• Radiation Oncology Journal
• /
• v.19 no.1
• /
• pp.66-73
• /
• 2001

Purpose : For the research of Boron Neutron Capture Therapy (BNCT), fast neutrons generated from the MC-50 cyclotron with maximum energy of 34.4 MeV in Korea Cancer Center Hospital were moderated by 70 cm paraffin and then the dose characteristics were investigated. Using these results, we hope to establish the protocol about dose measurement of epi-thermal neutron, to make a basis of dose characteristic of epi-thermal neutron emitted from nuclear reactor, and to find feasibility about accelerator-based BNCT. Method and Materials : For measuring the absorbed dose and dose distribution of fast neutron beams, we used Unidos 10005 (PTW, Germany) electrometer and IC-17 (Far West, USA), IC-18, ElC-1 ion chambers manufactured by A-150 plastic and used IC-l7M ion chamber manufactured by magnesium for gamma dose. There chambers were flushed with tissue equivalent gas and argon gas and then the flow rate was S co per minute. Using Monte Carlo N-Particle (MCNP) code, transport program in mixed field with neutron, photon, electron, two dimensional dose and energy fluence distribution was calculated and there results were compared with measured results. Results : The absorbed dose of fast neutron beams was $6.47\times10^{-3}$ cGy per 1 MU at the 4 cm depth of the water phantom, which is assumed to be effective depth for BNCT. The magnitude of gamma contamination intermingled with fast neutron beams was $65.2{\pm}0.9\%$ at the same depth. In the dose distribution according to the depth of water, the neutron dose decreased linearly and the gamma dose decreased exponentially as the depth was deepened. The factor expressed energy level, $D_{20}/D_{10}$, of the total dose was 0.718. Conclusion : Through the direct measurement using the two ion chambers, which is made different wall materials, and computer calculation of isodose distribution using MCNP simulation method, we have found the dose characteristics of low fluence fast neutron beams. If the power supply and the target material, which generate high voltage and current, will be developed and gamma contamination was reduced by lead or bismuth, we think, it may be possible to accelerator-based BNCT.

• Journal of KIISE:Computer Systems and Theory
• /
• v.34 no.5_6
• /
• pp.257-266
• /
• 2007

In On-Chip bus, the arbitration scheme is one of the critical factors that decide the overall system performance. The arbitration scheme used in traditional shared bus is the master-side arbitration based on the request and grant signals between multiple masters and single arbiter. In the case of the master-side arbitration, only one master and one slave can transfer the data at a time. Therefore the throughput of total bus system and the utilization of resources are decreased in the master-side arbitration. However in the slave-side arbitration, there is an arbiter at each slave port and the master just starts a transaction and waits for the slave response to proceed to the next transfer. Thus, the unit of arbitration can be a transaction or a transfer. Besides the throughput of total bus system and the utilization of resources are increased since the multiple masters can simultaneously perform transfers with independent slaves. In this paper, we implement and analyze the arbitration schemes for the Multi-Layer AHB BusMatrix based on the slave-side arbitration. We implement the slave-side arbitration schemes based on fixed priority, round robin and dynamic priority and accomplish the performance simulation to compare and analyze the performance of each arbitration scheme according to the characteristics of the master and slave. With the performance simulation, we observed that when there are few masters on critical path in a bus system, the arbitration scheme based on dynamic priority shows the maximum performance and in other cases, the arbitration scheme based on round robin shows the highest performance. In addition, the arbitration scheme with transaction based multiplexing shows higher performance than the same arbitration scheme with single transfer based switching in an application with frequent accesses to the long latency devices or memories such as SDRAM. The improvements of the arbitration scheme with transaction based multiplexing are 26%, 42% and 51%, respectively when the latency times of SDRAM are 1, 2 and 3 clock cycles.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.10 no.2
• /
• pp.67-85
• /
• 2007

