• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.840-843
• /
• 2003

본 논문은 임의의 입력지연을 갖는 Takagi-Sugeno (T-S) 퍼지 시스템의 관측기 기반 출력궤환 제어 시스템을 논의한다. 설계된 연속시간 T-S 퍼지 관측기 시스템을 영차의 샘플/홀드 함수를 이용하여 이산시간 관측기를 설계한다. 이때 플랜트와 관측기의 출력에러가 제어기를 통하여 궤환되기 때문에 이산화 과정에서 발생한 에러를 보정할 수 있다. 여기에서 시스템의 제어 입력은 임의로 변화하는 유한개의 상태를 갖는 마코프 확률과정으로 표현한다. 생성된 시스템의 확률적 안정 가능성 조건은 선형 행렬 부등식의 형태로 표현한다. 이러한 결과를 2자유도 헬리콥터의 모델에 대한 모의실험을 통하여 효용성을 확인한다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.8
• /
• pp.627-636
• /
• 2021

This paper deals with a study for the guidance control of reusable launch vehicle. For this purpose, modeling of the equation of motion of a reusable launch vehicle with 6 degrees of freedom was performed. With this model, an optimal re-entry path was created and a path-following guidance control simulation was performed to follow the optimal re-entry path. For the design of the path-following guidance controller, the attitude controller applying a time-delay technique that is resistant to modeling uncertainty, disturbance and failure. And the nonlinear path-following guidance law were used. Guidance control simulation using a classical PD controller was performed and compared with the guidance control simulation of a reusable launch vehicle applying a time delay technique.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.39 no.6
• /
• pp.1-8
• /
• 2002

This paper presents a generalized minimum-variance self-tuning controller with a PID structure using neural network which adapts to the changing parameters of the nonlinear system with nonminimum phase behavior and time delays. The neural network is used to estimate the controller parameters, and the control output is obtained through estimated controller parameter. In order to demonstrate the effectiveness of the proposed algorithm, the computer simulation is done to adapt the nonlinear nonminimum phase system with time delays and changed system parameter after a constant time. The proposed method compared with direct adaptive controller using neural network.

• Aerospace Engineering and Technology
• /
• v.6 no.2
• /
• pp.1-7
• /
• 2007

The control design for attitude and yaw rate of 40 % scaled SMART UA Vhas been performed. Analytic selection method for a control gain is proposed to meet the design specification of desired time response considering stability margin. The sliding mode attitude controller is also proposed and compared with the simulation results of a linear controller. Additionally, a velocity and height tracking controller is devised to prepar for the flight test.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.43 no.3 s.309
• /
• pp.1-7
• /
• 2006

In this paper, a method for IMC-PID controller tuning is proposed based on obtaining a controller from closed-loop transfer function. It is considered a plant with the second-order plus dead time(SOPDT) model and selected the third-order plus dead time transfer function model as a target function. The filter function is derived from the suitable target function to satisfy the design specifications. A robustness test was done to verify the robust-stability.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.3
• /
• pp.223-230
• /
• 1999

A conventional sliding mode control approach is often impractical or difficult when it is applied to high order process b because the number of tuning parameters in the sliding mode controller increases with the order of the plant. C Camacho(l996) proposed a design method of a fixed structure sliding mode controller based on a first order plus dead t time approximation to the higher-order process. But, his method has such problems as chattering, over‘shoot, and c command following due to the Taylor the approximation en‘ors for the time delay term of the first order model. In this p paper, a new design technique for a sliding mode controller based on the modified Taylor approximation considered a w weight is developed to improve the Camacho's problems.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.755-761
• /
• 2017

In railways powered by AC power, the main circuit breaker (MCB) is used for supplying the electric power to the catenary of the vehicle. Generally, the main circuit breaker is located between the pantograph and the main transformer, and the phase of the power applied to the vehicle changes according to the operation timing of the main circuit breaker. The operation of the main circuit breaker should be actively controlled according to the phase of the power source, since the phase of the power causes unintended transient states in the vehicle's electrical system in the form of an inrush current and surge voltage. However, the MCB has a delay time when it operates which is not constant. Therefore, an intelligent controller is needed to predict the operation delay time and control the opening and closing of the MCB.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.2
• /
• pp.336-342
• /
• 2008

Simple tuning methods of PI, PD and PID controller are proposed for an integrating process with time delay. This is based on matching the coefficients of corresponding powers of s in the numerator and that in the denominator of the closed-loop transfer function. For set-point tracking problem, the derived controller is found to be a PD controller which is shown by Lee's tuning rule based on minimizing the performance indexes (ISE, IAE, ITAE) using a real-coded genetic algorithm. A method can be also proposed PI, PID controllers according to tuning parameter lambda $({\lambda})$ similar to IMC method. Simulation example is given to illustrate the set-point tracking and disturbance rejection performance of the proposed method.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.1
• /
• pp.105-110
• /
• 2017

This paper introduces a heave compensation system for offshore crane when it subjected to unexpected disturbances such as ocean waves, tidal currents or winds and their external force. The dynamic model consists of a crane which is considered to behave in the same manner as a rigid body, a hydraulic driven winch, an elastic rope and a payload. To keep the payload from moving upwards and downwards, PD(Proportional-Derivative) control was applied by using linearization. In order to achieve a better performance, the sliding mode control and the nonlinear generalized predictive control algorithm was applied according to the time-delay. As a result, the oscillating amplitude of the payload was reduced by the control algorithm. Considering the time-delay involved in the system to be one second, nonlinear generalized predictive controller with a robust controller was a suitable control algorithm for this heave compensation system because it made the position of te payload reach the desired position with the minimum error. This paper presented a control algorithm using the robust control and its simulation results.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.1
• /
• pp.33-39
• /
• 2007

LonWorks over IP (LonWorks/IP) virtual device network (VDN) is an integrated form of LonWorks device network and IP data network. LonWorks/IP VDN can offer ubiquitous access to the information on the factory floor and make it possible for the predictive and preventive maintenance on the factory floor. Timely response is inevitable for predictive and preventive maintenance on the factory floor under the real-time distributed control. The network induced uncertain time delay deteriorates the performance and stability of the real-time distributed control system on LonWorks/IP virtual device network. Therefore, in order to guarantee the stability and to improve the performance of the networked distributed control system the time-varying uncertain time delay needs to be compensated for. In this paper, under the real-time distributed control on LonWorks/IP VDN with uncertain time delay, a control scheme based on disturbance observer and ZPETC(Zero Phase Error Tracking Controller) phase lag compensator is proposed and tested through computer simulation. The result of the proposed control is compared with that of internal model controller (IMC) based on Smith predictor and disturbance observer. It is shown that the proposed control scheme is disturbance and noise tolerant and can significantly improve the stability and the tracking performance of the periodic reference. Therefore, the proposed control scheme is well suited for the distributed servo control for predictive maintenance on LonWorks/IP-based virtual device network with time-varying delay.