• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.32 no.2
• /
• pp.180-185
• /
• 1999

Rotating Biological Contactor (RBC) was tested for the treatment of artificial rearing water in n simulated aquaculture system. Performance of RBC on the removal of TAN and COD was evaluated by controlling hydraulic residence time (HRT). As HRT of RBC was increased, TAN removal rate ana removal efficiency of RBC and TAN concentration of rearing water were increased, but COD removal rate was decreased. Total alkalinity consumption rate was increased by increasing HRT of RBC. Ratio between total alkalinity consumption rate and TAN removal rate was 7.73. HRT for maintaining lowest TAN and COD concentration of artificial rearing water was 14,6 minutes and at that condition TAN and COD concentration of the water was 1.28 and $5.59 g/m^3$, respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.1
• /
• pp.140-152
• /
• 1997

A simultaneous measurement of the wall skin friction and near-wall streamwise velocity fluctuations is performed using hot film and hot wire anemometers to investigate the relation between them. Near-wall turbulence statistics measured with a hot-wire probe are in good agreement with previous results. Turbulence properties of the wall skin friction fluctuations measured with a hot film also show fairly good agreements with those measured by others except that rms level is lower in the present study. Long-time averaged space- time correlations show that the wall skin friction is highly correlated with a turbulence structure which is tilted from the wall in the streamwise direction. Tilting angles are obtained from the phase shifts between the wall skin-friction and streamwise velocity fluctuations. The convection velocity of the near-wall streamwise velocity obtained from the space-time correlation is in good agreement with that from the direct numerical simulation database.

• Journal of Korean Society of Transportation
• /
• v.14 no.2
• /
• pp.173-189
• /
• 1996

본 논문의 목적은 2차선 지방지역도로에서 사용 가능한 No-overtaking Model의 개발과 현장조사를 통한 우리 나라 2차선 도로의 교통류 특성의 규명이었다. No-overtaking Model을 개발하기 위해서는 이미 개발된 바 있는 Slow moving Vehicle Model의 이론적 틀을 근거로 하되 중차량을 따라 피동적으로 주행하는 일련의 차량군에 또 다른 중차량이 포함된 경우에 대해서도 분석이 가능하도록 개선했다. 경기도 일원에서 약 3 개월동안 조사한 현장조사에서 나타난 우리 나라 2차선 도로의 교통류 특성은 첫째로, 2차 선 교통류의 주요 MOE(Measures of Effectiveness)들은 교통량에 의해 비교적 정확하게 산정 가능하다는 것과, 둘째로 우리 나라의 주요 MOE값은 외국의 경우와 비교했을 때 대 체로 유사한 결가를 보이나 평균속도의 경우 최소 5km/h 최대 15km/h 정도와 차이를 나타 낸다는 것, 그리고 셋째로 차량군의 선두차량 85%의 경우 그 속도는 100.4km/h이고 추월 에 필요한 반대편차선 차량과의 여유 거리는 754.8m이라는 것이었다. 향후 연구과제로는 중차량의 속도분포를 확률 분포식으로 나타내는 경우의 지체시간, 추월율 등의 2차선 교통 류 MOE를 산출할 수 있는 Model을 개발하는 것이며 현재 5분 교통량으로 표시된 교통량 을 보다 많은 현장수집 자료를 통해 1시간 단위의 교통량을 기준으로 하여 MOE를 산정해 보는 것이다.

• Korean Journal of Applied Biomechanics
• /
• v.12 no.2
• /
• pp.345-359
• /
• 2002

The purpose of the study was to provide the fundamental data to instruct athletes through the analysis athletes' movement in javelin. Three athletes in the level of national representative were participated in this study. The study analyzed kinematic variables(lead foot and releasing javelin) through 3-D analysis and obtained the following results. 1. During withdrawal, it is important to maintain of running horizontal velocity. 2. It was showed that throng average height was $84{\pm}3.3%$ and javelin adequative degree, Among the athletes, $S_2$ who had the best record was released the javelin with the fast velocity, but throw the javelin with the less releasing velocity. 3. $S_2$ released after lead foot were completely landed and therefore it is no problem in a kinematic aspect. However, $S_1$ angle was too small. it caused increase of release velocity to be prevented. 4. $S_2$ showing the best result indicated shorter in duration time. Generally, the shorter duration time in release phase showed the longer release distance. Especially $S_1$ and $S_3$ showing the worse result indicated the longer duration time in preparatory phase, causing the breakup of force. Therefore to improve the record, it should be decreased the duration time in preparatory phase. 5. Compared with $S_1$ and $S_3$, $S_2$ showing the best record indicated the higher velocity in center of mass, trunk, upper arm, lower arm and hand That is the higher velocity of upper arm at release leaded the better velocity transfer from upper arm to following lower arm and hand, these action should be considered to be helpful of better record. According to the above conclusion, when the athletic leaders cauch athletes, they should focus on maintaining knee angle, upper body and hip angle in a previous stage of release and throwing angle, throwing height, throwing velocity in a release stage.

