• Geophysics and Geophysical Exploration
• /
• v.19 no.4
• /
• pp.187-199
• /
• 2016

In order to delineate the soft ground distribution, an integrated geostatistical analysis was performed using the MASW (Multichannel Analysis of Surface Wave) which has the information of overall region and CPTu (Piezo Cone Penetration Test) which provides the direct information of the measuring point of the ground. MASW results were known to have close relationship with the ground stiffness. This correlation was confirmed through the comparison of MASW data obtained from two survey lines to the laboratory test with extracted soil samples. 3D physical property distribution in the study area was acquired by geostatistical integrated analysis with the data of tip resistance ($q_c$) and pore pressure (u) from the CPTu obtained at 6 points within the study area. The integrated analysis was conducted by applying the COSGSIM (Sequential Gaussian Co-Simulation) technology which can carry out the simulation in accordance with the spatial correlation between the MASW results and both tip resistance and pore pressure. Besides the locations of CPTu, borehole investigations were also conducted at two different positions. As a result, the N value of SPT and borehole log could be secured, so these data were used for the analysis of the geotechnical engineering accuracy of the integrated analysis result. For the verification of reliability of the 3D distribution of tip resistance and pore pressure secured through integrated analysis, the geotechnical information gained from the two drilling areas was compared, and the result showed extremely high correlation.

• Geophysics and Geophysical Exploration
• /
• v.8 no.4
• /
• pp.237-242
• /
• 2005

A seismic refraction study in estimation of depth to the bedrock demonstrates that 1) the average velocity in the medium is about 250 m/s in the surface layer (< 4 m), 2,500 m/s in the weathered formation, and greater than 3,000 m/s in the bedrock, 2) the depth to the deepest reflector assumed to be the bedrock is about 17 m; however, according to the cores collected in a borehole in study area, the bedrock (granite) occurred at depth 25 m, 3) according to the density and velocity logging, at depth 17 m, a measurable velocity and density increase are observed, and 4) the velocity of the weathered formation is relatively high and therefore, the acquisition offsets ($70{\sim}80m$) are turned out not to be long enough to record the refracted signal from the bedrock at depth 25 m as first arrivals.

• The Journal of Engineering Geology
• /
• v.23 no.4
• /
• pp.329-340
• /
• 2013

A geologic survey of the Bukpyeong and Pohang basins, as candidate basins for the geological storage of $CO_2$, was performed to evaluate storage capacity and security. To analyze the mechanical stability of the storage reservoir and cap rocks, we measured the porosity, seismic velocity, uniaxial strength, internal frictional angle, and Young's modulus of core samples recovered from the two basins. It is costly and sometimes impossible to conduct tests over the entire range of drill holes, and continuous logging data do not yield the mechanical parameters directly. In this study, to derive the mechanical properties of geologic formations from the geophysical logging data, we determined the empirical relations between the physical properties (seismic velocity, porosity, and dynamic modulus) and the mechanical properties (uniaxial strength, internal friction angle) of the core samples. From the comparison with our core test data, the best fits to the two basins were selected from the relations suggested in previous studies. The relations between uniaxial strength, Young's modulus, and porosity of samples from the Bukpyeong and Pohang basins are more consistent with certain rock types than with the locality of the basins. The relations between the physical and mechanical properties were used to estimate the mechanical rock properties of geologic formations from seismic logging data. We expect that the mechanical properties could also be used as input data for a modeling study to understand the mechanical instability of rock formations prior to $CO_2$ injection.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.775-784
• /
• 2009

Weathered foliation could act as a critical failure plane because this type of plane tend to have low roughness and long extensions. A big constructed slope at $\bigcirc\bigcirc$ road construction site was failed due to the block movement along a fault zone which is parallel to foliation. Tectonic activity reactivated a fault zone parallel to foliation, and the fault clay within the shear zone metamorphosed retrogressively to chrolite. The failed block moved when the block weigh lost the balancing with the resisting force of the retrogressively metamorphosed chrolite. Evaluating the three dimensional distribution of the foliation was critical for establishing a plan for the stabilization of the slope. For this purpose, 10 boreholes were drilled as a lattice distribution, and the BIPS analyses are performed at each boreholes. The fractures measured in the boreholes are projected into 15 cross sections and their distributions are analysed, using Fracjection software. The projection analyse show that the strike of the foliation gets dipper towards left side of the slope. This geometry indicates that there are more failure block geometry at left side of the slope. Potential failure planes are searched using the projection method, and these information are provided for further support design.

• The Journal of Engineering Geology
• /
• v.23 no.4
• /
• pp.457-465
• /
• 2013

We integrated and correlated datasets from surface and subsurface geophysics, drilling cores, and engineering geology to identify geological interfaces and characterize the joints and fracture zones within the rock mass. The regional geometry of a geologically weak zone was investigated via a fence projection of electrical resistivity data and a borehole image-processing system. Subsurface discontinuities and intensive fracture zones within the rock mass are delineated by cross-hole seismic tomography and analyses of dip directions in rose diagrams. The dynamic elastic modulus is studied in terms of the P-wave velocity and Poisson's ratio. Subsurface discontinuities, which are conventionally identified using the N value and from core samples, can now be identified from anomalous reflection coefficients (i.e., acoustic impedance contrast) calculated using a pair of well logs, comprising seismic velocity from suspension-PS logging and density from logging. Intensive fracture zones identified in the synthetic seismogram are matched to core loss zones in the drilling core data and to a high concentration of joints in the borehole imaging system. The upper boundaries of fracture zones are correlated to strongly negative amplitude in the synthetic trace, which is constructed by convolution of the optimal Ricker wavelet with a reflection coefficient. The standard deviations of dynamic elastic moduli are higher for fracture zones than for acompact rock mass, due to the wide range of velocities resulting from the large numbers of joints and fractures within the zone.

