• Journal of the Korean earth science society
• /
• v.39 no.1
• /
• pp.89-102
• /
• 2018

We analyzed the meteorological and radiation characteristics of Seoul metropolitan area using data from energy flux towers that were installed and operated by the Weather Information Service Engine (WISE). The meteorological and radiation variables included temperature, pressure, wind speed, wind direction, relative humidity, surface temperature, rainfall amount, upward and downward solar radiation, upward and downward longwave radiation, albedo and emissivity from 14 energy flux stations located in the Seoul metropolitan area from July 2016 to July 2017. According to the monthly data during the period, the albedo is low and emissivity is high at the Jungnang station in the urban and opposite at Bucheon station in the suburban area. For a station in natural state, the albedo was higher than urban stations because solar radiation reflects effectively. Relatively high temperatures were shown at stations located in urban area with low albedo and high emissivity, in general. However, temperature was high at Gajwa and Ttukseom stations, the albedo was relatively high due to the station environment surrounded by glass wall buildings and the Han river. In the station located in suburban area, both emissivity and temperature were low. Among these stations, Bucheon station had the highest emissivity values because the surface temperature was relatively lower than that of the suburban area. As a result, the albedo decreased and the emissivity increased at stations in urban areas. Additionally, Seoul metropolitan area had less than $100Wm^{-2}$ of net radiation, which implied that radiation energy could be absorbed in the atmosphere.

• Composites Research
• /
• v.21 no.4
• /
• pp.7-14
• /
• 2008

Prediction of the load-bearing capacity of an adhesive-bonded Joint is of practical importance for engineers. This paper introduces interface fracture mechanics approach to predict the load-bearing capacity of composite metal bonded joints. The adhesion strength of composite/steel bonding is evaluated in terms of the energy release rate of an interfacial crack and the fracture toughness of the interface. Virtual track closure technique (VCCT) is used to calculate energy release rates, and hi-material end-notched flexure (ENF) specimens are devised to measure the interfacial fracture toughness. Bi-material ENF specimens gave consistent mode II fracture toughness $(G_{IIc})$ values of the composite/steel interface regardless of the thickness of specimens. The critical energy release rates of double-lap joints showed a good agreement with the measured fracture toughness. Therefore. the energy-based interfacial fracture characterization can be a practical engineering tool for predicting the load-bearing capacity of bonded joints.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.12
• /
• pp.2072-2078
• /
• 2003

In this paper, the boundary element analysis of viscoelastic strain energy release rate G(t) for the cracked linear viscoelastic solids has been attempted. This study proposes the G(t) equation and the calculating method of G(t) by time-domain boundary element analysis for the viscoelastic solids. The G(t) is defined as the derivative of the viscoelastic potential energy II(t) with respect to crack length a. Two example problems are presented to show the applicability of the proposed method to the analysis of the cracked linear viscoelastic solids. Numerical results of example problems show the accuracy and effectiveness of the proposed method.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.5
• /
• pp.911-920
• /
• 1989

It this study, beam-type bend specimen is used to evaluate the interlaminar fracture toughness of laminated composite under mixed-mode deformations. The specimen is loaded under three-point bending and hence produced mixed-mode deformations in the vicinity of the crack tip according to the variation of the thickness ratio on delamination plane. Total energy release rate is obtained by elementary beam theory considering the effect of shear deformation. The partitioning of total value into mode-I and mode-II components is also performed. The mixed-mode interlaminar fracture toughness is evaluated by experiments on specimens with several thickness ratios of delamination plane. As the part of delamination plane is thicker, the effect of shear deformation on total energy release rate is increased. Beam-type bend specimen men may be applied to obtain informations on the mixed-mode interlaminar fracture behavior of laminated composites.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.1
• /
• pp.97-107
• /
• 1995

Global postbuckling analysis is accomplished for one-dimensional and two-dimensional delaminations. A new finite element model, which can be used to model the global postbuckling analysis of one-dimensional and two-dimensional delaminations, is presented. In order to calculate the strain energy release rate, geometrically nonlinear analysis is accomplished, and the incremental crack closure technique is introduced. To check the effectiveness of the finite element models and the incremental crack closure technique, the simplified closed-form sloution for a through-the-width delamination with plane strain condition is derived and compared with the finite element result. The finite element results show good agreement with the closed-foul1 solutions. The present method was extended to calculate the strain energy release rate for two-dimensional delamination. For a symmetric circular delamination, the strain energy release rate shows great variation along the delamination front. and the delamination growth appears to occur perpendicular to the loading direction.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.9 s.180
• /
• pp.2174-2183
• /
• 2000

In this paper, the evaluation method of interfacial fracture toughness to apply the fracture toughness was investigated in adhesively bonded joints of AI/Ced./A1. Four types of adhesively bonded double-cantilever beam(DCB) joints with the interface crack were prepared for the test of interfacial fracture toughness. The experiments to measure the interfacial fracture toughness were performed under the various mixed-mode conditions. The critical energy release rate, Gc, was obtained by the experimental measurement of compliances. From the experimental results, the interfacial fracture toughness for the mixed-mode specimens is well characterized by the energy release rate, and the method of strength evaluation by the interfacial fracture toughness was discussed in adhesively bonded joints.