• Journal of Animal Science and Technology
• /
• v.51 no.4
• /
• pp.265-272
• /
• 2009

A total of 486 milk records were collected from 16 diary farms in Imsil-gun, Jeollabuk-do. Results obtained were as follows: The average 3MG (amount of milk within the first three minute) was 7.44 kg and 55% of total milk yield was produced within 3 min. The average of SPL (% of foam in milk) was 33.93% and the average of MNG (strip yield) was 0.14 kg, which was less than 1% of total milk yield. The averages of HMF (highest milk flow), HMG (maximum milk flow rate in one minute) and DMHG (average milk flow in the main milking phase) were 3.03 kg/min, 2.94 kg/min and 2.05 kg/min, respectively and the average milking speed in Imsil-gun was slower than other regions. The average of tS500(time to reach 0.5 kg/min at beginning) was 0.23min (about 14 seconds) and that of tMGG (duration of the total milking) was 7.75min. The average tMBG (duration of the dry milking phase) was 0.58 min (35 seconds) and that of tMNG (duration of the stripping phase) was 0.42min (14 seconds). The averages of ELHMF (electrical conductivity at highest milk flow) and ELAP (beginning peak level of the electrical conductivity) were 6.81 mS/cm and 7.58 mS/cm, respectively. The average of ELMAX (maximum electrical conductivity) was 7.48 mS/cm and that of ELAD (beginning peak difference of the electrical conductivity) was 0.61 mS/cm. While the total milk yields for DMHG, tMHG (duration of the main milking phase), tPL (duration of the plateau phase), tAB (duration of the descending phase) and tMGG were positively correlated (0.35~0.54), those for tMBG and SPL were negatively correlated (-0.11 and -0.27). As the DMHG increased, tMHG, tPL, tAB, tMGG and SPL decreased. While the cows with higher electrical conductivity at the beginning of milking had less somatic cell counts, cows with higher electrical conductivity after the peak of milk yield had more somatic cell counts. The results of this experiment indicated that through milking based on milking and lactating standards and the regular checking of milking status, the qualities of milk and milk yields could be improved.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.3
• /
• pp.405-415
• /
• 2000

Experiments for autotrophic denitrification were performed using an upf10w reac1.or packed with sulfur particles as an electron donor. The influent $NO_3{^-}$-N concentration was kept almost constant, but the hydraulic retention time(HRT) and temperature varied. Results of the research showed that the denitrification efficiency and gas generation rate decreased as the HRT and temperature were reduced. During the HRT effect experiment, alkalinities of 3.44~5.71g, with an average of 4.67 g which is close to the theoretical value of 4.57g were consumed for each gram of $NO_3{^-}$-N removed. During the temperature effect experiment, however, the values were 6.58~13.41 g with an average of 9.12 g which is almost twice the theoretical value Denitrification along the length of the reactor appeared to be a first-order reaction with a reaction rate constant of 0.1648/hr. On the other hand, the sulfate generation showed a zero-order reaction with a reaction rate constant of 241/hr. There was some discrepancy in the nitrogen mass balance between the theoretical and measured values, requiring further researches.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.555-559
• /
• 2009

