• Journal of the Earthquake Engineering Society of Korea
• /
• v.10 no.6 s.52
• /
• pp.103-114
• /
• 2006

Forced vibration testing is important for correlating the mathematical model of a structure with the real one and for evaluating the performance of the real structure. There exist various techniques available for evaluating the seismic performance using dynamic and static measurements. In this paper, full scale forced vibration tests simulating earthquake response are implemented by using a hybrid mass damper. The finite element (FE) model of the structure was analytically constructed using ANSYS and the model was updated using the results experimentally measured by the forced vibration test. Pseudo-earthquake excitation tests showed that HMD induced floor responses coincided with the earthquake induced ones which were numerically calculated based on the updated FE model.

• Magazine of the Korea Concrete Institute
• /
• v.8 no.2
• /
• pp.139-150
• /
• 1996

The objective of this study is to provide the information on the manufacturing and exper- , ructures. imental techniques of small scale modeling of precast concrete(P.C.) large panel :-t The ad~~pted scale was one-fifth. 4 types of experiments were performed : nlaterial tests for model concrete and model reinforcement, compressive test of horizontal joint, shear test of vertical joint and cyclic static test of 2-story subassemblage structure. Based on the experimental results, the following conclusions are drawn : i 1) Model concrete had in general larger compressive strength than expected. (2) Model reinforcement showed less ductility if the annealing processes were performed without using vaccuum tube. 131 Failure niotles of horizontal and vertical joints were almost same for both prototype and model. But the strength of model appears to be higher than required by similitude law. (41 Hysteretic behavior of 1 /T, scale subassemblage model can be made quite similar to that of prototype if the ductility of model reinforcement and compressive strength of model concrete could be representative of those of prototype.

• Fire Science and Engineering
• /
• v.13 no.4
• /
• pp.30-37
• /
• 1999

In this study, reduced-scale experiments as the alternative to a real-scale fire test were conducted to understand fire properties in atrium space. The scaling laws were derived from $\pi$-parameters which were deduced by dimensional analysis of governing equations (continuity, conservation of momentum and conservation energy). The 1/50 scale experiment simulated the real-scale fire test in SIVANS atrium at Japan were conducted under the scaling laws. And this results were compared with real-scale experiment results. Furthermore these results were visualized by video recording system using laser light sheet.

• Fire Science and Engineering
• /
• v.25 no.3
• /
• pp.51-56
• /
• 2011

The full-scale experiments are carried out to investigate the fire suppression characteristics of water-based fire fighting systems in a road tunnel. Applied systems are the low-pressure water spray system at 3.5 bar and the high-pressure water mist system at 60 bar. The water flow rate of the high-pressure system is one sixth only of the water spray system. A passenger car and a heptane fuel pan with area of $1.4m^2$ are used as fire sources. A blower system is installed at the tunnel exit to realize the longitudinal ventilation conditions (0.9~3.8 m/s) in the tunnel. Temperatures from the fire source to the down-stream direction are measured by K-type thermocouple trees. The experimental results show that the cooling effect of the high pressure water mist system in the test conditions were equivalent to that of the low pressure water spray system for B-class fire.

• Tunnel and Underground Space
• /
• v.28 no.1
• /
• pp.97-110
• /
• 2018

The application of sprayed waterproofing membrane with high adhesion and ductility is considered to be promising as a measure for repair and reinforcement of a tunnel structure. Therefore, a powder-type and one-component membrane prototype with high tensile and bond strengths was made in this study. Then, its reinforcement effect on a shield segment was evaluated by carrying out a series of full-scale loading tests of segment specimens on which the membrane was sprayed. From the tests, it was confirmed that the initial cracking loads increased by approximately 34% due to cracking retardation by membrane coating. Even though the increase of failure loads were not so high as cracking loads, the strain-softening behaviors were observed from specimens coated by the membrane. Therefore, it is expected that the membrane coated on the inner surface of a lining might be effective in preventing its brittle failure.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.6
• /
• pp.148-156
• /
• 2018

The integrity assessment of the bridge behavior is generalized by field data of a static load-deformation curve and dynamic properties such as impact factors and natural frequencies. Evaluating it with numerical analysis is a reasonable method. The results of the mockup test and the numerical analysis are corresponded with each other since the behavior of service load proceeds in elastic region. In case of the dynamic behavior of structure, especially for the analysis of vibration, the result of the mockup test differs from the result of numerical analysis a little due to the geometric shape and non-homogeneous materials. In order to converge on these tolerances, this study suggested several numerical models, analyzed the sensitivity and finally offered a practical modeling method for the estimation of bridge on the basis of the result of mockup test. Based on the model substituted concrete section for strands section, the natural frequency of the model composed with axial stiffness of strands or the model applied the modified modulus of elasticity was closest with the result of the mockup test.

