• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.11
• /
• pp.2251-2259
• /
• 2009

We propose an algorithm and system which generates 3D stereo image by composition of 2D image from 4 multiple clusters which 1 cluster was composed of 4 multiple cameras based on network. Proposed Schemes have a network-based client-server architecture for load balancing of system caused to process a large amounts of data with real-time as well as multiple cluster environments. In addition, we make use of JPEG compression and RAM disk method for better performance. Our scheme first converts input images from 4 channel, 16 cameras to binary image. And then we generate 3D stereo images after applying edge detection algorithm such as Sobel algorithm and Prewiit algorithm used to get disparities from images of 16 multiple cameras. With respect of performance results, the proposed scheme takes about 0.05 sec. to transfer image from client to server as well as 0.84 to generate 3D stereo images after composing 2D images from 16 multiple cameras. We finally confirm that our scheme is efficient to generate 3D stereo images in multiple view and multiple clusters environments with real-time.

• Resources Recycling
• /
• v.19 no.5
• /
• pp.31-43
• /
• 2010

To fabricate porous SiC candle filter for filtration facility of the IGCC system, the candle type filter preforms were fabricated by ramming and vacuum extrusion process. A commercially available ${\alpha}$-SiC powders with various particle size were used as starting raw materials, and $44\;{\mu}m$ mullite, $CaCO_3$ powder were used as non-clay based inorganic sintering additive. The candle typed preforms by ramming process and vacuum extrusion were sintered at $1400^{\circ}C$ for 2h in air atmosphere. The effect of forming method and particle size of filter matrix on porosity, density, strength (flexural and compressive strength) and microstructure of the sintered porous SiC candle tilters were investigated. The sintered porous SiC filters which were fabricated by ramming process have more higher density and strength than extruded filter in same particle size of the matrix, and its maximum density and 3-point bending strength were $2.00\;g/cm^3$ and 45 MPa, respectively. Also, corrosion test of the sintered candle filter specimens by different forming method was performed at $600^{\circ}C$ for 2400h using IGCC syngas atmosphere for estimation of long-term reliability of the candle filter matrix.

• Elastomers and Composites
• /
• v.49 no.1
• /
• pp.59-65
• /
• 2014

In this study, in order to complete curing reaction of the molding compound comprising an epoxy/anhydride at $71^{\circ}C$ for 40 hours, metal coordination complexes such as cobalt (II) acetylacetonate, potassium acetylacetonate, iron (III) acetylacetonate and chromium (III) octoate as a catalyst were applied to the epoxy/anhydride compounds respectively. The weight ratio of an epoxy part/an anhydride part was adjusted to improve the mechanical properties of the molding compound. According to the experimental results, an epoxy/anhydride compound containing chromium (III) octoate showed a high conversion at $71^{\circ}C$ for 40 hours as well as a proper processability at room temperature among the several metal coordination complexes. For the mechanical properties of the cured epoxy/anhydride compound, the compounds containing weight ratio from 0.9/1 to 0.5/1 of the epoxy part/anhydride part with chromium (III) octoate showed the high flexural strength, and higher compressive strength was shown with increasing of the hardener part.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.2
• /
• pp.50-61
• /
• 1988

