• Journal of Welding and Joining
• /
• v.5 no.1
• /
• pp.23-33
• /
• 1987

Plasma arc cutting is a fusion cutting process in which a gas constricted arc is employed to produce high temperature, high velocity jet at the workpiece. Even though the plasma arc cutting has been wid¬ely used in the industry, very little work has been done on the analysis of the process. In this paper, the kerf width was numerically analyzed by soving the temperature distribution in base metal under consideration of the latent heat effect. In modelling the heat flow problem, the heat intensity of the plasma arc was assumed to have a Gaussion distribution in the transverse direction and expone¬ntially decreasing in the thickness direction. The thermal efficiency and the heat input ratio of the top surface were experimentally deterimned for various thickness and cutting conditions, and used in numerical calculation of the kerf width. The experimental results were in eonsiderabely good agreement with the theoretically predicted kerf width.

• Journal of Welding and Joining
• /
• v.10 no.4
• /
• pp.222-229
• /
• 1992

A prediction of penetration and heat affected zone by using Finite Element Method in CO$_{2}$ Arc Welding has been discussed this paper. The temperature distribution of a base metal produced by the CO$_{2}$ arc welding processing is analyzed by using a three dimensional finite element model. The common finite element program ANSYS 4.4A was employed to obtain the numerical results. Temperature dependent material properties, effect of latent heat, and the convective boundary conditions are included in the model. Numerically predicted sizes of the penetration and the heat affected zone are compared with the experimentally observed values. As a result, there was a slight difference between numerical analysis values and experimentally observed values. For in the case of heat affected zone, it was not considered a precise forced convective coefficient value, and in the case of penetration, it was not, considered a arc force.

• 전기의세계
• /
• v.24 no.6
• /
• pp.39-44
• /
• 1975

발광반도체로 사용하는 재료는 주로 화합물반도체로 최근 주입형 발광 다이오드가 미소 전력으로 동작하고 수명이 길명 신뢰성이 높다는 장점때문에 실용화가 급진전되었다. 이중 GaAs를 사용한 적외발광 다이오드는 비교적 일찍 부터 개발되어 각종 발광소자와 조합하여 이용되었고 더욱 기술의 개발로 GaP, GaAl$_{1-x}$ Asx GaAsrxPx를 사용한 적외발광 다이오드를 중심으로 표시광원이나 수자, 문자 표시 소자로서 이미 양산화 단계를 이루어 다방면에 실용화가 이룩되고 있다. 또 최근 보다 많은 정보를 표시하기 위하여 적색 이외 가시다이오드의 개발이 요망되고 Gap, SiC, NaN등의 녹색발의 실현이 주목되고 있다. 이와같이 전기 에너지가 광에너지로 변환되는 것은 첫째 물질을 고온으로 가열할 때 그 물질에서 발생하는 열복사로서 전구 SiC에서 나오는 광이 이에 속하고 둘째로 아아크 방전, 그로우 방전을 이용한 영사기의 광원을 들 수 있고 셋째 루미네선스로 음극 루미네선스와 광루미네선스 및 EL 루미네선스 등이 있다. EL. 루미네선스도 전기에너지를 광에너지로 직접변환 하므로 변환효율이 높은 것이 특징으로 여기서는 EL 루미네선스에 관해 논하기로 한다.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.385-388
• /
• 1994

This paper presents a new configure rectifier which has improved input power factor and efficiency for DC arc weldings. Two rectifiers are series connected and they are single-phase full-wave phase controlled rectifiers that use a transformer with two center-tapped secondary. The input power factor can be improved by controlling the each phase of rectifiers sequentially, and then the efficiency can be also improved because the reactive component currents will be reduced. It is confirmed that the proposed rectifiers has about 80% of input power factor and efficiency with the experimental results which are carried out at the output ranges of 100A to 300A.