• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1103-1106
• /
• 2005

The research and development for LPLI system to replace the conventional LPG fuel supply system has been processed with a view to enhancing the environmental status and the efficiency for LPG cars. Part of the small sized cars are under commercialization with the LPLI application already. And yet, most of the technologies are relied upon the advanced countries and as part of the application for large scaled engines, many researches are on the increase. This study shows the technology development to make use of LPLI system for those large engines and reviews the controllers, which were manipulated through experiments for their work, reliability and possibility for commercialization.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.1
• /
• pp.28-35
• /
• 2005

Fuel injection rate of an injector is affected by various injection conditions such as injection duration, fuel temperature, injection pressure, and voltage in LPG liquid injection systems for either a port-fuel-injection(PFI) or a direct injection(DI) in a cylinder. Even fuel injection conditions are changed, the air-fuel ratio should be accurately controlled to educe exhaust emissions. In this study, correction factor for the fuel injection rate of an injector is derived from the density ratio and the pressure difference ratio. A voltage correction factor is researched from injection test results on an LPG liquid injection engine. A compensation method of the fuel injection rate is proposed for a fuel injection control system. The experimental results for the LPG liquid injection system in a SI-engine show that this system works well on experimental range of engine speed and load conditions. And the fuel injection rate is accurately controlled by the proposed compensation method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.87-94
• /
• 2003

Recently, LPLi(Liquied-Phase LPG injection) system is studied for the new stringent emission regulations. But , there are some problems to be solved such as injector tip icing and fuel leakage for LPLi system development. In this paper, the icing problem near injector tip which leads to difficulty of accurate A/F control was studied and reported. Icing of injector tip and port wall was observed at all the cases in this study regardless of injection duration and angle, air humidity change. The spray angle of LPLi was observed approximately two times wider than that of Gasoline injection. This makes the LPLi spray collide with intake port around injector tip. Temperature of the wetted area was decreased and icing of water vapor contained in intake air because of evaporation of the fuel film. The ice of the injector tip and port wall is also affected by the materials related to heat transfer.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.39-44
• /
• 2004

As air pollution has become an important issue across the world, studies of clean fuel are on going to reduce combustion emissions. One example is development of the LPLi(Liquefied Phase LPG injection) engine. Some problems are occurred during development. One of the problems is icing phenomenon at injector tip due to evaporation potential heat when liquid LPG is injected. If the Icing is raised at injector tip or injector inserting hole, it disturbs fuel injection. And if the ice particles are inducted into cylinder, it brings problems associated with control of emission and air/fuel ratio. In order to solve the problems, a rig system was set up and observed Icing of injector tip. Engine test was carried out for visualization of injector tip icing and its effects on combustion and emissions.

• Journal of ILASS-Korea
• /
• v.9 no.4
• /
• pp.46-52
• /
• 2004

An LPG engine (KL6i) for heavy duty vehicle has been developed using liquid phase LPG injection (LPLi) system, which has regarded as one of next generation LPG fuel supply systems. For the KL6i engine, lean burn technology was introduced to minimize the thermal loading and NOx emissions due to an increase of the engine power. In this work, injection timing and piston bowl shape were investigated for the stabilization of lean burn characteristics. Experimental results reveals that fuel stratification induced by these parameters is most effective strategy to extend lean combustion limit in the LPLi system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.30-37
• /
• 2007

The injection and spray characteristics of top-feed type injector was investigated under liquid phase injection fueled with liquefied petroleum gas (LPG). Different pressures and temperatures of fuel injection system were tested to identify the injection characteristics after hot soaking. MIE-scattering technique was used for verification of successful liquid phase injection after hot soaking. In case of bottom-feed type injector, the injection was accomplished at every experimental condition. In case of top-feed type injector, when the pressure of LPG was over 1.2 MPa, the injection was not executed. However, under the pressure were 1.2 MPa, the liquid phase injection after hot soaking was accomplished. The engine with top-feed type fuel injection equipment was restarted successfully after hot soaking.

• Journal of ILASS-Korea
• /
• v.16 no.3
• /
• pp.146-151
• /
• 2011

LPG(Liquified Petroleum Gas) fuel for vehicles has lots of advantages such as low emission level, cheaper fuel cost and enough infrastructure. Therefore it arouses interest as an alternative engine to reduce emission of diesel engines. Especially MPI(Multi Point Injection) type LPLi(Liquid Phase LPG injection) system could have overcome the disadvantages of mixer types such as low engine performance, decreased charging efficiency and cold starting difficulty. However ice formation on the nozzle tip and intake port due to the freezing of moisture around the components is often observed in LPLi systems. This icing phenomenon is the direct cause of unstable engine combustion, resulting in engine emissions. Therefore in this research, a spray visualization test for LPG injection was carried out to obtain the basic information of an LPLi injector, then the effects of butane and propane mixing rates on ice formation at the intake port and nozzle tip was investigated. As a result, the icing characteristics of them showed contrary results according to the mixing rates.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.5
• /
• pp.90-97
• /
• 2002

The interaction between airflow and liquid phase LfG (Liquefied Petroleum Gas) sprays was investigated in a steady flow system embodied in a wind tunnel to simulate the variety of flow inside intake port of LPG engines with liquid injection system. The spray developments in flowing fields with the mean velocities of 5.4, 21.5 and 42.4m/s were identified by spray visualization techniques such as Mie scattering and shadowgraph. The microscopic visualization using a telescopic lens system was performed to investigate the shape and size of liquid droplets in the spray. PDA measurement was used to get 1-dimensional velocity and diameter of liquid droplets. The fast co-flows make the spray field be compact and be lead upward to the injection direction. SMD of the spray was smaller at the fast flowing field. Spray width got bigger and SMD of the spray was smaller with higher injection pressure.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3323-3328
• /
• 2007

Conventional LPG pump for Liquified Petroleum injection(LPi) engine has been adopted vane type. But the BLDC type fuel pump for LPi system has complicated structure and its price is high. Therefore, as a alternative, this study has mainly focused on the development of turbine type LPG pump which has lower cost and simple structure than conventional BLDC type. To verify the possibility of substitute the performance tests were performed for each fuel pump. The comparative items were pressure settling time, variation of fuel outlet temperature and engine performance of hot restart ability. As a result, performances of turbine type LPG pump were equivalent or high comparing to the BLDC type all over the tests for different fuel composition.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.77-84
• /
• 2002

For the purpose of obtaining a fundamental data which is needed to develope the port injection type charged LPLi engine system, we manufactured intake port injection system of liquid charging LPG and modified heavy duty single cylinder LPLi engine from heavy duty diesel engine. Engine output and emission characteristics were analyzed under variable air/fuel ratio and charging pressure. Since LPG is consisted of propane and butane, we investigated combustion characteristics using this two kinds of fuel. From the result of charging engine performance test, engine torque increase about 30% ∼ 40% with 0.3bar charging pressure. In low speed condition, as charging pressure increase, combustion stability improve ill lean bum condition, but, in high speed condition, combustion stability make worse in lean bum condition. We know that engine output decreased rapidly from the condition of air excess ratio 1.3. In addition, we measured emission characteristics under the lean bum and charging condition. From this experiment, we found that CO emission is out of the question in the range from stiochiometric to lean burn and charging condition, but charging pressure has influence on HC emission.