• Korean Journal of Ecology and Environment
• /
• v.47 no.4
• /
• pp.282-291
• /
• 2014

This study was conducted to make distribution model of the Red-crowned Crane and the White-naped Crane according to the anthropogenic and natural factors affecting distribution of crane in Cheorwon, Korea. It was investigated that the impact power and its range of the indirect anthropogenic influence to feeding flock density in cranes from the road, residential area, military facilities, civilian control zone (CCZ), greenhouse and natural influence such as roosting site and available feeding area. Available feeding area is the most important factor for the crane's feeding site selection. The feeding flock density of the cranes near the residential area was lower than that of area far from the area, and tended to increase within 2.5 km distance. The increasing tendencies of feeding flock density from military facilities and high traffic volume road were similar, but the density in military facilities increased within 800 m, and the density from high traffic volume road increased within 2 km. These results suggested that residential area, military facilities and the road with high traffic volume had significant effect on foraging densities to the certain range. As the distance from the road with low traffic volume and roosting site increased, feeding flock density tended to decrease. The density of Red-crowned crane and White-naped crane inside the CCZ were respectively higher than those of outside the CCZ, especially for the Red-crowned crane. As a result, density of Red crowned cranes inside the CCZ was 5.2 times higher than that of outside, while that of white-naped cranes was 2.2 times bigger. If the density of greenhouse is lower than $40km^{-2}$, crane's feeding flock density in the low greenhouses density area was higher than that of high greenhouses density area. However, there was no difference in the feeding flock density if the density of the green houses is higher than $40km^{-2}$. The model for the Red-crowned Crane was related with available feeding area, distance from residential area, civilian control zone and distance from high traffic road. The model of the White-naped Crane was related with available feeding area, distance from roosting site and distance from lake. Finally, the estimated feeding flock density of cranes significantly correlated with density model according to the natural and anthropogenic factors.

• Asian Journal of Turfgrass Science
• /
• v.18 no.3
• /
• pp.149-163
• /
• 2004

Physical and chemical properties of root zone mixes and methods of green construction are important considerations for improving turf grass quality for putting greens. This study compared Penncross creeping bentgrass (Agrostis palustris Huds.) performance as affected by three root zone construction systems with three amendments (sand, peat, and zeolite). The objective of this study was to determine if an amended California construction system would improve green performance during establishment (1998-1999) and maturation (2000-2001). Three treatments were tested: California ($100\%$ sand), USGA($90\%$ sand and $10\%$ peat, v/v), and California-Z ($85\%$ sand and $15\%$ zeolite, v/v). Treatments were arranged in a randomized complete block with four replicates. Physical and chemical properties of the root zone and bentgrass performance were compared for the treatments. The California-Z treatment had the highest saturated hydraulic conductivity, field infiltration rate and the lowest bulk density. It also had the highest cation exchange capacity and plant available nutrient concentrations among the three treatments. The California-Z treatment produced bentgrass quality and color during green establishment and maturation that were equal to or higher than the California treatment, and consistently higher than the USGA treatment. The addition of an inorganic amendment to the California system improved physical and chemical properties of the root zone and improved quality and color of bentgrass during green establishment. During green maturation, creeping bentgrass in the California-Z treatment was equal (6 of 15 sampling dates) or $20\%$ higher (9 of 15 dates) in quality compared to the California system.

• Korean journal of applied entomology
• /
• v.51 no.3
• /
• pp.235-243
• /
• 2012