A three-dimensional hydrodynamic model with the fine grid is applied to simulate the barotropic tides, tidal currents, residual currents and salinity dispersions in the Yellow Sea and the East China Sea. Data inputs include seasonal hydrography, mean wind and river input, and oceanic tides. Computed tidal distributions of four major tides($M_2,\;S_2,\;K_1$ and $O_1$) are presented and results are in good agreement with the observations in the domain. The model reproduces well the tidal charts. The tidal residual current is relatively strong around west coast of Korea including the Cheju Island and southern coast of China. The current by $M_2$ has a maximum speed of 10 cm/s in the vicinity of Cheju Island with a anti-clockwise circulation in the Yellow Sea. General tendency of the current, however, is to flow eastward in the South Sea. Surface residual current simulated with $M_2$ and with $M_2+S_2+K_1+O_1$ tidal forcing shows slightly different patterns in the East China Sea. The model shows that the southerly wind reduces the southward current created by freshwater discharge. In summer during high runoff(mean discharge about $50,000\;m^3/s$ of Yangtze), low salinity plume-like structure(with S < 30.0 psu) extending some 160 km toward the northeast and Changjiang Diluted Water(CDW), below salinity 26 psu, was found within about 95 km. The offshore dispersion of the Changjiang outflow water is enhanced by the prevailing southerly wind. It is estimated that the inertia of the river discharge cannot exclusively reach the around sea of Cheju Island. It is noted that spatial and temporal distribution of salinity and the other materials are controlled by mixture of Changjiang discharge, prevailing wind, advection by flowing warm current and tidal current.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.3
• /
• pp.421-435
• /
• 2017

Recently, due to the saturation of ground structures and the overpopulation of pipeline facilities requires to development of underground structures as an alternative to ground structures. Thus, mechanized tunnel construction of the shield TBM method has been increasing in order to prevent vibration and noise problems in construction of the NATM tunnel for the urban infrastructure construction. Tunnel construction plan for the tunnel line should be formed in a sharp curve to avoid building foundation and underground structures and it is inevitable to develop a shield TBM technology that suits the sharp curve tunnel construction. Therefore, this study is about the structural stability technology of the articulation jack, shield jack and skin plate for the shield TBM thrust in case of the mechanized tunnel construction that is a straight and sharp curve line. The construction case study and shield TBM operation principle are examined and analyzed by the theoretical approach. The torque of the cutter head, the thrust of the articulation jack and the shield jack, the amount of over cutting for curve is important respectively in shield TBM construction of straight and sharp curve line. In addition, it is very important to secure the stability of the skin plate structure to ensure the safety of the inside worker. This study examines the general structure and construction of the equipment, experimental simulation was carried out through numerical analysis to examine the main factors and structural stability of the skin plate structure. The structural stability of the skin plate was evaluated and optimizes the shape by comparing the loads of the articulation jack by selecting the virtual soil to be applied in a straight and sharp curve line construction. Since the present structure and operation method of the shield TBM type in domestic constructions are very similar, this study will help to develop the localized shield TBM technology for the new equipment and the vulnerability and stability review.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.4
• /
• pp.347-365
• /
• 2020

In order to resolve traffic problems in urban areas and to increase the area of green spaces, tunnels in downtown areas are being increased. Additionally, the application of large port smoke extraction ventilation systems is increasing as a countermeasure to smoke extraction ventilation for tunnels with high potential for traffic congestion. It is known that the smoke extraction performance of the large port smoke extraction system is influenced not only by the amount of the extraction flow rate, but also by various factors such as the shape of the extraction port (damper) and the extraction air velocity through a damper. Therefore, in this study, the design standards and installation status of each country were investigated. When the extraction air flow rate was the same, the smoke extraction performance according to the size of the damper was numerically simulated in terms of smoke propagation distance, compared and evaluated, and the following results were obtained. As the cross-sectional area of the smoke damper increases, the extraction flow rate is concentrated in the damper close to the extraction fan, and the smoke extraction rate of the damper in downstream decreases, thereby increasing the smoke propagation distance on the downstream side. In order to prevent such a phenomenon, it is necessary to reduce the cross-sectional area of the smoke damper and increase the velocity of passing air through the damper so that the pressure loss passing through the damper increases, thereby reducing the non-uniformity of smoke extraction flow rate in the extraction section. In this analysis, it was found that when the interval distance of the extraction damper was 50 m, the air velocity passing through damper was 4.4 m/s or more, and when the interval distance of the extraction dampers was 100 m, the air velocity passing through damper was greater than 4.84 m/s, it was found to be advantageous to ensure smoke extraction performance.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.9
• /
• pp.14-23
• /
• 2010

