• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1991.10a
• /
• pp.69-74
• /
• 1991

본 논문은 슬라이딩 모드 제어 기법을 이용한 직류 전동기의 디지탈 속도 제어기에 관한 연구이다. 또한 연속 시스템에 적용하던 슬라이딩 모드 제어기법을 이산 시스템에 사용할 수 있도록 해석하고, 실험하였다. 슬라이딩 모드 제어기에서 발생되는 채터링(CHATTERING) 현상을 감소시키기 위해 스위칭 주파수를 높이고, 샘플링 주기를 최대한 줄였으며 제어기 출력에 필터를 도입하였다. 또한, 스위칭 지연과 외란에 대한 보상도 고려하였으며 슬라이딩 모드 제어기를 마이크로 프로세서로 구성하였다. 전력 소비를 줄이기 위해 LIMITED UNIPOLAR 모드에서 직류 전동기를 구동하였다.

• Journal of the Korean Vacuum Society
• /
• v.13 no.1
• /
• pp.14-21
• /
• 2004

It is essential to increase the switching speed of power devices to reduce the energy loss because high frequency is commonly used in power device operation these days. In this work electron irradiation has been conducted to reduce the lifetime of minority carriers and thereby to increase the switching speed of a$p^+- n^-$ junction diode. Effects of electron irradiation on the electrical properties of the diode are reported The switching speed is effectively increased. Also the junction leakages and the forward voltage drop which are anticipated to increase are found to be negligible in the $p^+- n^-$ junction diodes irradiated with the optimum energy and dose. The analysis results of DLTS and C-V profiling indicate that the defects induced by electron irradiation in the silicon substrate are donor-like ones which have the energy levels of 0.284 eV and 0.483 eV. Considering all the experimental results in this study, it might be concluded that electron irradiation is a very useful technique in improving the switching speed and thereby reducing the energy loss of $p^+- n^-$ junction diode power devices.

• Journal of the Korean Institute of Navigation
• /
• v.21 no.3
• /
• pp.75-81
• /
• 1997

The switching components to control the speed of dc motor, which perform vital fuction in a modern motor vehicle or a ship, are susceptibile to suffer damage or upset by switching transient. An equivalent circuit was derived, in this paper, to select an ideal component having immunity against the switching transient among varisotor, zenner diode, etc. Furthermore, we have carried out the optimal improved transient protection circuit design in the view of cost effectiveness, proper wave form of transient defined by the international regulations. The process and cause of the damages in the switching components were examined. Then, the immunity improvement of semiconductor switching components to control a dc motor has been achieved considering impedance condition accoring to the variation of the diverting transient current.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.3
• /
• pp.252-258
• /
• 2010

If the speed measurement of resolver and the generation of PWM signals are implemented with single microcontroller, it is easy to reduce the system cost and to avoid the switching noise of inverters. To avoid the switching noise and to improve the accuracy of measurement, PWM switching and A/D sampling of the resolver should be synchronized. Phase angle of the resolver excitation signal is increased in stepwise manner, then, the output signal of the resolver is measured in each step. From the measured data, the optimal phase angle of resolver excitation signal is estimated using the least square approximation method.

• Journal of Digital Contents Society
• /
• v.18 no.6
• /
• pp.1193-1198
• /
• 2017

The IGBT structure developed in this paper is used as a high power switch semiconductor for DC transmission and distribution and it is expected that it will be used as an important electronic device for new and long distance DC transmission in the future by securing fast switching speed and improved breakdown voltage characteristic. As a new type of next generation power semiconductors, it is designed to improve the switching speed while at the same time improving the breakdown voltage characteristics, reducing power loss characteristics, and achieving high current density advantages at the same time. These improved properties were obtained by further introducing SiO2 into the N-drift region of the Planar IGBT and were compared and analyzed using the Sentaurus TCAD simulation tool.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.639-650
• /
• 1999

In this paper, a chattering alleviation VSS controller for the sinusoidal type BLDC motor is designed. Dead Zone function is proposed to change the chattering occurring in the transient state from high frequency to low frequency and time-varying gains are applied for the control input to eliminate the steady state excessive chattering in the conventional ISM. The proposed Dead Zone function represents the sliding layer composed of two switching surfaces and if a state vector exists in this layer, the chattering don't occur. Simulation and experimental results confirm the useful effects of the above algorithm.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.2
• /
• pp.142-148
• /
• 2006