Population dynamics of the American serpentine leafminer, Liriomyza trifolii (Burgess), were observed and modeled in order to compare the effects of air and tomato leaf temperatures inside a greenhouse using DYMEX model builder and simulator (pre-programed module based simulation programs developed by CSIRO, Australia). The DYMEX model simulator consisted of a series of modules with the parameters of temperature dependent development and oviposition models of L. trifolii were incorporated from pre-published data. Leaf surface temperatures of cherry tomato leaves (cv. 'Koko') were monitored according to three tomato plant positions (top, > 1.8 m above the ground level; middle, 0.9 - 1.2 m; bottom, 0.3 - 0.5 m) using an infrared temperature gun. Air temperature was monitored at the same three positions using a self-contained temperature logger. Data sets for the observed air temperature and average leaf surface temperatures were collected (top and bottom surfaces), and incorporated into the DYMEX simulator in order to compare the effects of air and leaf surface temperature on the population dynamics of L. trifolii. The initial population consisted of 50 eggs, which were laid by five female L. trifolii in early June. The number of L. trifolii larvae was counted by visual inspection of the tomato plants in order to verify the performance of DYMEX simulation. The egg, pupa, and adult stage of L. trifolii could not be counted due to its infeasible of visual inspection. A significant positive correlation between the observed and the predicted numbers of larvae was found when the leaf surface temperatures were incorporated into the DYMEX simulation (r = 0.97, p < 0.01), but no significant positive correlation was observed with air temperatures(r = 0.40, p = 0.18). This study demonstrated that the population dynamics of L. trifolii was affected greatly by the leaf temperatures, though to little discernible degree by the air temperatures, and thus the leaf surface temperature should be for a consideration in the management of L. trifolii within cherry tomato greenhouses.

• Journal of Animal Environmental Science
• /
• v.17 no.sup
• /
• pp.7-20
• /
• 2011

This study was conducted to analyze the mixing ratio of raw feed materials for the methane mitigation and also to identify the minimum rearing density for improving the productivity of beef calves as eco-friendly fodder. Raw materials used in this study for the formulation of feed for methane reduction were crushed corn and alfalfa along with other 21 species. In addition, to investigate the appropriate rearing density, 12 Hanwoo calves with average weight of 150 kg was selected and experiment was conducted for four months. Methane gas emission (Bo) is about 3-4 times less in TMR 4 compared to TMR 1, 2 and 3. Feed price calculated for TMR 4 ration was also affordable. In addition, all TMRs showed a normal ruminal pH. Disappearance rate was observed to be lower in TMR 4 as compared to TMR 1, 2 and 3, but methane production decreased by 24 to 37%. The result showed improved total body weight, average daily gain and feed conversion ratio in rearing low-density ($18m^2/head$), and general treatment ($9m^2/head$) compared to overcrowding treatment ($6m^2/head$). In addition, blood components (total protein, glucose, AST, ALT and GGT factors) involved in health and disease treatments and health-related nutrition metabolism are lower in the low-density and general treatment compared to the high density treatment. Postural development (development of body size) i.e., weight, height and width significantly increased in the low and general density treatment compared to high density treatment. Especially excellent improvement was observed in low-density treatment than the general treatment. Moisture content, colonic bacteria and coccidium are higher in low and high density treatments than in the general treatment. The adequacy for beef rearing density is considered to be more desirable in an area more than $6m^2/head$. In conclusion, present study suggests that possibility of methane reduction through adjusting mixed feed ration. Also, rearing density is also an important factor in the growth and development of beef calves.

• Korean Journal of Soil Science and Fertilizer
• /
• v.25 no.1
• /
• pp.99-107
• /
• 1992

Effects of the indigenous Vesicular-arbuscular mycurrhizal fungi(VAMF) on early growth response of greenhouse grown crops were experimented. This study was done to evaluate the benefit of indigenous VAMF inoculation on the early growth and the subsequent growth after transplanting of some crops such as cucumber, tomato, hot pepper, eggplant, and melon. Leaf area, shoot dry weight, and plant length of mycorrhizal greenhouse crops showed the tendency of significant or no significant increase over control plants receiving no inoculation. The levels of VA mycorrhizal colonization were increased with plant growth, and infection rates of horticultural crop except hot pepper around one week after transplanting were decreased, while that of 8 weeks after emergence of mycorrhizal seedlings were increased again and infected by around 50% at harvesting time. In spore densities in the rhizosphere soil of craps experimented, the number of spore ranged from $72.7{\pm}26.3$ to $100{\pm}10.3g^1$ on dried soil basis and high density showed in both cucumber and tomato. Total nitrogen contents in shoots were lower in the mycorrhizal plants than non-mycorrhizal one, whereas P uptake in mycorrhizal hot pepper and tomato were highly ramarkable. The K contents in the shoots of mycorrhizal cucumber and eggplent were highly enhanced. Inoculation of the indigenous VAMF enhanced shoot Ca and Mg in both tomoto and melon. The contents of Fe, Zn, Mn and Cu in shoots of mycorrhizal crops were higher than non-mycorrhizal plants and vice versa in case of eggplent. Inoculation of the indigenous VAMF to horticultural crops were effective for alleviation of transplanting shock, and pretransplanting infection improved subsequent growth by reducing the time required for establishment of a functional mycorrhizal symbiosis following transplanting.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.5
• /
• pp.47-56
• /
• 2014