• Computational Structural Engineering
• /
• v.7 no.2
• /
• pp.111-120
• /
• 1994

Cracks in rubber bonded to a rigid material such as steel are analyzed with the aid of a mixed finite element technique. Firstly the weak form is derived for finite element analysis of an incompressible material, and the Mooney-Rivlin form is assumed for the constitutive modeling of rubber. The numerical results from finite element analysis is examined to confirm the accuracy and convergence of solution by way of comparison to other numerical results. The interpretation of the J-integral for large elastic deformation as the energy release rate is confirmed, and the J-integral is calculated for varing crack length. The crack growth stability is discussed using the result of finite element analysis.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.149.2-149.2
• /
• 2014

진공용기를 배기하기 시작하면 짧은 시간 동안은 공기의 배기가 주를 이루지만 그 후에는 표면 방출 기체의 배기가 이어지고 표면방출 기체의 대부분은 물이라는 것은 누구나 알고 있는 사실이다. 그러나 배기 계산을 할 때는 막상 물 보다는 공기의 일부로 생각하거나 수분을 다른 기체들과 유사하게 다루는 것에 익숙해져 있다. 이런 계산 결과는 실제 상황을 재현하지 못할 뿐만 아니라 일반적으로 배기능력을 과대평가하게 만들어서 공정 계획대로 진공 시스템을 운전하는 것을 불가능하게 만든다. 물은 일반적인 기체와는 성격이 아주 다르다. 다른 기 체 분자들의 흡착 에너지가 ~0.3 eV이고 기름분자가 ~1 eV 정도인 것에 반해 물은 0.55 eV 내외로 상온에서도 비교적 흡착을 잘하고 또 적당히 방출도 일어나는 특별한 특성 때문에 용기 압력을 지배하면서도 신속한 배기를 방해한다. 만일 이런 물의 흡착률 및 방출률을 제대로 수치화할 수 있다면 배기 계산을 훨씬 현실화할 수 있다. 물의 흡착률은 물분자의 부착계수가 지배하고 방출률은 체류시간에 의해 결정되지만 표면상태에 따라 천차만별이므로 얼마라고 확정하기 어렵다. 우선 이번에는 물의 부착계수 최대값을 0.1 정도로 잡고 흡착량에 따라 직선적으로 줄어드는 것으로 가정하며, 물의 표면 체류시간도 몇 가지 값으로 가정해서 0-D 입자 평형 계산을 수행하여 특정 시스템에서 얻은 실험 결과와 비교하려고 한다. 앞으로 몬테카를로 방법과 연계하여 3차원적 분석을 할 수 있는 코드로 발전시켜 나갈 예정이다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.213-214
• /
• 2008

• Nuclear industry
• /
• v.20 no.6 s.208
• /
• pp.31-44
• /
• 2000

본 연구에서 액체금속로의 노심용융(core meltdown)으로 인한 초 즉발 임계(super-prompt critical)의 출력 폭주 사고시, 노심의 반응도 및 열수력 특성 변화와 에너지 방출량등을 계산하기 위하여, Bethe-Tait 방버론을 수정, 보완한 분석 모델이 개발되었다. 주요 보완 내용으로서는, 금속 연료 노심의 단상 액체 영역에서의 선형의(Linear) threshold 형태의 상태 방정식뿐만 아니라 포화 증기(saturated fuel vapor) 영역에서의 상태 방정식이 개발되었고, 이에 따른 노심 붕괴 반응도(disassembly reactivity)의 분석 모델이 개발되었다. 또한 도플러 반응도 효과를 고려하기 위한 분석모델도 아울러 개발되었다. 상기 보완 모델을 실행할 수 있는 수치 해석 프로그램이 개발되었고, 이를 활용하여 KALIMER에서 HCDA가 발생하였을 경우 노심에서의 에너지 방출량 계산이 수행되었다. 분석결과 도플러 효과와 포화 증기 영역에서의 압력 증가 및 노심팽창의 중요성이 확인되었다. 도플러 효과가 고려되지 않을 경우 HCDA는 분석된 모든 반응도 삽입률에 대하여 폭발적인 에너지 방출과 함께 사고가 종결되는 것으로 평가되었다. 그러나 도플러 상수가 최적 평가치인 -0.002인 경우 50$/s이하의 반응도 삽입률에서는 노심은 비등점(0.8KJ/g)에 도달치 않았으며, 설계 기준 사고인 100$/s의 경우에도 노심은 포화 증기 영역에 머물고 압력이 급격히 증가하는 단상(single phase)액체 영역의 threshold 값에 미치지 않기 때문에 사고는 핵연료 증기(vapor)의 점진적인 분산과 함께 종결되는 것으로 분석되며, 총 에너지 발생량은 약 1,800MJ로서 기계적 손상 에너지로 전환되는 분율을 고려할 때 KALIMER 원자로 용기의 구조 설계 기준치에 비해 상당한 여유도를 갖는 것으로 평가되었다.