난류응력은 순간속도성분을 시간평균성분과 편차성분의 합으로 보고 Navier-Stokes 방정식으로부터 Reynolds 방정식을 유도할 때 나타나게 된다. Reynolds 방정식으로부터 수심 적분된 천수방정식을 유도하는 과정에서 시간 평균된 유속성분을 수심 적분된 유속성분과 편차성분의 합으로 본다면, 분산응력 (dispersion stress)이라고 하는 추가적인 새로운 항이 잔류하게 된다. 점성응력, 난류응력, 그리고 분산응력을 통칭하여 유효응력 (effective stress)이라고 한다. 일반적으로 수심에 비해 수로 폭이 넓은 개수로에서는 유효응력이 흐름특성의 수치 근사해에 큰 영향을 미치지 못한다고 가정하여 2차원 수심적분 모형에서 유효응력을 생략하기도 한다. 또한 유효응력을 적용하더라도, 점성응력이 난류응력에 비해 무시할 만큼 작다고 가정하여 난류응력만을 적용하며, 분산응력은 무시된다. 하지만 만곡부에서는 원심력과 편수위로 인한 횡방향 압력의 불균형이 발생하기 때문에, 만곡부의 이차류가 발생되며, 유속의 연직방향 분포도 일정하지 않게 된다. 따라서 본 연구의 목적은 만곡부의 이차류 특성을 수심적분 2차원 모형에 반영하기 위해 분산응력을 고려한 모형의 개발 및 검증이다. 불규칙한 모의영역을 원활히 나타낼 수 있도록 곡선좌표계를 사용하는 여타 모형들과 달리 유한유소법을 이용하여 수치해를 구하며, 따라서 x, y 좌표축을 사용하는 데카르트 좌표계를 사용하여 지배방정식을 나타낸다. 분산응력의 유 무에 따른 수치결과를 Rozovskii의 $180^{\circ}$ 만곡수로 실내실험 자료와 비교하여 개발 모형을 검증한다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.157-158
• /
• 2011

Golf clubs hit the ball, and golf balls fly with great speed and long distances due to the conflict. In this paper, the size of the momentum after collision of golf clubs and golf balls should seek. Also, the collision times and average force that served of golf clubs and golf balls are obtained. We know that the impulse acting body is equals the change in momentum of a body. And you can see the average force is constant force that the actual strength of a body to give the same impulse instead of force changing by the hour.

• Solar Energy
• /
• v.18 no.2
• /
• pp.115-121
• /
• 1998

In this study a channel cavity flow was performed. The channel has small size in the upper cavity region. At the gap is supplied by driven flow for Reynolds number. The experimental study was carried out in a channel cavity with square heat surface by visualization equipment with Mach-Zehnder interferometer and laser apparatus. Heat source was uniform heat flux($0.4W/cm^2,\;0.8W/cm^2,\;1.2W/cm^2$). When the bottom wall is heated, the tendency of natural convection flows are vigorous increasing heat flux.

• Journal of Korean Ophthalmic Optics Society
• /
• v.19 no.4
• /
• pp.533-538
• /
• 2014

Purpose: This study is to investigate correlation between eye fatigue and letter contrast according to letter contrast changes on monitor display. Methods: Reading speed test were carried out for 53 subjects (mean age: $22.68{\pm}1.85$ years) who have over Best-corrected visual acuity (BCVA) 1.0, and 45 subjects, who could read over 123 out of 163 letters among 53 subjects were selected. They were asked to read the letters which were composed of Black (contrast 100%), Dark gray (contrast 80%), Gray (contrast 80%), Light gray (contrast 30%) randomly. The change of their eye fatigue by letter contrast on monitor display was measured by monitoring their eyes with an eye-tracker while they were reading letters. Results: Event Duration (sec) was 33.635 for Black, 32.266 Dark gray, 33.936 for Gray, and 34.848 for Light gray. Average of Fixation Duration (sec) was 0.224 for Black, 0.218 for Dark gray, 0.239 for Gray and 0.243 for Light gray. Average of Pupil diameter (mm) was 41.133 mm for Black, 41.160 mm for Dark gray, 40.880 mm for Gray and 40.459 mm for Light gray. Frequency (blinks/sec) was 0.211 for Black, 0.206 for Dark gray, 0.221 for Gray, and 0.238 for Light gray. Conclusions: Event Duration and average of Fixation Duration were the shortest for Dark gray and the longest for Light gray. In average Pupil diameter was the biggest Dark gray and the smallest for Light gray. Blink Frequency (blinks/sec) was the lowest for Dark gray and the highest for Light gray. Visual fatigue by brightness of letters on monitor display was the least for Dark gray followed by Black, Gray and Light gray.