• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.1
• /
• pp.15-21
• /
• 2011

In this study, flexural strength and fracture behavior of silicon die from single crystalline silicon wafer were investigated as a function of thickness. Silicon wafers with various thickness of 300, 200, 180, 160, 150, and 100 ${\mu}m$ were prepared by mechanical grinding and polishing of as-saw wafers. Flexural strength of 40 silicon dies (size: 62.5 mm${\times}$4 mm) from each wafer was measured by four point bending test, respectively. For statistical analysis of flexural strength, shape factor(i.e., Weibull modulus) and scale factor were determined from Weibull plot. Flexural strength reflecting both statistical fracture probability and size (thickness) effect of brittle silicon die was obtained as a linear function of die thickness. Fracture appearance was discussed in relation with measured fracture strength.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.9
• /
• pp.1175-1182
• /
• 2013

The lock-in mode infrared thermography (IRT) technique has been developed to improve the detection capability of defects in materials with high thermal conductivity, and it has been shown to provide better detection capability than conventional active IRT. Therefore, to investigate the application of this technique to nuclear piping components, lock-in mode IRT tests were conducted on pipe specimens containing simulated wall-thinning defects. Phase images of the wall-thinning defects were obtained from the tests, and they were compared with thermal images obtained from conventional active IRT tests. It showed that the ability to size the detected wall-thinning defects in piping components was improved by using lock-in mode IRT. The improvement was especially apparent when detecting short and narrow defects and defects with slanted edges. However, the detection capability for shallow wall-thinning defects did not improve much when using lock-in mode IRT.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.125-125
• /
• 2017

최근 들어 내수용 및 수출용 자동차 보증 제도를 살펴보면 부품에 대한 방식 보증기간이 점차 연장되는 추세이며, 이에 따라 자동차사에서 요구하는 방식 및 내식성 평가 기준이 상향되어 가고 있다. 실제로 수출차에 대한 방청 품질 보증기간이 차체 구멍 발청 10년에서 12년으로 연장할 움직임을 보이는 등 점차 방식에 대한 관심이 높아지고 있다. 따라서 내식성 향상에 대한 끊임없는 연구가 지속적으로 이루어지고 있으며, 내식성 향상을 위해 구조/형상 변화, 도장 품질 향상, 최적화 설계 등 다방면에서 노력을 기울이고 있다. 그 중에서도 가장 근본적인 해결책인 소재의 내식성 향상에 대한 관심은 날로 높아지고 있는 실정이다. 특히 일본 등지에서는 GA 도금재의 사용이 증가하고 있으나, 아직은 내식성에 대한 효율적이고 체계적인 관리가 부족한 면이 있다. GA재는 합금화 과정에서 야기되는 Fe% 합금화도, 합금화 상분율(감마, 델타, 제타상), crater 등 복잡한 소재의 특성으로 인해 소재의 내식성 분석에 고려할 사항이 많다. 실제 여러 실험들을 통해서 GA재가 내식성에 영향이 있는 인자들에 대해 많은 연구가 진행되었지만 명확히 정량화되어 있지 않은 관계로 GA재의 내식성 관리 기준에 대해서도 명확하진 않은 상황이다. 본 연구에서는 당사재와 타사재의 고강도 GA재 (>440 MPa) 11종에 대해 crater분율, zeta상, 합금화도, 도금량 등의 다양한 도금 물성들을 조사하였다. 또한 이 시편들을 34일 동안의 복합염수 분무법(CCT)을 통해 얻은 최대 및 평균 블리스터 폭과 소재 표면품질 물성과의 상관관계를 통해서 부식과 연관된 관련인자들을 도출하고 정량적인 관계를 살펴보았다. GA재의 경우 다양한 물성들 중에서 도금 크레이터, 제타상, 합금화도 순으로 내식성에 영향을 주는 것으로 확인이 되었으며 이 세 인자들을 내식성 평가 지수화하여 GA재 생산시 효율적인 관리범위를 지정하는데 이용 가능할 수 있도록 diagram을 도출하였다. 따라서, 본 연구를 통하여 자동차사에서 요구하는 내식성 기준을 만족하기 위한 내식성 상관 인자들의 관리 수준을 정량화함으로써 보다 우수한 소재의 관리를 할 수 있도록 하고자 한다.

• Journal of Powder Materials
• /
• v.24 no.6
• /
• pp.450-456
• /
• 2017

Reaction-bonded silicon carbide (RBSC) is a SiC-based composite ceramic fabricated by the infiltration of molten silicon into a skeleton of SiC particles and carbon, in order to manufacture a ceramic body with full density. RBSC has been widely used and studied for many years in the SiC field, because of its relatively low processing temperature for fabrication, easy use in forming components with a near-net shape, and high density, compared with other sintering methods for SiC. A radiant tube is one of the most commonly employed ceramics components when using RBSC materials in industrial fields. In this study, the mechanical strengths of commercial RBSC tubes with different sizes are evaluated using 3-point flexural and C-ring tests. The size scaling law is applied to the obtained mechanical strength values for specimens with different sizes. The discrepancy between the flexural and C-ring strengths is also discussed.

• Composites Research
• /
• v.14 no.2
• /
• pp.8-12
• /
• 2001

Filament Winding Process is a comparatively simple operation in which continuous reinforcements in the form of roving are wound over a rotating mandrel. It is well established and versatile method for storage tanks and pipes for the chemical and other industries. In this study, tensile strength of a filament wound ring specimens were evaluated by a split disk test fixture and a dress disk test fixture. The results obtained from experiments were compared with the theoretical values from the rule of mixtures. The purpose of this paper is the suggestion of an appropriate test method for the evaluation of tensile properties of filament wound structures. The tensile strength of a ring specimen tested by the dress disk test showed better agreement with the theoretical values than those tested by the split disk test because of higher stress concentration in edges of a split disk test fixture. The results showed that the tensile strength of a ring specimen was influenced by the geometry of test fixture, the continuity of fibers, fiber-tension, fiber-end and stress concentration in specimen.