• The Journal of Engineering Geology
• /
• v.12 no.1
• /
• pp.23-34
• /
• 2002

Borehole image analysis has been carried out to obtain the detailed geological data by approach of direct observation. Direct application of borehole image analysis inevitably gives rise to a few of restriction of data acquisition due to the limited information within narrow borehole space. Considering the apparent dip of discontinuity surface depending upon the direction, the visualized program of two-dimensional subsurface discontinuities is coded. Borehole image analysis can compensate the distribution of subsurface discontinuity extending into the expected area of investigation. In order to draw subsurface profile in the proposed area of subsurface construction, visualized program is coded as a window GUI (Graphic User Interface) using Fortran and Visual Basic Programming languages. It is to open publicly for the usage of whoever is in want. Discontinuity distribution map is visualized along the Proposed line of tunnel in the Janggye-ri area, Jangsu-gun. Using the visualized program, the limited information from borehole spatially applies into analysis of overall subsurface structures, and the distributional characteristics of discontinuity anticipate at the proposed area. In addition, spacing and extension of joint and depth of discontinuity effecting tunnel safety can be visualized along the direction of the proposed tunnel. These lines of visualization apply design and construction of fundanmental structures.

• The Journal of Engineering Geology
• /
• v.7 no.3
• /
• pp.161-171
• /
• 1997

The exact information on geological structures and characteristics of the subsurface must be acquired to secure quality and safety of constructions. GPR technique, one of the most updated geophysical methods, is known for its applicability to shallow-depth underground surveys. The purpose of this study is to examine the usefulness of GPR method in constructions for detailed subsurface investigations, especially detecting the boundary between basement rock and its overburden. To find appropriate depths of the geological boundaries, it is necessary to obtain velocity of electromagnetic wave propagating into the ground. Wave velocity 0.096 m/ns estimated from velocity analysis using CMP gathers is used for depth conversion from time section. The depths of geological boundaries from GPR profiles are very well correlated with boring data. In addition, GPR survey has found some undulations of the geological boundaries due to weathering, which cannot be provided by conventional coring approaches.

• Proceedings of the Korean Society of Disaster Information Conference
• /
• 2015.11a
• /
• pp.162-165
• /
• 2015

본 연구는 ${\bigcirc}{\bigcirc}$ 공구 공유수면 매립공사 수행 중에 매립토량의 부족이 발생함에 따라 이를 대상으로 원인을 분석하고자 수행하였다. 매립지의 토량부족 원인을 파악하기 위해 설계 및 계측자료를 수집하여 시공 현황을 파악하고 지반조사를 통해 해안지역과 매립지반의 시료를 채취하여 성상분석과 원지반에 대한 공학적 특성을 비교 검토하였다. 특히. 현장 시추조사에 의한 경계면 분석과 토질 종류를 점성토, 사질토, 부유토로 구분하고 침하량 공식에 따라 발생량을 산출하였다. 구역의 구분은 설계 시와 동일한 조건에서 침하량을 계산하였고 설계 시 지반고가 침식과 퇴적으로 인해 일부 변경되어 설계시 지반고와 착공시 지반고를 구분하여 기재하고 각각의 침하량을 비교하였다.

• The Journal of Engineering Geology
• /
• v.31 no.2
• /
• pp.211-222
• /
• 2021

The magnitude 5.4 earthquake occurred in 2017 near 7.5 km north of Buk-gu, Pohang. In order to find out the characteristics of microtremor in Buk-gu, Pohang, Gyeongsangbuk-do, where earthquake damage occurred significantly, a total of 39 points were acquired to analyze the horizontal to vertical spectral ratio (HVSR). Microtremor vary from region to region, so the resonant frequency of the region is obtained by examining the microtremor. For Thickness analysis, we analyze the structure and properties of shear wave velocity (Vs) up to the underlying rock to compare resonance frequencies to match the horizontal to vertical spectral ratio (HVSR) analysis technique against nearby boring data. Using F₀ = V_s/4H with a resonance frequency of alluvium is 1.3 ± 0.07 Hz and a resonance frequency of Yeonil group is 0.69 ± 0.22 Hz, the alluvium thickness was found to be 26~30 m and the Yeonil group thickness was 170~250 m.

• Economic and Environmental Geology
• /
• v.43 no.3
• /
• pp.259-267
• /
• 2010

Resistivity logging instruments were designed to measure electrical resistivity of formation, which can be directly interpreted to provide water-saturation profile. Short and long normal logging measurements are made under groundwater level. In some investigation sites, groundwater level reaches to a depth of a few meters. It has come to attention that the proximity of groundwater level might distort short and long normal logging readings, when the measurements are made near groundwater level, owing to the proximity of an insulating air. This study investigates the effects of the proximity of groundwater level (and also the proximity of earth surface) on the normal by simulating normal logging measurements near groundwater level. In the simulation, we consider all the details of real logging situation, i.e., the presence of wellbore, the tool mandrel with current and potential electrodes, and currentreturn and reference-potential electrodes. We also model the air to include the earth’'s surface in the simulation rather than the customary choice of imposing a boundary condition. To obtain apparent resistivity, we compute the voltage, i.e., potential difference between monitoring and reference electrodes. For the simulation, we use a twodimensional, goal-oriented and high-order self-adaptive hp finite element refinement strategy (h denotes the element size and p the polynomial order of approximation within each element) to obtain accurate simulation results. Numerical results indicate that distortion on the normal logging is greater when the reference potential electrode is closer to the borehole and distortions on long normal logging are larger than those on short normal logging.