In winter season, the pore water inside the ground freezes and thaws repetitively due to the cold air temperature. When the freezing-thawing processes are repeated on the ground, the change in soil particle structure occurs and thus the damage of the infrastructure may be following. This study was performed in order to investigate the stiffness change of soils due to the freeze-thaw by using elastic waves. Sand-silt mixtures are prepared with in the silt fraction of 40 %, 60 % and 80 % in weight and in the degree of saturation of 40 %. The specimens are placed into the square freezing-thawing cell by the temping method. For the measurement of the elastic waves, a pair of the bender elements and a pair of piezo disk elements are installed on the cell, and a thermocouple is inserted into soils for the measurement of the temperature. The temperature of the mixtures is decreased from $20^{\circ}C$ to $-10^{\circ}C$ during freezing, is maintained at $-20^{\circ}C$ for 18 hours, is gradually increased up to the room temperature of $20^{\circ}C$ to thaw the specimens. The shear waves, the compressional waves and the temperature are measured during the freeze-thaw process. The experimental result indicates that the shear and the compressional wave velocities after thawing are smaller than those of before freezing. The velocity ratio of after thawing to before freezing of shear wave is smaller than that of the compressional wave. As silt fraction increases from 40 % to 80 %, the shear and compressional wave velocities are gradually increased. This study suggests that the freezing-thawing process in unsaturated soil loosens the soil particle structure, and the shear wave velocity reflects the effect of freezing-thawing more sensitively than the compressional wave velocity.

• Journal of Radiation Protection and Research
• /
• v.40 no.4
• /
• pp.216-222
• /
• 2015

Facilities processing raw materials containing naturally occurring radioactive materials (NORM) may give rise to enhanced radiation dose to workers due to chronic inhalation of airborne particulates. Internal radiation dose due to particulate inhalation varies depending on particulate properties, including size, shape, density, and absorption type. The objective of the present study was to assess inhalation dose sensitivity to physicochemical properties of airborne particulates. Committed effective doses to workers resulting from inhalation of airborne particulates were calculated based on International Commission on Radiological Protection 66 human respiratory tract model. Inhalation dose generally increased with decreasing particulate size. Committed effective doses due to inhalation of $0.01{\mu}m$ sized particulates were higher than doses due to $100{\mu}m$ sized particulates by factors of about 100 and 50 for $^{238}U$ and $^{230}Th$, respectively. Inhalation dose increased with decreasing shape factor. Shape factors of 1 and 2 resulted in dose difference by about 18 %. Inhalation dose increased with particulate mass density. Particulate mass densities of $11g{\cdot}cm^{-3}$ and $0.7g{\cdot}cm^{-3}$ resulted in dose difference by about 60 %. For $^{238}U$, inhalation doses were higher for absorption type of S, M, and F in that sequence. Committed effective dose for absorption type S of $^{238}U$ was about 9 times higher than dose for absorption F. For $^{230}Th$, inhalation doses were higher for absorption type of F, M, and S in that sequence. Committed effective dose for absorption type F of $^{230}Th$ was about 16 times higher than dose for absorption S. Consequently, use of default values for particulate properties without consideration of site specific physiochemical properties may potentially skew radiation dose estimates to unrealistic values up to 1-2 orders of magnitude. For this reason, it is highly recommended to consider site specific working materials and conditions and use the site specific particulate properties to accurately access radiation dose to workers at NORM processing facilities.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.24 no.3
• /
• pp.73-82
• /
• 2021