This paper reports the fabrication of a DVB-T/H System in Package (SiP) that is able to receive and process the DVB-T/H signal. The DVB-T/H is the European telecommunication standard for Digital Video Broadcasting (DVB). An IC-embedded Printed Circuit Board (PCB) process, interpose a chip between PCB layers, has applied to the DVB-T/H SiP. The chip inserted in DVB-T/H SiP is the System on Chip (SoC) for mobile TV. It is comprised of a RF block for DVB-T/H RF signal and a digital block to convert received signal to digital signal for an application processor. To operate the DVB-T/H IC, a 3MHz DC-DC converter and LDO are on the DVB-T/H SiP. And a 38.4MHz crystal is used as a clock source. The fabricated DVB-T/H SiP form 4 layers which size is $8mm{\times}8mm$. The DVB-T/H IC is located between 2nd and 3rd layer. According to the result of simulation, the RF signal sensitivity is improved since the layout modification of the ground plane and via. And we confirmed the adjustment of LC value on power transmission is necessary to turn down the noise level in a SiP. Although the size of a DVB-T/H SiP is decreased over 70% than reference module, the power consumption and efficiency is on a par with reference module. The average power consumption is 297mW and the efficiency is 87%. But, the RF signal sensitivity is declined by average 3.8dB. This is caused by the decrease of the RF signal sensitivity which is 2.8dB, because of the noise from the DC-DC converter.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.6
• /
• pp.1075-1082
• /
• 2016

In order to calculate the optimum installation interval between a speed hump and hump type crosswalk that are installed continuously in succession, this study examined the speed of a vehicle that passes different intervals between speed humps and hump type crosswalks from the approach section of a roundabout having a maximum speed limit of 30km/h; analyzed the effects of speed humps and hump type crosswalks installed continuously in succession on vehicle driving speed; and simulated the optimum installation height of hump type crosswalk. As a result, the following conclusion was drawn. First, it was found that the optimum interval between a speed hump and hump type crosswalk, which are the representative traffic calming techniques for reducing vehicle speed, to control vehicle speed under 30km/h is 30m. Second, as a result of comparing the deceleration of a vehicle that pass hump type crosswalks, it was found that if the installation interval is 65 m and above, a speed hump and hump type crosswalk had no effect. Therefore, it is desirable that the maximum installation interval between a speed hump and hump type crosswalk for controlling vehicle speed within a fixed road section should not exceed 65m. Third, the analysis showed that the optimum installation height of hump type crosswalk is 6-8cm in case vehicle speed at the approach section is 20km/h or lower, 8-10cm in case of 30km/h, and 10cm in case of 30km/h or higher, respectively. Fourth, even at a road section on which a speed hump and hump type crosswalk are installed, speed reduction effects may sometimes be insignificant due to a driver's studying effect, traffic conditions and so on. Thus, it is judged that speed reduction effects will be greater if several traffic calming techniques such as speed hump, chicane, and choker are applied at the same time. Therefore, in case of applying traffic calming techniques for the purpose of reducing vehicle speed in order to promote pedestrian safety, the composite application of several techniques should be considered.

