• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.1011-1015
• /
• 2000

In this paper, the case studies of reducing rotational errors is theoretically done for a grinding spindle with an active magnetic bearing system. The rotational errors acting on the magnetic bearing spindle are due to mass unbalance of rotor, runout, grinding excitation and unmodeled nonlinear dynamics of electromagnets. The adaptive feedforward method based on LMS algorithm is discussed to compensate output and input disturbances, and investigated its effectiveness by numerical simulation. The feedforward control reduced external excitation and rotational error for specified frequency. The interpolation method using impulse function for cancelling the electrical 'uncut is studied. These methods show their effectiveness for the rotational accuracy of the improving magnetic bearing spindle through some simulation results of the rotational error decreased by them.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.579-585
• /
• 2003

This paper investigates the whirling, tilting and flying motion of a HDD spindle system supported by FDB experimentally. Experimental setup is built to measure the flying, whirling and tilting motion of the HDD spindle system, and three capacitance probes fixed on the xyz-micrometers measure the displacement of a HDD spindle system in the xyz-directions. This research shows that the tilting and whirling motion is mostly dependent on the centrifugal force and the gyroscopic moment due to the unbalanced mass of a HDD spindle. It also shows that the rotating HDD spindle starts to float to the equilibrium position in the z-direction until the weight of the rotating spindle is equal to the supporting pressure generated in the upper and lower thrust bearing.

• Journal of KSNVE
• /
• v.10 no.6
• /
• pp.977-984
• /
• 2000

Vibration of disk drive spindle is one of the major limiting factors in achieving higher track densities in hard disk drives. Vibration of a BLDC motor is a coupled phenomenon between mechanical characteristics and magnetic origins through the motor air-gap. In this paper, radial magnetic forces for symmetric and asymmetric BLDC motor are calculated with respect to the various rotor eccentricity using analytic method. Based on the results of the radial magnetic forces, transient whirl responses of the spindle motor are analyzed using finite element and transfer matrices. Results show that an asymmetric motor has a worse effects on unbalanced magnetic forces and vibration when mechanical and magnetic coupling exists.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2021.11a
• /
• pp.753-755
• /
• 2021

본 논문에서 기존의 치아가공기는 회전하는 모터를 사용하여 구성하였으나 이러한 모터는 정밀도, 반복정밀도가 50um 이하로 가공물 가공시에 치기공사나 치과의사가 사람에 맞추어 다시 작업을 해야하는 불편함과 시간적, 작업자의 피로도를 높일수 있는데 이러한 모터에 스크류나 밸트를 연결하여 선형적으로 움직일 수 있는 리니어모듈과 리니어모터를 적용하게되면 20um수준의 고정밀의 위치제어가 가능한 5축 치아가공기를 만들 수 있었다. 또한 MEMS센서를 이용하여 스핀들의 상태를 모니터링 하고 임계값을 지정하여 이상 신호 발생시 모터를 멈추어 위험상황에 대해서 인공지능기법을 이용하여 정지하거나 관리자에게 알림을 주어 효과적으로 5축치아가공기를 운영할 수 있도록 하였다.

• The KIPS Transactions:PartC
• /
• v.16C no.4
• /
• pp.417-422
• /
• 2009

Implementation of DPI(Deep Packet Inspection) system on a general purpose multiprocessor platform is an attractive option from the implementation cost point of view, since it does not require high-cost customized hardware. Load balancing has been considered as a primary means to achieve high performance in multi processor systems. We claim, however, that in case of DPI system design simply balancing the load of each processor does not necessarily yield the highest system performance. Instead, we propose a method in which tasks are allocated to processors based on their functions. We implemented the proposed method in dual processor Linux system and compare its performance with the existing load balancing methods. Under the proposed method, one processor is dedicated to deal with interrupt handling and generic packet processing, while another processor is dedicated to DPI processing. According to experimental results, the proposed scheme outperforms the existing schemes by 60%, mainly because of the reduction of cache miss and spin lock occurrences.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.4
• /
• pp.2350-2355
• /
• 2015

