• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.339-342
• /
• 2010

Dual throat nozzle(DTN) is recently attracting much attention as a new concept of the thrust vectoring technique of propulsion jet. This DTN is designed with two throats, an upstream minimum and a downstream minimum at the nozzle exit, with a cavity in between the upstream throat and exit. In the present study, a computational work has been carried out to analyze the performance of a dual throat nozzle(DTN) at various mass flow rate of secondary flow. Two-dimensional, steady, compressible Navier-Stokes equations were solved using a fully implicit finite volume scheme. The present computational results were validated with some experimental data available. Based upon the present results, Thrust-vector control using a DTN is discussed in terms of the thrust coefficient and the coefficient of discharge.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.49 no.3
• /
• pp.13-18
• /
• 2012

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.5
• /
• pp.1044-1051
• /
• 1989

A numerical calculation is carried out for the analysis of 3-dimensional compressible flow field in axial-flow rotating blades by using finite element method. The calculation of flow in impellers plays a dominant role in the theoretical research and design of turbomachines. Three-dimensional flow fields can be obtained by the quasi-three-dimensional iterative calculation of the flows both on blade-to-blade stream surfaces and hub-to-shroud stream surfaces with the introduction of viscous loss model in order to consider a loss due to viscosity of fluid. In devising the loss model, four primary sources of losses were identified: (1) blade profile loss (2) end wall loss (3) secondary flow loss (4) tip-leakage loss. For the consideration of an axially parabolic distribution of loss, the results of present calcullation are well agreed with the results by experiment, thus the introduction of loss model is proved to be valid.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.2
• /
• pp.153-160
• /
• 2013

An orthotropic magneto-rheological rubber composite (MRRC) based on a general-purpose rubber can be manufactured by using an electromagnetic device during the curing processes of rubber mixtures. The magnetic transmissivity of MRRCs increases with the iron particle (IP) content, and that of aligned MRRCs with a 2-T magnetic field is 1.8 to 2 times higher as compared to that of randomly dispersed MRRCs. The effect of a 2-T magnetic field on carbon nanotube (CNT) reinforced MRRC has been identified clearly, and the magnetic transmissivity is found to be 3.7%. The compressive stress of MRRC (IP 90 + CNT 5, 2 T alignment) under a magnetic field of 0.49 T is 2.1 times higher as compared to that of the matrix. The MR effect of MRRC increases with the IP content, and that of aligned MRRC with the IP 90 and 2 T magnetic field is 20.4%. It is confirmed that the magnetic field when making the specimen and when performing the compression test greatly impacts the compression characteristics.

• Journal of computational fluids engineering
• /
• v.2 no.1
• /
• pp.37-45
• /
• 1997

벽면 근처에 가까이 위치하는 회전와류쌍을 음원으로 갖는 비정상 유동장에서 벽면이 음장에 미치는 효과를 알아보기 위해 이차원 음장 수치해석을 시도하였다. 비압축성 유동장에 대한 비정상 수력정보를 기반으로 오일러식에서 교란 압축성 소음항을 도출하였다. 원거리 자유 경계면은 비반사 경계조건을 이용하였으며, 벽면에서는 벽면 효과를 음향장에 고려하였다. 자유흐름장에 놓인 와류쌍이 대칭인 나선팔을 갖는 반면에, 벽면이 있는 경우엔 음파가 전달되는 경로를 따라 방향성이 존재함을 알 수 있었다. 본 연구를 통하여 벽면이 존재하는 경우에 비정상 수력정보를 이용하여 근거리와 원거리 음장을 동시에 수행할 수 있음을 알아내었다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.109-112
• /
• 2004

Of late, the thrust vectoring control, using fluidic co-flow and counter-flow concepts, has been received much attention since it not only improves the maneuverability of propulsive engine but also reduces an additional material load due to the trailing control wings, which in turn reduce the aerodynamic drag. However, the control effects are not understood well since the flow field involves very complicated non: physics such as shock wave/boundary layer interaction, separation and significant unsteadiness. Existing data are not enough to achieve the effectiveness and usefulness of the thrust vectoring control, and systematic work is required for the purpose of practical applications In the present study, computational study has been performed to investigate the effects of the thrust vector control using the fluidic co-and counter-flow concepts. The results obtained show that, for a given pressure ratio, the thrust deflection angle has a maximum value at a certain suction flow rate, which is at less than $5\%$ of the mass flow rate of the primary jet. With a longer collar, the same vector angle is achievable with smaller mass flow rate.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.7
• /
• pp.629-636
• /
• 2013

Pneumatic levitation is based upon Bernoulli's principle. However, this method is known to require a large gas flow rate that can lead to an increase in the cost of products. In this case, the gas flow rate should be increased, and the compressible effects of the gas may be of practical importance. In the present study, a computational fluid dynamics method has been used to obtain insights into Bernoulli levitation flows. Three-dimensional compressible Navier-Stokes equations in combination with the SST k-${\omega}$ turbulence model were solved using a fully implicit finite volume scheme. The gas flow rate, workpiece diameter,and clearance gap between the workpiece and the circular cylinder were varied to investigate the flow characteristics inside. It is known that there is an optimal clearance gap for the lifting force and that increasing the supply gas flow rate results in a larger lifting force.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.281-285
• /
• 2007

The flow characteristics in the thruster should be analyzed considering its geometry and the pressure ratio to estimate its performance and etc. This paper suggests the computational result of an axisymmetric real nozzle for the altitude control of a satellite to find out the application limit that the assumption of continuum mechanics holds. The steady non-reacted compressible flow field in the unstructured grid system is computed and analyzed with varying the environmental pressure (or the degree of vacuum) under the fixed pressure ratio in a real thruster of which the area ratio of exit to throat is 56. The assumption of the continuum mechanics is not approved when the environmental pressure is reduced less than $10^{-3}$ atm.

• Journal of the Society of Naval Architects of Korea
• /
• v.38 no.4
• /
• pp.1-10
• /
• 2001

A numerical solution method of the incompressible Reynolds-Averaged Navier-Stokes equations is applied for calculating turbulent flows and performances of a marine propeller in open-water, four-quadrant conditions. Computed propeller flows of the model propeller P4381, for which the experimental data of the open-water performances exist, reveal complex viscous-flow characteristics including three-dimensional flow separations in various off-design conditions and also computed propeller thrusts and torques agree quite well with experimental data except some cases for which severe propeller cavitations occurred in the experiment.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.249-252
• /
• 2011

고체로켓추진기관의 추력조절을 위해 핀틀 기술이 사용된다. 아직까지 핀틀 유동에 대해 근본적인 물리적 이해를 돕는 연구가 공개되지 않아, 이 연구에서 다양한 형상의 needle형 핀틀에 따른 유동구조에 대한 수치적 연구를 진행하였다. 2차원 축대칭, 압축성을 고려하여, 상용 열유체 해석 프로그램인 FLUENT 6.2를 사용하여 해석을 수행하였다. 난류 모델을 검증하기 위해 기 수행된 실험 결과와 비교하였다. 핀틀 각도(tip angle)가 작아질수록 노즐에서 유동 박리점이 하류로 이동하며, 핀틀에서 발생하는 끝단 충격파가 약해진다. 핀틀 반경(tip radius)이 작아질수록 핀틀에서 발생하는 끝단 충격파가 하류로 이동하며, 크기는 약해진다. 핀틀 형상(contour)은 유동 박리 지점에 직접적인 영향을 미친다.