• Journal of Biomedical Engineering Research
• /
• v.23 no.3
• /
• pp.253-261
• /
• 2002

A spatially adaptive falter was formulated to imrove PET image qualify and the Performance of the filter was evaluated using simulation and phantom and human PET studies. In the proposed filter. if a pixel was identified as the edge Pixel, the Pixel value was Preserved. Otherwise a Pixel was replaced by the mean of the pixel values weighted by 2:7: 2. A Pixel was identified as the edge Pixel. if it satisfies the following conditions : the number of ADs (absolute difference between center and neighborhood pixels) which is smaller than THl (($pix_max{\times}0.1/log_2(NPM)$, NPM : mean of 6 neighborhood pixels excluding minimum and maximum) is 8-k and the number of ADs which is lager than TH2 ($NPM{\times}0.1$) is k. where k : 2, 3, …, 6. The results of this study demonstrate the superior performance of the Proposed titter compared to Gaussian fitter, weight median filter and subset averaged median filter. The proposed tittering method is simple but effective in increasing uniformity and contrast with minimal degradation of spatial resolution of PET images and thus. is expected to Provide improved diagnositc quality PET images .

• Journal of the Korean Society of Radiology
• /
• v.17 no.6
• /
• pp.827-833
• /
• 2023

CT(Computed Tomography) contrast agents are commonly used in general hospitals and university hospitals when taking radiographic examinations. The CT contrast medium contains a mixture of a substance called "Iodine", which absorbs radiation energy and makes it appear white in the CT image, further improving the image quality. In addition, the CT contrast agent, which moves like blood in the blood vessels, clearly differentiates it from muscle and water, so CT contrast agents are widely used in hospitals. These CT contrast agents absorb X-rays, but in order to absorb X-rays, they must have a high density or a high radiation absorption coefficient. Since the CT contrast agent is injected into the blood vessels, if the density is high, the blood vessels are strained and the patient is in shock. For this reason, it is necessary to match the density similar to that of water and always pay attention to side effects. In addition, the amount of CT contrast medium is adjusted according to the patient's body shape, and the remaining contrast medium is discarded. However, This study tried to find out the idea of recycling it as a radiation shielding material. Since the CT contrast medium has a high radiation absorption coefficient at a density similar to that of water, the amount to absorb radiation is adjusted, the amount of contrast medium and the amount of water are adjusted, and the amount of radiation absorbed is determined by mixing with water. In addition, a study was conducted to find out the result of the difference in radiation absorption in various ways by comparing the radiation quality coefficient and absorption coefficient with other substances or materials in an environmentally friendly method harmless to the human body by mixing CT contrast medium and water.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.61 no.1
• /
• pp.16-29
• /
• 2024