A tool was developed in this research for automation of one-dimensional finite element analysis (1D FEA) for design of a machine tool spindle system composed mainly of a shaft and bearings. As it is based on object-oriented programing, it uses the objects of a CAD system. It requires minimum data to be input to define the spindle system such as shaft cross-sections and bearing stiffness. Then, it automatically generates the geometric model based on the data and then, converts it into the FE model of 1D beams and springs. The graphic user interfaces developed allow a user to interact with the tool. This tool can be applied to identification of a near optimal design of the spindle system in minimum time and efforts by automating the FEA process with numerous design changes.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.1
• /
• pp.33-43
• /
• 1998

High cutting speeds and feeds are essential requirements of a machine tool structure to accomplish its basic function which is to produce a workpiece of the required geometric form with an acceptable surface finish at as high a rate of production as is economically possible. Since the bearings in high speed spindle units are the main heat source of the total cutting system, in this work, the thermal characteristics of the spindle bearing system with a tilting axis were investigated using finite element methods to improve the performance of the spindle bearing system. Based on the theoretical results, a specially designed prototype spindle bearing system has been manufactured. Using the manufactured spindle bearing system, the thermal characteristics were measured. From the comparison of the experimental results with the theoretical ones, it was found that the finite element method predicted well the thermal characteristics of the spindle bearing system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.407-413
• /
• 2008

This paper investigates the dynamics of a HDD spindle system due to the change of FDBs. Flying height of the HDD spindle system is determined through the static analysis of the FDBs, and the stiffness and damping coefficients are calculated through the dynamic analysis of the FDBs. Free vibration characteristics and shock response of the HDD spindle system are analyzed by using the finite element method and the mode superposition method. Experimental modal test is also performed to verify the accuracy of the proposed method. This research shows that the stiffness coefficients of journal heating mostly affect the rocking frequencies because their magnitude are within the range of the stiffness of supporting structure. It also shows that the damping coefficients of thrust bearing mostly affect the axial frequency because the stiffness of thrust bearing is much smaller that that of supporting structure.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.840-846
• /
• 2007

This paper investigates the dynamic behavior of a HDD spindle system due to the imperfect roundness of a rotating shaft. The shaft of a spindle motor rotates with eccentricity by the unbalanced mass of the rotating part. The eccentricity generates the run-out of a spindle motor which results in the eccentric motion of a rotating part. Roundness of a shaft affects this motion which limits the memory capacity of a HDD. This research proposes a modified Reynolds equation for the coupled journal and thrust FDBs to include the variable film thickness due to the roundness. Finite element method is used to solve the Reynolds equation for the pressure distribution. Reaction forces and friction torque are obtained by integrating the pressure and shear stress, respectively. The dynamic behavior is determined by solving the equations of a motion of a HDD spindle system in six degrees of freedom with the Runge-Kutta method to characterize the motion of a rotating part. This research shows that the roundness of a rotating shaft causes the excitation frequency with integer multiple of a rotating frequency.

• Tribology and Lubricants
• /
• v.15 no.3
• /
• pp.257-264
• /
• 1999

Recently as electronics and semi-conductor industry develop, ultra-precision machine tools that use air-spindle with externally pressurized air bearing appear in need of ultra-precision products which demand high precision property. Effects of air compressibility absorbs the vibration of shaft, this is called averaging effect, however, the higher running accuracy is demanded by degrees, the more important factor is machining errors that affect running accuracy of shaft. Actually, it would be very important in the view points of running accuracy to understand effects of machining errors on the running accuracy of the spindle system quantitatively to design and manufacture precision spindle system in the aspect that efficiency in manufacturing spindle system and performance in operation. So fu, there are some researches on the effects that machining error affect running accuracy. However, because these researches deal with one bearing of spindle system, these results aren't enough to explain how much machining errors affect running accuracy in the typical spindle system overall. In this study, we investigate the effects of the perpendicularity error of bearing and shaft on running accuracy of spindle system that consists of journal and thrust bearing theoretically, and suggest design guideline about shape tolerances.