• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.564-567
• /
• 2012

Optical fibers are going to be used for telecommunication, image fibers, sensors under irradiation in nuclear power plants and various irradiation facilities. Especially, Temperature detection sensors using Raman light scattering, temperature or strain sensors using fiber gratings, magnet-optical sensors using photo-magnetic effect, are already commercialized. However, When fibers are exposed to ionizing radiation, color centers are formed in fibers which reduces their light transmission, and it is limited in applying under radiation environments. In this study, $Co^{60}$ gamma-ray induced optical attenuation on Ge-doped single mode(SM) fiber has been measured. Gamma-ray is irradiated for 4hours at the dose rate of 0.5kGy/hr, 2kGy/hr, 8kGy/hr. Consequently, gamma-ray induced loss based on radiation effects in Ge-doped SM fiber occur precisely. Furthermore, dose rate effect that the higher dose rate in the same total dose, the more increase loss of optical fiber and annealing effect that the higher the loss after irradiation, the more increase the recovery rate of the loss are observed in the fiber. This results plan to make use of bases in the study of the radiation-hardened optical fiber.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.3 no.1
• /
• pp.8-15
• /
• 2012

The initial clamping forces of high strength bolts depending on different faying surface conditions drop within 1,000 hours regardless of loading, any other external force or loosening of the nut. This study is focused on an expectation model for relaxation of high strength bolt, which is confined to creep on coated faying surfaces after initial clamping. The range of this experiment is limited to estimate the relaxation of bolted joints coated by inorganic zinc primer. The candidate bolts were dacro-coated tension control bolts. The parameters of coated thickness for the faying surface were 96, 168,and $226{\mu}m$ respectively. From experiments, it exhibited that the logarithmic function for creep strain was derived due to the parameter of coating thickness. By using the creep strain, subsequently the quantitative model for estimating long term relaxation of high strength bolt can be taken with the elapsed time. The experimental results showed that the relaxation after the initial clamping of high strength bolt rose to a much higher range from 10% to 18% due to creep of the coating as the coating thickness was increased. This study showed that the clamping force reflecting relaxation after the elapse of constant time can be calculated from the initial clamping force of high strength bolt.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.202-202
• /
• 2012

유연성 투명 전도막은 현대 전자산업의 발전에 있어 필수적인 부품소재로서, 가시광선의 투과율이 80% 이상이고 면저항이 $100{\Omega}/sq.$ 전후이며 휘거나 접히고 나아가 두루마리의 형태로도 응용이 가능한 소재를 일컫는다. 이러한 유연성 투명 전도막은 차세대 정보디스플레이 산업 및 유비쿼터스 사회의 중심이 되는 유연성 디스플레이, 터치패널, 발광다이오드, 태양전지 등 매우 다양한 분야에 응용이 기대된다. 이러한 이유로 고 신뢰성 유연성 투명 전도막 개발기술은 차세대 산업에 있어서의 핵심기술로 인식되고 있다. 현재로서는 인듐 주석 산화물(indium tin oxide; ITO) 및 전도성 유기고분자를 사용하여 투명 전도막을 제조하고 있으나, ITO 박막의 경우 인듐 자원의 고갈로 인한 가격상승 및 기판과의 낮은 접착력, 열팽창계수의 차이로 인한 공정상의 문제, 산화물 특유의 취성으로 인한 유연소자로서의 내구성 저하 등의 문제가 제기되고 있다. 전도성 유기고분자의 경우는 낮은 전기전도도와 기계적강도, 유기용매 처리 등의 문제점이 지적되고 있다. 따라서 높은 전기전도도와 투광도 뿐만 아니라 유연성을 지니는 재료의 개발이 요구되고 있는 실정이다. 최근 이러한 재료로서 그래핀(graphene)과 탄소나노튜브(carbon nanotube; CNT)를 중심으로 하는 탄소나노재료가 주목받고 있으며 많은 연구가 활발히 진행되고 있다. 본 연구에서는 열화학기상증착법(thermal vapor deposition; TCVD)으로 합성된 그래핀 및 CNT를 이용하여 탄소나노재료 복합체 기반의 유연성 투명 전도막을 제작하고 그 특성을 평가하였다. 그래핀과 CNT합성을 위한 기판으로는 각각 300 nm 두께의 니켈과 1 nm 철이 증착된 실리콘 웨이퍼를 이용하였으며, 원료가스로는 메탄(CH4)과 아세틸렌(C2H2)등의 탄화수소가스를 이용하였다. 그래핀의 경우 원료가스의 유량, 합성온도, 냉각속도를 변경하여 대면적으로 두께균일도가 높은 그래핀을 합성하였으며, CNT의 경우 합성시간을 변수로 길이 제어합성을 도모하였다. 합성된 그래핀은 식각공정을, CNT는 스프레이 증착공정을 통해 고분자 기판(polyethylene terephthalate; PET) 위에 순차적으로 전사 및 증착하여 탄소나노재료 복합체 기반의 유연성 투명 전도막을 제작하였다. 제작된 탄소나노재료 복합체 기반의 유연성 투명 전도막은 물리적 과부하를 받았을 때 발생할 수 있는 유연성 투명 전도막의 구조적결함에 기인하는 전도성 저하를 보상하는 특징이 있어, 그래핀과 탄소나노튜브 각각으로 제조된 유연성 투명 전도막보다 물리적인 하중이 반복적으로 인가되었을 때 내구성이 향상되는 효과가 있다. 40% 스트레인을 반복적으로 인가하였을 때 그래핀 투명 전도막은 20 사이클 이후에 면저항이 $1-2{\Omega}/sq.$에서 $15{\Omega}/sq.$ 이상으로 급증한 반면 그래핀-CNT 복합체 투명 전도막은 30사이클까지 $1-2{\Omega}/sq.$ 정도의 면저항을 유지하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.4C
• /
• pp.163-174
• /
• 2009

