• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.2
• /
• pp.303-309
• /
• 2010

Copper tube rolling process using the planetary rolling mill has been studied by using finite element method. This rolling is process that makes copper tube by three-roll with mannesmann method. Also, rolling process has started from the cold working and finished to the hot working. This rolling process has more advantage that make reduction of process and cost than existing extrusion. This process includes various and complex process parameters. Each of the process parameters affects forming result. Therefore, all of the process parameters should be considered in copper tube rolling. Rolling process for copper tube was successfully simulated and it should be useful to determine optimal rolling condition.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.2
• /
• pp.244-251
• /
• 2011

Pipe rolling process using the planetary rolling mill for AISI 304 stainless steel has been studied by using finite element method. Mannesmann method using three-roll is applied to this rolling process. Commonly, rolling process has started from the cold working and finished to the hot working. This rolling process has more advantage that make reduction of process and cost than existing extrusion process. This process includes various and complex process parameters. Each of the process parameters affects forming result. Therefore, all of the process parameters should be considered in FEA. In this study, possibility and productivity of forming pipe for AISI 304 stainless steel had been investigated. Also, preheating process and variations of rotation velocity and product thickness were considered in FEA. Rolling process for AISI 304 stainless steel pipe was successfully simulated and it should be useful to determine optimal rolling condition.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.1
• /
• pp.63-68
• /
• 2017

This paper reviews the learning model of a forward slip ratio in order to improve the mass-flow stability and strip qualities in the hot strip finishing mill process. Firstly, it is shown, from mathematical analysis, that the significant parameters of the forward slip ratio are the tension, looper angle, and roll velocity. Secondly, a discrete-time learning model of the forward slip ratio is proposed from these parameters, which is identified by an instrumental variable (IV) identification algorithm. Finally, it is shown from computer simulation that the proposed learning model is more effective than the existing learning model.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2001.05a
• /
• pp.157-160
• /
• 2001

회전체 베이링 상태진단에 신뢰성을 갖기 위하여 여러 가지 진단 방법이 연구되고 있으며, 이때 이용하는 변수는 온도와 소음, 진동 그리고 윤활유가 있으며 분석 방법으로는 온도추이분석, 소음분석, 진동분석, 윤활제 분석방법이 주로 이용되고 있다. 본 연구에서는 압연기 베어링의 상태진단의 변수로 베어링의 진동 신호를 선택하고 이 진동신호에서 비선형성이 강한 신호 즉 카오스적 거동이 있음을 타켄스의 매립법과 포엔카레 단면을 이용하여 확인하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1155-1165
• /
• 1990

A new method of predicting effect of rolling parameters on roll pressure, roll force, and power and energy consumptions in hot strip rolling is presented. The method is based on approximate solutions for velocity, strain rate, and stress distributions in the roll gap. The degree of approximation was examined by the finite element solutions. The theoretical predictions were compared with experimental data from hot rolling of steel strip and steel plate.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.11
• /
• pp.1437-1443
• /
• 2011

Thick plates produced by the rolling process are used as the basic elements of ship structures. In this paper, we present a setup model for controlling the asymmetric factors causing plate bending in the width direction during plate rolling. A series of three-dimensional finite element analyses is conducted to predict the relationship between various asymmetric factors and plate bending. The setup model is developed by performing regression on the relationship to produce linear equations with several nondimensional parameters. The setup model is verified with a pilot rolling test in which variations in thickness and temperature differences in the width direction exist. The results show that the bending curvatures predicted by the model are in fairly good agreement with the measured results for those asymmetric factors.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.29-34
• /
• 2017

In this paper, we report a method of improving the productivity of lead wire fabricated through the rolling process by increasing its linear velocity. The most important point to consider when raising the linear velocity is that the original specifications must still be adhered to. In other words, the dimensional tolerance must be satisfied when increasing the linear velocity of the wire without causing cracks. However, if the linear velocity of the wire is increased, the degree of reduction must also be increased, which causes more damage to the wire and increases the load on its surface. Therefore, we studied a three step rolling process which can satisfy the specifications of the wire produced through the two step rolling process and improve the productivity. In this study, only the roll gap of the three-stage rolling roller is assumed to be a variable, while the other conditions are the same as the field conditions. In addition, through the PIANO (Process Integration, Design and Optimization) tool, the (optimum?) surface roughness and maximum stress are maintained.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.10
• /
• pp.1255-1260
• /
• 2012

The densification behavior of titanium powder in the direct powder rolling process was investigated. An analytical model for the roll-backlash phenomenon during this process was proposed to conduct a realistic finite element analysis. Furthermore, the roll-backlash was quantitatively analyzed, and the relative densities of the greenstrip along the rolling direction were precisely estimated. Finally, the slip and nip phenomena were identified by calculating the contact pressure and shear stress between the titanium powder and the roller in order to understand the densification behavior of the powder during the rolling process.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.26-26
• /
• 2003

본 연구에서는 누적압연접합공정(ARB)을 통하여 5052 알루미늄 합금의 결정립을 약 0.2$\mu\textrm{m}$ 크기로 미세화 하였다. 누적압연에 의한 변형량 증가에 따른 미세 조직 변화와 결정립 간의 상대적인 방위각 차이를 TEM을 이용하여 관찰하였다. 누적 변형량을 함수로 상온 인장특성을 분석하였고, 초미세립 소재를 후속 열처리한 후 미세 조직 변화를 관찰하여 제조된 초미세립 소재의 열적 안정성을 평가하였다. 상온 대기 중에서 pin-on-disk 형태의 마멸시험기를 사용하여 초미세립 소재의 미끄럼 마멸시험을 변형량과 하중을 변수로 행하였다. 강소성 변형에 의해 제조된 5052 알루미늄 합금 소재의 마멸저항성은 강소성 변형 전과 비교하여 소재의 경도가 크게 증가하였음에도 불구하고 오히려 감소하였다. 마멸시험 후 마멸면의 SEM, 마멸단면의 OM 관찰과 마멸면 직하의 깊이에 따른 경도측정을 통하여 초미세립 소재의 마멸기구를 분석하였고 마멸표면의 변형 층을 관찰하였다. 또한 마멸면 직하 조직의 TEM 관찰을 통해서 마멸시험 중의 미세 조직 변화를 연구하였다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.84-86
• /
• 2007

Aluminum sheets were asymmetrically cold rolled without lubrication by using different roll velocities of upper and lower rolls in order to intensify the shear deformation. During asymmetrical cold rolling of aluminum sheets, a reduction per a rolling pass, initial sheet thickness, roll diameter, roll velocity ratio were varied to investigate the effect of rolling parameters. The formation of through thickness shear texture was related to the ratio of the contact length between the roll and sample($l_c$) to the sheet thickness(d). The strain states associated with asymmetrical rolling were investigated by the finite element method (FEM) simulation. FEM results indicated that the evolution of deformation texture in a thickness layer is strongly governed by integrated values of strain rates $\dot{\varepsilon}_{13}$ and $\dot{\varepsilon}_{11}$ along the streamline in the roll gap.