• 한국ITS학회 논문지
• /
• 제8권6호
• /
• pp.180-186
• /
• 2009

DC/DC 컨버터 등의 전력변환장치와 같은 비선형부하에 대해 알루미늄 전해 커패시터는 에너지의 일시적 저장이나 전압 평활용으로 많이 사용되고 있다. 그러나 전해 커패시터는 사용 시간이 늘어나면서 온도 상승 및 전해액(electrolyte)의 증발 등으로 인하여 고장이 매우 빈번하게 나타난다. 따라서 본 논문에서는 이러한 사고에 대한 고장모드를 분류하고 이를 진단하기 위한 사전 단계로 전해 커패시터의 주파수 변화에 따른 특성 해석과 이를 바탕으로 한 커패시턴스 용량 추정 알고리즘을 제안하였다. 기본파에 해당하는 저주파의 주파수 분석 결과에 따른 모의 실험의 결과는 제안한 알고리즘의 타당성을 입증하였다.

• 전력전자학회논문지
• /
• 제14권6호
• /
• pp.481-487
• /
• 2009

슈퍼커패시터를 이용하여 철도 차량의 가 감속 시에 발생하는 DC 가선전압의 변동을 안정화하는 방법을 제안하였다. 이를 위해서 슈퍼커패시터를 서로 다른 3개의 시정수를 가지는 전압가변 정전용량을 가지는 RC회로로 가정하고 실험적인 방법으로 파라미터 값을 결정하여 전기적인 모델링을 수행하였다. 슈퍼커패시터를 이용한 에너지 저장장치를 구성하여 시뮬레이션 및 실험을 통하여 제안된 모델을 검증하고 제어기를 설계하였다. 그리고, 경산 시험선에서 실증시험을 수행하고 경제성을 평가하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.514-520
• /
• 2001

A 300Wh class flywheel energy storage system using high Tc superconductor bearings(HTC SFES) is being developed by KIMM and KEPRI. HTC SFES consists of a flywheel rotor, superconductor bearings, a motor/generator and its controller, touch-down bearings, vacuum chamber, etc. Stiffness and damping values of superconductor bearings were experimentally estimated to be 67,700N/m and 29Ns/m respectively. The present HTC SFES was designed to have maximum operating speed of 33000 rpm, which is far above 2 rigid body mode critical speeds of 645rpm and 1,275rpm. Leaf-spring type touch-down bearing were utilized to have the system pass safely through the system critical speeds. It has been experimentally verified that the system can run stably up to 28,000 rpm so that HTC SFES is now expected to reach up to its maximum design speed of 33,000rpm without any difficulties. The Halbach array motor & generator has also been proven its effectiveness on transferring electrical energy to a rotaing composite flywheel in kinetic form.

• Progress in Superconductivity
• /
• 제13권3호
• /
• pp.195-202
• /
• 2012

In this paper, we designed Active Magnetic Bearing (AMB) for large scale Superconductor Flywheel Energy Storage System (SFESS) and PD controller for AMB. And we experimentally evaluated SFESS including hybrid type AMB. The radial AMB was designed to provide force slew rate that was sufficient for the unbalance disturbances at the maximum operating speed. The thrust AMB is a hybrid type where a permanent magnet carries the weight of the flywheel and an electromagnetic actuator generates the dynamic control force. We evaluated the design performance of the manufactured AMB through comparison of FEM analysis and the results of experimental force measurement. In order to obtain gains of PD controller and design a notch filter, the system identification was performed through measuring frequency response including dynamics for the AMBs, a power amp and a sensor using a sine swept test method after levitating the flywheel. Through measuring the current input of the AMBs and the orbit of a flywheel according to rotational speed, we verified excellent control performance of the AMBs with small amount current for the large scale SFESS.

• 전기학회논문지
• /
• 제64권7호
• /
• pp.992-998
• /
• 2015

The ESS is composed of Battery Package, PCS(Power Conditioning System) Package, BCU(BESS Control Unit). In Jeju smart grid test-bed, we have developed a business model by ESS power system, renewable energy, transportation, such as customers, and have demonstrated above things. We have analyzed the EMS(Energy Management System) model of KPX where manages supply and demand of domestic electrical power system. We modified and launched EMS for microgrid but the cost was expensive and the system was large size. For releasing this system from industry as a whole, it is imperative to develop PMS(Power Management System) for microgrid. However, the cost of EMS for microgrid is expensive, some systems because it is a large development of the all of the first fruits in urgent PMS(Power Management System) for microgrid to be used in industry in general. Therefore, in this paper, we propose the ESS model considering the power systems characteristics and extensibility in korea. and also we propose the PMS to manage the ESS systems.