• Composites Research
• /
• v.14 no.2
• /
• pp.22-32
• /
• 2001

Damage induced by low-velocity impact on the curved composite laminates was experimentally evaluated for CFRP cylindrical shells with the radius of curvatures of 50, 150, 300, and 500 mm. The result was then compared with that of flat laminates and with the results by nonlinear finite-element analysis. The radius of curvatures and the effective shell stiffness appeared to considerably affect the dynamic impact response of curved shells. Under the same impact energy level, the maximum contact force increased with the decreasing radius of curvatures, with reaching 1.5 times that for plates at the radius of curvature of 50 mm. Since the maximum contact farce is directly related to the impact damage, curved laminates can be more susceptible to delamination and less resistant to the low-velocity impact damage. Delamination was distributed rather evenly at each interface along the thickness direction of curved laminates on the contrary to the case of flat laminates, where delamination is typically concentrated at the interfaces away from the impact point. This implies that the effect of curvatures has to be considered for the design of a curved composite laminate.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.1
• /
• pp.7-13
• /
• 2013

The surface microcrack over a few tens of micrometers is one of severe problems of a steel wire rod to lead to the failure of the final products, so the method to evaluate crack depth has been required to develop. This work investigates the feasibility of electromagnetic acoustic resonance (EMAR) for this problem. EMAR is the method for measurement of resonant features using electromagnetic acoustic transducer (EMAT). Generally, EMAR is sensitive to small variation of the structures and easy to apply it to the industrial field because of the feature of noncontact measurement. Through several EMAR experiments, the change of the resonant frequencies and attenuation in reverberation has been observed. The results confirms that the surface cracks of around 100 micrometer depth can be detected successfully with the present method.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.169-172
• /
• 2008

Carbon fiber reinforced polymer (CFRP) laminates can be used more efficiently in strengthening applications by applying prestress to the CFRP laminates. A key problem for prestressing with CFRP laminates is anchoring the laminates. These may include fracture to the CFRP laminates due to excessive gripping force or slippage of the CFRP laminates out of the anchorage zone caused by low friction between the anchor device and the lamiantes. The main objective of this study is the development of an applicative mold-type anchorage system for prestressed CFRP laminates through experimental study. The experimental parameters were the type of anchorage detail and the effect of surface treatment. The test results showed that the developed anchor assures 100% CFRP laminate strength.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.8
• /
• pp.1519-1529
• /
• 1992

A stepped specimen which is subjected to step loading is modeled to study the initiation and growth of adiabatic shear band using explicit time integration finite element code. The material model for specimen includes effects of thermal softening, strain hardening and strain rate hardening. Various mesh sizes are tested to check whether they are small enough to model highly localized discontinuous phenomena reasonably well. It is shown that the number of adiabatic shear band depends on impact velocity and it is also shown that the initiation and growth of adiabatic shear band inversely depends on prescribed velocity at the top of specimen.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1998.05a
• /
• pp.95-95
• /
• 1998

현장에서 부식속도를 측정하는 방법의 하나인 전기저항 프로브(Electric Resistance Probe, ER probe)는 시편이 부식되는 양에 비례하여 저항이 증가하는 원리를 이용한 것으로 부식기구에 무관하게 직접적인 부식속도의 측정이 가능하다. 그러나, 와이어나 판형으로 기계 가공된 프로브로 제작되어 미량의 부식에는 저항변화폭이 작아 긴 측 정시간이 필요하고, 특히 국부 부식의 경우 부식이 상당히 진행되더라도 전체 저항변 화가 크지 않은 문제점이 있다. 박막형 전기저항프로브는 미량의 부식에서도 저항변화폭이 크게 나타나도록하기 위 하여 금속 박막을 스퍼터링으로 증착하여 동일 부식량에서 저항 변화율을 크게 향상 시킨 프로브이다. 이 프로브는 좁은 선폭(O.25-1mm)의 세선을 복수개 포함한 형상으로 프로브를 설계하여 핏팅이 발생하면 하나의 세선이 끊어지도록 하여 국부적인 부식이 일어날 경우에도 저항변화가 크게 나타나도록 고안되었다. 탄소강의 경우 일반적인 환경에서는 부식속도가 결정립의 크기, 가공경화의 정도등 에 민감하게 변화되지 않는 것으로 알려져 있으나, 박막으로 증착되었을 경우에는 별 크재료와는 전혀 다른 미세구조를 가지므로 벌크의 부식거동과는 다른 거동을 보일 수 있다. 이 연구에서는 증착조건을 달리하여 증착된 철 박막의 결정성, 비저항, 표면 상태, 조성등을 4 point 프로브, SEM, Auger spectroscopy등을 이용하여 조사하고 각각의 전위, 부식속도등과의 상관관계를 조사하였다. 증착된 박막의 비저항은 증착중 혼입된 산소의 양에 따라 매우 민감하게 변화하였다. 산소가 l0at%이상 함유된 철은 강의 알려진 비저항보다 수십배 높은 비저항을 보이며, 부식전위가 높아지고 실제 부식속도 또한 매우 낮게 나타났다. 박막의 부식거동은 미량 불순물에 의해서도 크게 변화하였는데 동일한 수준의 비저 항을 갖는 철 박막에서도 99.9% 순도의 철을 타켓으로 하여 증착된 막은 일반 저탄소 강을 타켓으로 하여 증착된 막보다 훨씬 낮은 부식속도를 보였다.