In this paper, authors propose a novel step-up AC-DC converter operated with power factor correction (PFC) and with high efficiency. The proposed converter behaves with discontinuous current control (DCC) of input current. The input current waveform in the proposed converter is got to be a discontinuous sinusoid form in proportion to magnitude of at input voltage under the constant duty cycle switching. Therefore, the input power factor is nearly unity and the control method is simple. In the general DCC converters, the switching devices are turned-on with the zero current switching (ZCS). But turn-off of the switching devices is done at the maximum current. To achieve a soft switching at turn-off, the proposed converter uses a new partial resonant circuit, which results in the very low switching loss and the high efficiency of converter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.5 no.4
• /
• pp.309-317
• /
• 2000

This paper presents the switching angle and voltage to maximize torque/efficiency and minimize torque ripple in the 4-phase 6-poles Switched Reluctance Motor(SRM). SRM drive has high saturation and nonlinear characteristics of inductance. So we cannot hard to find optimal condition by using analytic method. Therefore it is hard to find the operating the switching angle and voltage through the approximated analysis and computer simulation by using SIMULINK according to the speed and torque required by load. From the results, we can say that the optimum average voltage is determined by the load only and the speed is determined by the optimum turn-on/off angle only. And the maximum efficiency and minimum torque ripple depend on switching angle, not on voltage. And then one-chip microcontroller controls the switching angle and voltage of an asymmetrical inverter in the SRM driver. This drive method, which is expect that the driving methods, which are maximizing torque/efficiency and minimizing torque ripple, will be suitable for the electric vehicle, the industrial application and household appliances.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.1
• /
• pp.94-101
• /
• 1999

In this paper the problems associated with the switching surge of PWM inverter devices were analysed. As the application of ASD for efficient speed control of AC rmtors is increased, so is the rrntor and ASD-related failure increased. In the industrial rmtor awlications, the introduction of PWM drives can sometmes cause insulation breakdown between the phase windings due to high transient voltage peak. The motor cable length combined with the high switching frequency becomes more sensitive issue for proper drive operation. Effects of the cable length and high switching frequency influence both on rmtor and inverter. When the insulation level of rmtor winding is low, the failure probability caused by high peak voltage and fast voltage rise times(dv/dt) is high. Voltage refloctions are simulated far rmtor capacities, ASD and rise times and are presented graphically. The filtering techniques are discussed to reduce the rmtor terminal overvoltage and dv/dt in inverter fed AC rrntor drive systems. We confirmed that the lower motar capacity and rmtar insulation level, the shorter switching time and cable length and the higrer the probability of insulation breakdown .kdown .

• Proceedings of the Korean Information Science Society Conference
• /
• 2000.04a
• /
• pp.445-447
• /
• 2000

인터넷이 급속도로 발전되면서 트래픽이 폭발적으로 증가하여 현재 라우터에 많은 부담을 주고 있다. 반면 스위칭 기술은 라우팅보다 빠르게 데이터를 전송할 수 있다. 그 결과 라우터 병목 현상을 해결하고자 IP 라우팅에 스위칭 기술을 접목한 레이블 스위칭 네트웍이 출현하게 되었다. 레이블 스위칭 기술 중 데이터 기반 레이블 스위칭에서 매우 중요한 것은 캐쉬 테이블 관리이다. 캐쉬 테이블에는 흐름 분류를 위한 정보와 레이블 스위칭을 위한 정보를 저장하고 있는데 캐쉬테이블 크기는 라우터 자원에 의해 제약을 받으므로 캐쉬 대체 기법이 필요하게 된다. 따라서 효율적인 캐쉬 테이블 관리를 위해 인터넷 트래픽 특성을 고려한 캐쉬 대체 기법에 관한 연구가 필요하다. 본 논문에서는 인터넷 트래픽 특성을 고려해 기본적인 FIFO, LFC, LRU 기법을 실제 인터넷 트래픽을 사용해 성능 평가하고 새로운 가중치 우선순위 LRU 기법을 제안한다. 특히 가중치 우선순위 LRU 기법은 플로우 인앤아웃 현상이 없고 시간이 지나도 새로운 플로우를 적절히 생성해내는 일관성을 지니면서도 스위칭 비용을 줄이는 장점을 가지고 있다.