• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.6
• /
• pp.124-131
• /
• 2014

This paper describes a design of an adaptive baseband modem based on TDMA(time division multiple access) with a relay protocol function for wireless personal area networks. The designed baseband modem is controlled by a master synchronization signal and can be configured a relay network up to 14 hops. For efficient data relay communications, the internal buffer design is optimized by implementing a priority memory bus controller to a single port memory. And the priority memory bus controller is also designed to minimize the number of synthesized logic gates. To implement the synchronization function of the narrowband TDMA relay communication, the number of gates has been reduced by dividing the frame synchronization circuits and the network slot synchronization circuits. By using these methods, the number of gates are used about 37%(34,000 gates) on Xilinx FPGA XC6SLX9 which has 90,000 gates. For the 1024-bit frame size with a 32-bit synchronization word, the communication reception rate is 96.4%. The measured maximum transmission delay of the designed baseband modem is 230.4 msec for the 14-hop relay communication.

• Journal of IKEEE
• /
• v.22 no.1
• /
• pp.38-45
• /
• 2018

An integrated cryptographic processor that efficiently integrates ARIA, AES block ciphers and Whirlpool hash function into a single hardware architecture is described. Based on the algorithm characteristics of ARIA, AES, and Whirlpool, we optimized the design so that the hardware resources of the substitution layer and the diffusion layer were shared. The round block was designed to operate in a time-division manner for the round transformation and the round key expansion of the Whirlpool hash, resulting in a lightweight hardware implementation. The hardware operation of the integrated ARIA-AES-Whirlpool crypto-processor was verified by Virtex5 FPGA implementation, and it occupied 68,531 gate equivalents (GEs) with a 0.18um CMOS cell library. When operating at 80 MHz clock frequency, it was estimated that the throughputs of ARIA, AES block ciphers, and Whirlpool hash were 602~787 Mbps, 682~930 Mbps, and 512 Mbps, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.2C
• /
• pp.182-192
• /
• 2010

This paper proposes the hardware IP design of JBIG2 encoder. In order to facilitate the next generation FAX after the standardization of JBIG2, major modules of JBIG2 encoder are designed and implemented, such as symbol extraction module, Huffman coder, MMR coder, and MQ coder. ImpulseC Codeveloper and Xilinx ISE/EDK program are used for the synthesis of VHDL code. To minimize the memory usage, 128 lines of input image are processed succesively instead of total image. The synthesized IPs are downloaded to Virtex-4 FX60 FPGA on ML410 development board. The four synthesized IPs utilize 36.7% of total slice of FPGA. Using Active-HDL tool, the generated IPs were verified showing normal operation. Compared with the software operation using microblaze cpu on ML410 board, the synthesized IPs are better in operation time. The improvement ratio of operation time between the synthesized IP and software is 17 times in case of symbol extraction IP, and 10 times in Huffman coder IP. MMR coder IP shows 6 times faster and MQ coder IP shows 2.2 times faster than software only operation. The synthesized H/W IP and S/W module cooperated to succeed in compressing the CCITT standard document.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.11A
• /
• pp.909-917
• /
• 2009

In this paper, we proposed and implemented the method to efficiently generate TDD synchronization signal and the digital circuit for the RF repeater which can eliminate the shadow region in the wireless communication field using the time division duplex (TDD) method. After detecting the TDD signal from the transmitted or received RF signal, the detected TDD signal is fed to the RF repeater for the normal operation. The proposed technique detects the envelop of the downlink signal and amplifies the detected envelop, and then restores the degraded envelop with the proposed digital filtering method. Finally the restored envelop is manipulated to the TDD synchronization signal. Our focus on the proposed algorithm is to develop it with simple feature and low cost but robust performance. The proposed scheme was implemented to the integrated system which has both RF and digital circuit and tested under the same condition with the commercial WiBro service.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.7
• /
• pp.21-28
• /
• 2017

Practical models for FPGA architectures which include performance- and/or density-enhancing components such as carry chains, wide function multiplexers, and memory/multiplier blocks are being applied to academic FPGA placement tools which used to rely on simple imaginary models. Previously the techniques such as pre-packing and multi-layer density analysis are proposed to remedy issues related to such practical models, and the wire length is effectively minimized during initial analytic placement. Since timing should be optimized rather than wire length, most previous work takes into account the timing constraints. However, instead of the initial analytic placement, the timing-driven techniques are mostly applied to subsequent steps such as placement legalization and iterative improvement. This paper incorporates the timing driven techniques, which check if the placement meets the timing constraints given in the standard SDC format, and minimize the detected violations, with the existing analytic placer which implements pre-packing and multi-layer density analysis. First of all, a static timing analyzer has been used to check the timing of the wire-length minimized placement results. In order to minimize the detected violations, a function to minimize the largest arrival time at end points is added to the objective function of the analytic placer. Since each clock has a different period, the function is proposed to be evaluated for each clock, and added to the objective function. Since this function can unnecessarily reduce the unviolated paths, a new function which calculates and minimizes the largest negative slack at end points is also proposed, and compared. Since the existing legalization which is non-timing driven is used before the timing analysis, any improvement on timing is entirely due to the functions added to the objective function. The experiments on twelve industrial examples show that the minimum arrival time function improves the worst negative slack by 15% on average whereas the minimum worst negative slack function improves the negative slacks by additional 6% on average.