Mechanical device using the load cell or strain gage sensor can be influenced by tempearute changes because temperature change can cause a shift in the load cell or straing gage output at zero loading. In this paper, micro cone penetrometers with 1~7mm in diameter, are developed by using an optical fiber sensor (FBG: Fiber Bragg Grating) to compensate the continous temperature change during cone penetration test. Note the temperature compensated method using optical fiber sensor which has hair-size in diameter, and is not affected by environmental conditions because the measured data is the wavelength shifting of the light instead of the intensity of the electric voltage. Temperature effect test shows that the output voltage of strain gage changes and increases with an increase in the temperature. A developed FBG cone penetrometer, however, achieves excellent temperature compensation during penetration, and produces continuous change of underground temperature. In addition, the temperature compensated FBG cone shows the excellent sensitivity and detects the interface of the layered soils with higher resolution. This study demonstrates that the fiber optic sensor renders the possibility of the ultra small size cone and the new fiber optic cone may produce more reliable temperature compensated tip resistance.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.20 no.1
• /
• pp.49-59
• /
• 1984

Optimizing investigation of characteristics of underwater welding by a gravity type arc welding process was experimentally carried out by using six types of domestic coated welding electrodes for welding of domestic marine structural steel plates (KR Grade A-1, SWS41A, SWS41B,) in order to develop the underwater welding techniques in practical use. Main results obtained are summarized as follows: 1. The absorption speed of the coating of domestic coated lime titania type welding-electrode became constant at about 60 minutes in water and it was about 0.18%/min during initial 8 minutes of absorption time. 2. Thus, the immediate welding electrode could be used in underwater welding for such a short time in comparison with the joint strength of in-atmosphere-and on-water-welding by dry-, wet-or immediate-welding-electrode. 3. By bead appearance and X-ray inspection, ilmenite, limetitania and high titanium oxide types of electrodes were found better for underwater-welding of 10 mm KR Grade A-1 steel plates, while proper welding angle, current and electrode diameter were 6$0^{\circ}C$, above 160A and 4mm respectively under 28cm/min of welding speed. 4. The weld metal tensile strength or proof stress of underwater-welded-joints has a quadratic relationship with the heat input, and the optimal heat input zone is about 13 to 15KJ/cm for 10mm SWS41A steel plates, resulting from consideration upon both joint efficiency of above-100% and recovery of impact strength and strain. Meanwhile, the optimal heat input zone resulting from tension-tension fatigue limit above the base metal's of SWS41A plates is 16 to 19KJ/cm. Reliability of all the empirical equations reveals 95% confidence level. 6. The microstructure of the underwater welds of SES41A welded in such a zone has no weld defects such as hydrogen brittleness with supreme high hardness, since the HAZ-bond boundary area adjacent to both surface and base metal has only Hv400 max with the microstructure of fine martensite, bainite, pearlite and small amount of ferrite.