• 조명전기설비학회논문지
• /
• 제28권8호
• /
• pp.106-112
• /
• 2014

This paper presents the analysis of connected operation of photo voltaic source and Li energy storage system. The micro-grid has been installed and operated for several years at the campus of USF and has been a role of test bed. Photo voltaic source has been strongly influenced by the location, weather and climate of a installed area and Li battery is connected directly to the photo voltaic source to compensate for the limitations. The Li battery is operated to supply power output to the grid by the charging or discharging mode based on the average power output of the PV source which is calculated from monitored data for several years. The load of the PV and Li battery system is operated as a severe loading condition and the operating characteristics of PV source and Li battery are analyzed in detail. In connected operations of PV and Li battery to power system, the PV and Li battery is operated to supply constant power during only day time or peak time to increase load shedding ratio and efficient usage of generation sources in power system.

• 전력전자학회논문지
• /
• 제22권4호
• /
• pp.312-323
• /
• 2017

This paper introduces the bidirectional dc-dc converter design case study, which employs silicon-carbide (SiC) MOSFETs for battery energy storage system (BESS). This converter topology is selected as bidirectional synchronous buck converter, which is composed of a half bridge converter, an inductor, and a capacitor, where the converter has less conduction loss than that of a unidirectional buck and boost converter, and to improve the converter efficiency, both the power stage design and power conversion architecture are described in detail. The conduction and switching losses are compared among three different SiC devices in this paper. In addition, the thermal analysis using Maxwell software of each switching device supports the loss analyses, in which both the 2 kW prototype analyses and experimental results show very good agreement.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.283-289
• /
• 1997

A 500Wh class high-speed Flywheel Energy Storage System (FESS) driven by a built-in BLDC motor/generator has been designed, which runs from 30000 to 60000rpm nominally. Due to the motor/generator inside, the flywheel rotor made of composites supported by PM/EM hybrid bearing system has a shape of bell or pendulum and thus requires accurate rotordynamic analyses and prediction of its dynamic behavior to secure the operating reliability. Rotordaynamic analyses of the flywheel rotor-bearing system revealed that the bell shaped rotor has two conical rigid-body modes in the system operating range and the first conical mode, of which nodal point lies in the radial EM bearing position, can adversely affect the dynamic response of the rotor at the corresponding critical speed. To eliminate the possibility of wild behavior of the rotor, two guide bearings are adopted at the upper end of the rotor and motor/generator. It was also revealed that the EM bearing stiffness of 0.5~1.0E+6 N/m and damping of 2000 Ns/m are favorable for smooth operation of the system around the 2nd critical speed.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.511-511
• /
• 2012

핵 융합로는 고밀도, 고에너지 플라즈마에 지속적으로 노출되며 고열부하 및 중성자, 플라즈마 이온에 의한 물성변화에 대한 다양한 핵 융합로 구축 재질의 실험데이터가 요구된다. 특히 핵 융합 반응의 핵심연료인 삼중수소의 재질별 누설거동 특성은 삼중수소의 블랑켓에서의 증식율, 열 교환기 및 공급과 회수과정에서의 손실율, 저장, 취급 및 차폐 등의 계산에 활용되므로 핵 융합로의 안전성과 경제성 확보 측면에서 매우 중요하다. 따라서 핵 융합로 구축 재질 선정시 삼중수소의 누설거동 특성은 반드시 고려되어야 한다. 본 연구는 삼중수소 누설거동 특성 해석을 위한 기초실험으로, 수소동위원소를 사용하는 누설거동실험 장치를 설계 제작하여 누설 거동실험을 수행하였다. 누설 가스로는 수소를 사용하였고, 시편은 스테인레스 스틸(SUS-304)을 사용하였으며, 시편의 가열온도는 500, 600, 700, $800^{\circ}C$에서 각각 수소누설거동 실험을 실시하였다. 수소에 대한 SUS-304 재질의 permeability, diffusivity, solubility에 대한 실험 결과를 발표하고자 한다.

• 한국전기전자재료학회논문지
• /
• 제20권2호
• /
• pp.135-141
• /
• 2007

The conduction-cooled HTS SMES is operated in cryogenic and high vacuum condition. Thus, Insulation design at cryogenic temperature and high vacuum is a key and an important element that should be established to accomplish miniaturization that is a big advantage of HTS SMES. However, the behaviors of insulators for cryogenic conditions in vacuum are virtually unknown. Therefore, we need active research and development of insulation concerning application of the conduction-cooled HTS SMES. Therefore, in this study, we experimented about insulation characteristic high vacuum and cryogenic similar to driving condition of SMES system. Also, investigated about insulation characteristic of suitable some materials to insulator for conduction-cooled HTS SMES. As this results, we possessed basis data for insulation materials selection and insulation design for development of 600 kJ class conduction-cooled HTS SMES.