접착제(接着劑) 제조(製造)를 위하여 펄프폐액(廢液)중의 리그닌을 이용(利用)하는 연구(硏究)가 1930년경(年傾)부터 진행(進行)되여 아황산펄프폐액(廢液)중의 Lignosulfonate의 경우는 페놀수지(樹脂)나 요소수지(要素樹脂)에 증량(增量)시키거난 반응(反應)시키는 연구(硏究)인데 비하여 kraft 리그닌을 이용(利用)하는 경우는 페놀수지(樹脂)의 보문(報文)이 주류(主流)를 이루고 있으나 요소계(要素系) 공축합수지(共縮合樹脂)는 아직 발표(發表)된 바 없으며 또한 아직까지 리그닌을 이용(利用)한 상업적(商業的)인 접착제(接着劑)가 제조(製造)되어 활용(活用)되지 못하고 있는 실정(實情)이다. 따라서 본(本) 연구(硏究)는 합판제조(合板製造)의 원가절감(原價節減), 폐액이용(廢液利用)의 환경보존관점(環境保存觀點)에서 Krfat Pulp 폐액(廢液)중의 리그닌접착제(接着劑)의 제조(製造)하고져 실시(實施)하였으며, Urea-Lignin 접착제(接着劑)의 도포량(塗布量)은 일반적(一般的)으로 합판(合板)에 도포(塗布)되는 요소수지(要素樹脂)의 량(量)(320g/$m^2$)과 동일(同一)하고 압축응력(壓縮應力)은 균일(均一)하게 12kg/$cm^2$으로 하여 열압조건(熱壓條件)(온도(溫度), 시간(時間))의 영향(影響))을 아울러 규명(糾明)하였다. Urea-Formaldehyde와 Kraft lignin의 혼합비(混合比)는 중량비(重量比)(N.V.C)로 7:3으로 합성수지(合成樹脂)를 만들어 합판제조(合板製造)를 통(通)하여 구명(究明)를 결과(結果) 다음과 같은 결론(結論)을 얻었다. 1. 본(本) 실험(實驗)의 결과(結果) 요소수지(要素樹脂)의 약(約) 30%가 krfat lignin으로 대체(代替)할 수 있음을 보여준 바, Pulping 공정(工程)의 부산물(副産物)로 얻어진 폐액(廢液)은 합판제조시(合板製造時) 접착제(接着劑)의 대체원(代替源)으로 유효(有效)하다. 2. 경제적관점(經濟的觀點)에서 합판제조(合板製造)를 위한 최적열압조건(最適熱壓條件)은 $160^{\circ}C$에서 3분(分)으로 압착(壓搾)하는 것이 적절(適切)하였다.(상태(常態)): 16.49kg/$cm^2$, 내수(耐水) : 18.56kg/$cm^2$, 내온수(內溫水) : 12.53kg/$cm^2$). 3. 요소-리그닌 접착제(接着劑)로 제조(製造)된 합판(合板)의 전단인장강도(剪斷引長强度)는 양호(良好)한 접착력(接着力)을 나타냈으며, 내수접착력(耐水接着力)($30^{\circ}C$에서 3시간(時間) 심적후(沈積後) 시험(試驗)은 상태접착력(狀態接着力)과 별차이가 없거나 더 높은 인장강도력(引長强度力)을 보여준 바, 내수합판용(耐水合板用) 접착제(接着劑)로 상당한 전망(展望)을 나타냈다.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.12
• /
• pp.65-75
• /
• 2017

Flowability and strength with curing time of controlled low-strength material (CLSM) are required differently according to the construction purpose. In this paper, the flowability and strength were estimated from the mixing ratio of CLSM using multiple regression analysis to design the CLSM. The flow values and strength at 12 hrs and 7days were measured in accordance with the mixing ratio of CLSM which consists of 7 different materials, such as CSA expansive agent, ordinary Portland cement, fly ash, sand, silt, water, and accelerator. The multiple regression was performed with the proportions of each material of CLSM as independent variables and the measured properties as dependent variables using SPSS Statistics 23 which is a statistical analysis program. The regression coefficients were estimated from the first to third order equation models for the materials. From the results, the third order model for the flow values and the first order models for 12hrs and 7days strength are the most appropriate models. This study suggests that the mixing ratio required for constructions may be effectively estimated from the regression models about the characteristics of CLSM, before performing experimental tests.

• Journal of the Korean Ceramic Society
• /
• v.34 no.2
• /
• pp.163-170
• /
• 1997

The retarding effects of MgSiF6.6H2O on the hydration of portland cement were studied. The setting time, flow value and compressive strength of mortar were measured and the mechanism of retardation was also studied by ion concentration in solution, SEM, BET, and X-ray diffraction. The results are as follows ; 1. Setting time was delayed by the addition of MgSiF6.6H2O. 2. The flow value of mortar decreases depending upon the amount of MgSiF6.6H2O. 3. The compressive strength was almost same or some increase on 28 days hydration. 4. The main retardation mechanism of MgSiF6 on the hydration of portland cement may be explained by the following hypothesis. MgSiF6 depressing the Ca++ and K+ ion concentration of cement paste solution be-cause of the recrystalization of K2SiF6 and CaF2 phase. The new products of K2SiF6 and CaF2 deposit on the surface of unhydrated cement powder and harzard the mass transfer through these layer. The low con-centration of Ca++, K+ ion in solution was decreasing the hydration rate of portland cement.