• Magazine of the Korea Concrete Institute
• /
• v.8 no.3
• /
• pp.177-185
• /
• 1996

Four types of experiments were performed to check the similitude of member behavior between prototype and 1 /10 scale models : (1) Test of slender columns with P-$\Delta$ effect, (2) Test of short columns with and without confinement steel, (3) Test of simple beams without stirrups, and (4) 'T-beam test. Based on the results of experiments, the conclusions were made as follows : (1) The P-$\Delta$ effect of slender columns can be almost exactly represented by 1/10 scale model. (2) The effect of confinement on short columns by the hoop steel can be also roughly simulated by 1/10 scale model. (3) The failure modes of simple beams without stirrups are brittle shear failures in prototype whereas those of 1/10 scale models are the ductile yielding of tension steel followed by large diagonal tension cracking and compressive concrete failure. (4) The behaviors of prototype and 1/10 scale model in T-beams appear very similar.

• Proceedings of the Korean Information Science Society Conference
• /
• 1998.10a
• /
• pp.33-35
• /
• 1998

본 논문에서는 형식론적 모델링 및 모의 실험 방법을 사용하여 병렬 디스크의 성능 예측 및 영상 데이터용 비선형 편집기의 개발을 위한 여러 형태의구조에 대해서 모의 실험한 결과 및 성능에 영향을 미치는 요소들에 대해 다루고 있다. 컴퓨터가 발전하기 전에는 테이프를 이용한 선형 편집기를 사용하였으나. 컴퓨터가 발전하고 또한 입출력 장치의 성능이 향상되면서 RAID(Redundant Array of Inexpensive Disk)가 개발되었고, 이것을 이용한 비선형 편집기가 개발되었다. 병렬디스크는 비선형 편집기뿐만 아니라 VOD(Video On Demand)나 데이터 서버등 응용분야가 많고, 요구되는 성능에 따라서 다양한 구조의 병렬디스크가 사용된다. 매우 큰 대역폭이 요구되는 병렬디스크의 경우에는 다양한 버스와 버퍼를 사용한 복잡한 계층적 구조가 요구된다. 그러나 이렇게 복잡한 병렬디스크를 개발하기 에 적당한 개발 도구가 없어 필요한 성능에 꼭 맞는 시스템을 개발하기가 어렵다. 특히 디스크의 성능을 수학저으로 쉽게 구할 수 없다. 또한 시스템이 실물로 완성되기 전에는 디스크의 운영 알고리즘의 개발 및 파일 시스템의 개발이 쉽지 않다. 그래서 쉬운 소프트웨어 개발과 디스크의 성능을 쉽게 측정하기 위해서 객체 지향 성능 예측시스템(OOPPS :Objet Oriented Performance Prediction System)을 개발하였고, 이것을 이용하여 HDTV용 비선형 편집기의성능을 예측하고, 필요한 성능을 만족하는 구조를 선택하여 실물로 개발하였다.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2009.04a
• /
• pp.415-422
• /
• 2009

국내 저층 공동주택 화재시의 화재 전파 경로와 상층으로의 화재 전파를 살펴보기 위하여 4층 공동 주택을 대상으로 실물화재 실험을 수행하였다. 화재는 3층 주택에서 발화하는 것으로 하였고, 초기 화원은 주방에서 과열된 식용유에 발화되어 발생하는 것으로 하였다. 주택 내부 가연물은 일반 가정의 필수 가연물을 모두 포함 하였다. 내부 화재 성상을 확인하기 위하여 가시화, 주요부의 온도측정, 산소농도 측정을 수행하였다. 실험 결과 초기 화원의 발화 시간, 화재 층 내부 각 구획으로의 전파시간, 전역화재 발생시간을 파악하였으며, 상층으로의 연소확대 경로를 파악하였다.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2013.04a
• /
• pp.103-104
• /
• 2013

본 연구에서는 침대 매트리스에 대해서, 실물규모 화재시험을 이용한 열방출율(Heat release rate: 이하 HRR)을 측정할 때의 불확도(Uncertainty) 산정을 위한 정보제공을 목적으로 함. 실제 실험데이터를 바탕으로 불확도에 영향 미치는 개별요인들을 도출한 개별 요인들의 합성을 통해 불확도를 산정하였음.