of the non-core sources finds the nearest core source in order to delegate its data delivery. For the efficient operation of the proposed protocol, it is important to have an appropriate number of core sources. Having too many of the core sources incurs excessive control and data packet overhead, whereas having too little of them results in a vulnerable and overloaded data delivery mesh. The data delivery mesh is optimally reconfigured through the periodic control message flooding from the core sources, whereas the connectivity of the mesh is maintained by a persistent local mesh recovery mechanism. The simulation results show that the proposed protocol achieves an efficient multicast communication with high data delivery ratio and low communication overhead compared with the other existing multicast routing protocols when there are multiple sources in the multicast group.

• Journal of radiological science and technology
• /
• v.39 no.1
• /
• pp.99-105
• /
• 2016

The noise power spectrum (NPS) is one of the most general methods for measuring the noise amplitude and the quality of an image acquired from a uniform radiation field. The purpose of this study was to compare different NPS methodologies by using megavoltage X-ray energies. The NPS evaluation methods in diagnostic radiation were applied to therapy using the International Electro-technical Commission standard (IEC 62220-1). Various radiation therapy (RT) devices such as TrueBeam$^{TM}$(Varian), BEAMVIEW$^{PLUS}$(Siemens), iViewGT(Elekta) and Clinac$^R$ iX (Varian) were used. In order to measure the region of interest (ROI) of the NPS, we used the following four factors: the overlapping impact, the non-overlapping impact, the flatness and penumbra. As for NPS results, iViewGT(Elekta) had the higher amplitude of noise, compared to BEAMVIEW$^{PLUS}$ (Siemens), TrueBeam$^{TM}$(Varian) flattening filter, Clinac$^{R}$iXaS1000(Varian) and TrueBeam$^{TM}$(Varian) flattening filter free. The present study revealed that various factors could be employed to produce megavoltage imaging (MVI) of the NPS and as a baseline standard for NPS methodologies control in MVI.