• Journal of the Korea Concrete Institute
• /
• v.25 no.3
• /
• pp.295-304
• /
• 2013

Ultra-High Performance Concrete (UHPC) has recently been one of the most active research fields in Korea as well as in foreign countries, because it can contribute to a longer life and economic efficiency of structures. Although precast-type UHPC fabricated in a factory is preferable in terms of quality control and reduction of construction period, there exist, even in the precast structure, some parts that need to be cast in-place such as the joints between precast segments. In the cast-in-place UHPC, however, it is probable that an optimum curing condition can hardly be realized in contrast to the factory production. In this study, therefore, the trend of compressive strength development of UHPC was experimentally investigated by assuming various inferior curing conditions that may be anticipated at a construction site. Concrete specimens were fabricated and cured under different conditions with the variables such as curing temperature, delay time before the initiation of curing, duration of curing time and moisture condition. The strengths were compared with those of the specimens cured by standard high temperature steam. Through the analysis of the test results, some minimum requirements for curing have been proposed that are required when the UHPC is cast in-place. It is expected, through this study, that practical use of UHPC in construction sites can be increased.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.2
• /
• pp.37-45
• /
• 2008

In this study, reliabilities of Cu (60 um)/SnAg (20 um) double-bump flip chip assemblies were investigated for the flip chip interconnections on organic substrates with 100 um pitch. After multiple reflows at $250^{\circ}C\;and\;280^{\circ}C$, bump contact resistances were almost same regardless of number of reflows and reflow temperature. In the high temperature storage test, there was no bump contact resistance change at $125^{\circ}C$ up to 2000 hours. However, bump contact resistances slightly increased at $150^{\circ}C$ due to Kirkendall voids formation. In the electromigration test, Cu/SnAg double-bump flip chip assemblies showed no electromigration until about 600 hours due to reduced local current density. Finally, in the thermal cycling test, thermal cycling failure mainly occurred at Si chip/Cu column interface which was found out the highest stress concentration site in the finite element analysis. As a result, Al pad was displaced out under thermal cycling. This failure mode was caused by normal compressive strain acting Cu column bumps along perpendicular direction of a Si chip.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.48 no.4
• /
• pp.98-106
• /
• 2011

Since prediction processes such as motion estimation motion compensation are not at the WZ video encoder but at its decoder, WZ video compression cannot have better performance than that of conventional video encoder. In order to implement the prediction process with low complexity at the encoder, WZ residual coding was proposed. Instead of original WZ frames, WZ residual coding encodes the residual signal between key frames and WZ frames. Although the proposed WZ residual coding has good performance in pixel domain, it does not have any improvements in transform domain compared to transform domain WZ coding. The WZ residual coding in transform domain is difficult to have better performance, because pre-defined quantization matrices in WZ coding are not compatible with WZ residual coding. In this paper, we propose a new quantization method modifying quantization matrix and quantization step size adaptively for transform domain WZ residual coding. Experimental result shows 22% gain in BDBR and 1.2dB gain in BDPSNR.

• Applied Chemistry for Engineering
• /
• v.28 no.6
• /
• pp.632-637
• /
• 2017

The vehicle lubricant occupies upto 35% in a total lubricant market and engine oil occupies upto 77% in the vehicle lubricant market in Korea. A suitable quality management of the circulating engine oil is necessary for driver and engine protection. But, KS and synthetic engine oil products (involved over 30% synthetic oil) are exempt to any quality management under Petroleum and Alternative Fuel Business Act. It is also known that synthetic oils such as PAO (poly alpha olefin) have excellent properties and performance like anti-wear, varnish control and oxidation stability than those of mineral oils. For this reason, PAO has been used for an engine oil, rotary screw and reciprocating compressor in addition to heavy duty and other extreme service applications. In this study, our research group analyzed the chromatogram pattern for the mineral oil, PAO and mineral oil involved a typical ratio of PAO using SIMDIST (simulated distillation). In the SIMDIST chromatogram, the mineral oil showed a broad peak, while PAO showed a sharp typical peak. Also the oil with a large viscosity grade exhibited a long retention time due to the heavy molecular weight and high boiling point. In particular, the blended mineral oil with 20% PAO sample showed a distinctly different pattern compared to that of using the conventional mineral oil. For monitoring PAO contents in distributing engine oils, we analyzed the SIMDIST for 27 kinds of engine oils which were popularly sold in Korea. The analytic results indicate that all kinds of engine oils showed that PAO contents were below 20% in engine oil products. Moreover, the PAO titled product was found to have a small amount of PAO. Thus, we conclude that the related laws for the proper quality management of synthetic oils are needed to be established.