• Korean Journal of Materials Research
• /
• v.34 no.4
• /
• pp.215-222
• /
• 2024

Because collagen is inherently piezoelectric, research is being actively conducted to utilize it to harvest energy. In this study, a collagen solution was prepared using edible low-molecular-weight peptide collagen powder, and collagen films were fabricated using a dip coating method. The collagen films prepared by dip coating showed a smooth surface without defects such as pinholes or cracks. Dehydrothermal treatment of the collagen films was performed to induce a stable molecular structure through cross-linking. The collagen film subjected to dehydrothermal treatment at 110 ℃ for 24 h showed a thickness reduction rate of 19 %. Analysis of the collagen films showed that the crystallinity of the collagen film improved by about 7.9 % after dehydrothermal treatment. A collagen film-based piezoelectric nanogenerator showed output characteristics of approximately 13.7 V and 1.4 ㎂ in a pressure test of 120 N. The generator showed a maximum power density of about 2.91 mW/m² and an output voltage of about 8~19 V during various human body movements such as finger tapping. The collagen film-based piezoelectric generator showed improved output performance with improved crystallinity and piezoelectricity after dehydrothermal treatment.

• Clean Technology
• /
• v.23 no.1
• /
• pp.90-94
• /
• 2017

These days much efforts are being dedicated to wind power as a potential source of renewable energy. To maintain effective and uniform generation of energy, defect preservation of turbine blade is essential because it directly takes effects on the efficiency of power generation. For the effective maintenance, early measurements of blade defects are very important. However, current technologies such as ultrasonic waves and thermal imaging inspection methods are not suitable because of long inspection time and non-real time inspection. To supplement the problems, the study introduced a method for real time defect monitoring of a blade surface based on surface wave technology. We examined the effect of various parameters such as micro-cracks and peelings on the propagation of surface wave.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.219-219
• /
• 2008

Energy harvesting from the environment has been of great interest as a standalone power source of wireless sensor nodes for ubiquitous sensor networks (USN). There are several power generating methods such as thermal gradients, solar cell, energy produced by human action, mechanical vibration energy, and so on. Most of all, mechanical vibration is easily accessible and has no limitation of weather and environment of outdoor or indoor. In particular, the piezoelectric energy harvesting from ambient vibration sources has attracted attention because it has a relative high power density comparing with other energy scavenging methods. Through recent advances in low power consumption RF transmitters and sensors, it is possible to adopt a micro-power energy harvesting system realized by MEMS technology for the system-on-chip. However, the MEMS energy harvesting system hassome drawbacks such as a high natural frequency over 300 Hz and a small power generation due to a small dimension. To overcome these limitations, we devised a novel power generator with a spiral spring structure. In this case, the energy harvester has a lower natural frequency under 200 Hz than a normal cantilever structure. Moreover, it has higher an energy conversion efficient because shear mode ($d_{15}$) is much larger than 33 mode ($d_{33}$) and the energy conversion efficiency is proportional to the piezoelectric constant (d). We expect the spiral type MEMS power generator would be a good candidate as a standalone power generator for USN.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.8
• /
• pp.635-639
• /
• 2013

Generating output characteristics of a EYE-type piezoelectric generator depending on ceramic size and materials of the elastic body were studied. EYE-type piezoelectric-generating device consist of the ceramic was attached between the both elastic body. piezoelectric-generating is that if the tension occurred at both ends of an elastic body, the piezoelectric effect occurs at ceramics through the form change of the elastic body. The structure of this EYE-type generator use various area. than a existing type generator, because the ceramic position of the directly force at does not apply. Resonance and output characteristics of the generator were analyzed by using FEM program. Generators were fabricated on the basis of analyzed results and attached on a frequency controllable vibrator to measure output characteristics. Also, the experimental results were compared with the simulated results. As a result, output characteristics of the generator increased depending on the increase in ceramic thickness. In case of increase in ceramic width, resonance frequency of the generator also decreased.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.7
• /
• pp.462-468
• /
• 2018

The piezoelectric energy harvesting characteristics of a trapezoidal cantilever generator with lead zirconate titanate (PZT) laminate were investigated with various Ag inner electrodes. The piezoelectric mode of operation was a transverse mode by using a planar electrode pattern. The piezoelectric cantilever generator was fabricated using trapezoidal cofired-PZT/Ag laminates by five specimens of 2, 3, 4, 7, and 13 layers of Ag. As the number of Ag electrodes increased, impedance and output voltage at resonant frequency significantly decreased, and capacitance and output current showed an increasing tendency. A maximum output power density of $7.60mW/cm^3$ was realized for the specimen with seven Ag layers in the optimal condition of acceleration (1.2 g) and resistive load ($600{\Omega}$), which corresponds to a normalized power factor of $5.28mW/g^2{\cdot}cm^3$.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.80-80
• /
• 2011