Rural roads are the significant infrastructure for developing and managing the rural areas, hence the utilization of the remote sensing datasets for managing the rural roads is necessary for expanding the rural transportation infrastructure and improving the life quality of the rural residents. In this research, the two different methods such as image classification and image segmentation were compared for mapping the rural road based on the given high-resolution satellite image acquired in the rural areas. In the image classification method, the deep learning with the multiple neural networks was employed to the given high-resolution satellite image for generating the object classification map, then the rural roads were mapped by extracting the road objects from the generated object classification map. In the image segmentation method, the multiresolution segmentation was employed to the same satellite image for generating the segment image, then the rural roads were mapped by merging the road objects located on the rural roads on the satellite image. We used the 100 checkpoints for assessing the accuracy of the two rural roads mapped by the different methods and drew the following conclusions. The image segmentation method had the better performance than the image classification method for mapping the rural roads using the give satellite image, because some of the rural roads mapped by the image classification method were not identified due to the miclassification errors occurred in the object classification map, while all of the rural roads mapped by the image segmentation method were identified. However some of the rural roads mapped by the image segmentation method also had the miclassfication errors due to some rural road segments including the non-rural road objects. In future research the object-oriented classification or the convolutional neural networks widely used for detecting the precise objects from the image sources would be used for improving the accuracy of the rural roads using the high-resolution satellite image.

• Journal of Bio-Environment Control
• /
• v.30 no.3
• /
• pp.237-243
• /
• 2021

The objective of this study was to evaluate the effect of stem number on plant growth, fruit quality, and yield of sweet peppers grown in greenhouses under supplemental lighting in winter. The seedlings were transplanted at 3.2 plants·m^-2 on October 26, 2020, and started supplemental lighting with 32 high pressure sodium lamps for 16-hour photoperiod from December 1, 2020 to May 25, 2021. Stems were differently trained with 2 and 3 numbers after branching nodes were developed. In the final harvest, the plant height was significantly shorter in the 3 stem-plants than in the 2 stem-plants. The number of nodes per stem and the leaves per plant were increased in the 3 stem-plants than in the 2 stem-plants, while the leaf area was less affected. There were no significant differences in the dry mass of leaves, stems, and immature fruits between the 2 and 3 stem-plants. The fruit fresh weight and fruit dry weight in the 3 stem-plants were decreased by 17% and 12% at 156 days after transplanting (DAT), and by 17% and 15% at 198 DAT compared to those in the 2 stem-plants, respectively. The marketable fruit rates were 93.6% and 95.4% in the 2 and 3 stem-plants, respectively. The total fruit yield in the 3 stem-plants was increased by 30.2% as compared to that in the 2 stem-plants. We concluded that the 3-stem-training cultivation positively affected the total fruit yield by sustaining adaptive vegetative growth of the plants. This result will help producers make useful decisions for increasing productivity of sweet peppers in greenhouses.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.51 no.3
• /
• pp.21-36
• /
• 2023

As a solution to environmental issues, such as climate change response, the carbon neutrality strategy, urban heat islands, fine dust, and biodiversity enhancement, the value of urban green spaces and trees are becoming important, and various studies dealing with the effects of trees for environmental improvement are being conducted. This study comprehensively considers the preceding studies on planting tree species, planting structure, planting density, and planting base to propose a direction for the planting renewal of green areas in urban parks and applies the findings to a renewal plan to improve the urban environment through landscaping trees. A field survey was conducted on the planting status of Seoul Children's Grand Park, a large-scale neighborhood park in Seoul, and based on the survey data, a planting function evaluation was conducted, and areas needing improvement in planting function were identified. The planting function evaluation was carried out considering the park function setting, planting concept according to spatial function, and planting status. As a result of the study, the direction of planting renewal according to functional change was derived for each stage of planting function evaluation. Increasing the green area ratio is a priority in setting up park functions, but user convenience should also be considered. As a concept of planting, visual landscape planting involves planting species with beautiful tree shapes, high carbon absorption, and fine dust reduction effects. Ecological landscape planting should create a multi-layered planting site on a slope. Buffer planting should be created as multi-layered forests to improve carbon absorption and fine dust reduction effects. Green planting should consist of broad-leaved trees and herbaceous layers and aim for the natural planting of herbaceous species. For plant species, species with high urban environment improvement effects, local native species, and wild bird preferred species should be selected. As for the planting structure, landscape planting sites and green planting sites should be composed of trees, shrubs, and trees and herbaceous layers that emphasize ecology or require multi-layered buffer functions. A higher standard is applied based on the planting interval for planting density. Installing a rainwater recycling facility and using soil loam for the planting base improves performance. The results of this study are meaningful in that they can be applied to derive areas needing functional improvement by performing planting function evaluation when planning planting renewal of aging urban parks and can suggest renewal directions that reflect the paradigm of functional change of created green areas.