2014년 4월 18일 오전 8시 48분경 전라남도 병풍도 인근 해역에서 세월호는 전복된 후 침몰하였다. 사고 당시 이 배에는 승객 443명과 선원 및 승무원 33명 모두 476명이 타고 있었고, 이 중 미수습자 5명을 포함하여304명이 생명을 잃었다. 그 동안 공식적인 사고원인 규명활동이 꾸준히 진행되어 이 사고의 원인을 규명하기 위한 조사가 네 차례 있었다. 하지만 아직까지 사고 원인이 무엇인지 명쾌하게 밝혀지지 않고 있다. 이 글에서는 먼저 그동안 있었던 네 차례의 공식적인 세월호 사고원인 규명활동을 정리하였다. 가장 먼저 사고원인 규명활동을 전개한 해양안전심판원 특별조사부는 2014년 사고 직후부터 그해 12월까지 활동하였다. 특별조사부 최종보고서에는 화물의 과적과 평형수 적재 부족으로 인한 선박복원성 기준 미달, 타각의 대각도 조타와 장시간 유지로 인한 부적절한 조타, 화물의 부실한 고박으로 인한 화물의 이동, 수밀문의 관리 부실로 인한 조기 침수와 비상대피장소(muster station)로의 승객대피 조치 미이행을 사고의 원인으로 들고 있다. 2015년 3월부터 2016년 6월까지 활동한 4·16세월호참사 특별조사위원회(특조위)는 '4·16 세월호 참사 특별 조사위원회 청산 백서'만을 간행하고 최종보고서를 제출하지 못한 채 활동을 종료하였다. 세월호 선체조사위원회(선조위)는 2017년 4월부터 2018년 8월까지 활동하였다. 선조위는 세월호 사고원인 규명을 위한 다른 기구에 비해 위원의 구성도 균형이 있었고, 직권사건 위주의 조사방법도 적절하였다. 또한 조타기와 조타 과실 여부, 급선회 항적 및 횡경사와 핀안정기의 물리적 손상에 관한 용역을 국내 여러 기관에 발주하였다. 뿐만 아니라 다양한 해양사고 원인규명 용역에 참여한 실적이 있는 영국의 기술용역회사인 Brookes Bell에 급선회와 빠른 침몰의 원인 조사를 요청하였다. 아울러 세계에서 가장 활발히 수조실험을 수행하고 있는 상업 연구소인 네덜란드의 MARIN에 수조시험과 시뮬레이션도 의뢰하였다. 하지만 아쉽게도 선조위는 서로 다른 사고 원인을 주장하는 두 권의 종합보고서를 간행하였다. 종합보고서로 '내인설' 종합보고서[6]는 타기 솔레노이드 밸브의 고착으로 시작된 급선회를 사고의 직접 원인으로 지목하고 있다. 하지만 '열린안' 종합보고서[7]에서는 수중체와의 충돌을 직접적인 사고 원인으로 밝히고 있다. 마지막으로 가습기살균제 사건과 4·16세월호 참사 특별조사위원회(사참위)가 2019년 3월부터 2022년 9월까지 활동하였다. 사참위는 위원으로 조선해양공학과 항해학 전문가가 포함되어 있지 않아 세월호의 사고원인 규명활동을 효과적으로 수행하기에는 적절하지 못하였다. 사참위는 주로 조타장치 고장에 따른 세월호 전타 선회현상 검증, 세월호 변형 손상부의 확인 및 원인 조사와 세월호 횡경사 원인과 침수과정 분석을 직권 과제로 추진하였다. 또한 네덜란드 MARIN에 자유항주시험을 추가로 의뢰하였으며, 핀란드의 NAPA group에도 복원성 계산과 침수해석을 의뢰하였다. 사참위는 선조위의 두 가지 사고원인에 대해 '내인설'의 솔레노이드 밸브 고착은 사고원인일 가능성이 매우 낮고, '열린안'의 수중체와의 충돌 시나리오는 근거가 부족함을 확인하였다. 이상에서 정리한 바와 같이 규명활동이 진행됨에 따라 사고원인이 수렴되어야 함에도 불구하고 아직까지 원인을 시원하게 밝히지 못하고 있다. 이 글에서는 사고원인 규명활동을 수행한 네 개 기구의 구성과 활동 내용을 비교하고, 사고조사 위원회의 바람직한 구성과 위원회의 운영 방법을 제시하고 있다. 또한 Brookes Bell 보고서에 수록된 출항 당시의 흘수에 근거한 배수량과 선미 램프의 폐쇄 전후의 횡경사각으로부터 도출한 GoM도 소개하고 있다. 아울러 출항 당시의 GoM값으로 추정한 사고 당시의 GoM값도 소개하고 있고, 수중체와의 충돌 시나리오를 후보 사고 시나리오에서 제외시켜야 할 이유도 열거하고 있다. 끝으로 해양사고 원인규명 활동이 보다 과학적으로 그리고 보다 합리적으로 이루어질 수 있기 위해 그리고 우리 사회의 안전문화 제고를 위한 몇 가지의 방안을 제시하고 있다. 또한 세월호 사고로 치른, 아직도 치르고 있는 희생을 딛고 해양안전문화가 한 걸음 더 나아가기 위해서는 세월호 사고의 원인을 반드시 규명해야 한다는 말씀으로 글을 마무리하고 있다.