세계 기후 변화와 불안정한 유가 변화에 대응하고 국내산업의 저탄소 녹색성장을 위해 신재생에너지 개발이 활발하게 이루어지고 있다. 해양에너지 중에서 조류발전은 대규모 댐을 건설할 필요가 없어 비용이 적게 소요되고 특히 날씨 변화나 계절에 관계가 없고, 발전량이 예측 가능하므로 신뢰성 있는 에너지원으로 적용이 가능하다. 조류발전기 블레이드에 폴리머계 복합재료와 스테인리스강이 대부분인데, 이 재료는 특정 회사에서만 제작 가능하며, 충격에 약하고, 균열전파 속도가 빠르며, 대단히 고가이며, 수입에 의존하고 있는 실정이다. 이러한 조류발전에 사용되는 블레이드는 가혹한 부식, 캐비테이션 그리고 침식환경에 노출되어 있어 내구성이 우수한 제품개발이 대단히 중요하며, 조류발전 블레이드를 동합금으로 제작시, 내식성이 뛰어나며 구리의 특성상 해양생물 서식을 방지할 수 있고, 내캐비테이션 특성, 내구성, 가공성 및 유지보수가 용이한 장점이 있다. 이러한 동합금에 WC-27NiCr와 WC-10Co4Cr를 초고속 화염용사(HVOF)를 이용하여 코팅층의 캐비테이션 특성 및 전기화학적 거동을 연구하였다. 본 연구에서는 조류발전용 블레이드의 재료로 사용하려는 동합금에 WC-27NiCr와 WC-10Co4Cr이 용사코팅된 시험편을 사용하였다. 다채널 부식시험기인 WonA-tech WMPG-1000을 이용하여, 자연전위를 측정하였으며, 분극실험은 자체 제작한 홀더를 사용하여 $0.3318cm^2$를 노출 시켜 실험하였다. 기준전극은 은/염화은 전극을, 대극은 백금 전극을 사용하였다. 양분극과 음분극 실험을 통해 개로전위에서의 부식거동을 확인하였고, 정전위 실험도 실시하였다. 실험 종료 후 3D현미경 및 전자주사현미경(SEM)을 사용하여 코팅층 표면의 손상거동을 관찰하였다. 캐비테이션 실험은 ASTM-G32 규정에 의거하여 압전효과를 용한 진동발생 장치(RB 111-CE)를 사용하였다. 수조는 전기화학적 부식의 영향을 고려하여 아크릴로 제작하였고, 시험편은 실험장비에 맞게 파인커팅머신을 이용하여 $20mm{\times}20mm$로 절단하여 사용하였으며 혼과 대향하도록 하여 1mm 간격을 두어 실험하였다. 실험 실시 전, 미소전자저울을 사용하여 무게감소량을 측정하였으며 표면관찰을 통하여 캐비테이션 거동을 관찰하였다.

• Korean Journal of Materials Research
• /
• v.34 no.1
• /
• pp.34-43
• /
• 2024

New piezoelectric and triboelectric materials for energy harvesting are being widely researched to reduce their processing cost and complexity and to improve their energy conversion efficiency. In this study, BaTiO₃ films of various thickness were deposited on Ni foams by R.F. magnetron sputtering to study the piezoelectric and triboelectric properties of the porous spongy structure materials. Then piezoelectric nanogenerators (PENGs) were prepared with spongy structured BaTiO₃ and PDMS composite. The output performance exhibited a positive dependence on the thickness of the BaTiO₃ film, pushing load, and poling. The PENG output voltage and current were 4.4 V and 0.453 ㎂ at an applied stress of 120 N when poled with a 300 kV/cm electric field. The electrical properties of the fabricated PENG were stable even after 5,000 cycles of durability testing. The triboelectric nanogenerators (TENGs) were fabricated using spongy structured BaTiO₃ and various polymer films as dielectrics and operated in a vertical contact separation mode. The maximum peak to peak voltage and current of the composite film-based triboelectric nanogenerator were 63.2 V and 6 ㎂, respectively. This study offers new insights into the design and fabrication of high output nanogenerators using spongy structured materials.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.12
• /
• pp.955-960
• /
• 2012

We fabricated piezoelectric unimorph cantilever generators (UCG) using $Pb(Zr_{0.54}Ti_{0.46})O_3$ + 0.2 wt% $Cr_2O_3$ + 1.0 wt% $Nb_2O_5$ (PZCN) piezoelectric thick films, which were produced by a tape casting method. The PZCN thick films were tailored with same width and thickness but different lengths from 7.7 to 57.7 mm in order to evaluate optimized UCG for energy harvesting device applications. When the length of PZCN film was increased, the resonance frequency of UCG was slightly increased from 7 Hz to 8 Hz, which could be due to enlarged area of the highly stiff piezo-ceramic film. However, the output power was proportionally increased with the length of PZCT film and it reached 4.68 mW (1.221 $mW/cm^3$) when the film's length was 57.7 mm under 25 g of tip mass at 8 Hz, which is sufficient for micro-scale device applications.