• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.5
• /
• pp.442-446
• /
• 2004

Computer simulation of a swaging manufacturing process is presented in this paper. Commercially available software has been used to develop the simulation algorithm. Based on the experience gained from trial runs, simulation of a tube swaging process has been carried out. The material parameters "n" (strain hardening exponent) and "K" (plastic modulus) are obtained from actual tensile test measurements of the tube material. Two different geometries for the die and the tube have been used in this work and a comparison made. Numerical simulation of the swaging process has been performed using the commercially available HyperMesh(r) for pre-processing, LS-DYNA(r) for analysis and LS-TAURUS(r) for post-processing. Some of the results obtained from this study are compared with those available in the literature.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.6
• /
• pp.747-754
• /
• 2004

The nonlinear finite element analysis for deformation characteristics of a power steering hose during the swaging process is performed in order to investigate the stress and the strain levels of the hose components. Power steering hose consists of components such as rubber hose, nylon, nipple and sleeve. Moreover, the numerical analysis requires the consideration of material, geometry and boundary nonlinearities. To evaluate the rubber hose strength, the measured stresses and strains are compared with tension and compression test data. Contact force is also a principal factor to examine whether rubber hose is break away from sleeve and nipple or not.

• Journal of Power System Engineering
• /
• v.14 no.6
• /
• pp.54-60
• /
• 2010

The automotive air conditioning hose is used for connecting the components of air conditioner in a vehicle. The hose is usually manufactured by the swaging process to connect the rubber hose with the metal fitting at the end of the hose. The swaging process leads to various stress and strain configurations in the hose, which give a critical effect on the hose performance. In this paper, the deformation characteristics of an air-conditioning hose during the swaging process were analyzed using the nonlinear finite element method. Especially the rubber layers, which are contacted with the metal fittings, were divided with finer mesh density than the reinforcement braids to increase the solution accuracy. The material properties were obtained from experimental data, and the contact conditions were used in consideration of the real manufacturing process.

• Journal of the Korea Convergence Society
• /
• v.8 no.12
• /
• pp.275-281
• /
• 2017

The automobile cowl cross bar which is a backbone frame part inside the cockpit module has been designed with more complex geometries recently due to demands of its enhanced functions and reduced weight of car. The traditional manufacturing process using welding between tubes with different diameters shows several problems such as poor mechanical characteristics and appearance, etc. Therefore, in this study, manufacturing processes which can eliminate the welding process were developed by applying one-piece metal forming processes such as tube drawing and radial swaging. As results, it was found that the one-piece manufacturing processes give better bending strength than the traditional welding process and the swaging process shows the lowest manufacturing cost.

• Journal of Power System Engineering
• /
• v.7 no.2
• /
• pp.44-50
• /
• 2003

The power steering hose is a kind of high-pressure hose with reinforced braids in rubber material. It is usually manufactured through the swaging process. In this paper, the deformation characteristics of a power steering hose during the swaging process were analyzed using the nonlinear finite element method. The material properties were obtained on experiments, and the contact conditions were used in consideration of real manufacturing process. Investigations were focused on the stress and strain values of the hose and meta] components at the maximum jaw stroke and at the completion of the process. Especially, the results of inner rubber component were interpreted in detail, because of its important role in the hose efficiency.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.8
• /
• pp.760-766
• /
• 2009

In the manufacturing process of HDD, ball swaging method is commonly used to joint the Head Gimbal Assembly(HGA) with the arm of the actuator. The hub on the HGA is placed into the hole of the actuator arm, and the hub and arm is bonded by the pressure of steel ball. The pressure for plastic deformation on the baseplate causes the undesirable deformation on HGA, such as tilting, flying height change of head. After obtaining the key parameters that have large sensitivity on the swaging process, the optimal shape of baseplate is proposed to increase the static performance during swaging process. Contribution of the proposed design for the swaging performance is verified by contact simulation with elasto-plastic deformation.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.4
• /
• pp.37-42
• /
• 2003

The mechanical components with high-pressure hoses are generally produced by the swaging process. The hoses are composed of the rubber materials and the reinforced braids to support tensile forces. In case they are subjected to high mechanical and thermal loads under severe operating conditions, the oil in hoses can leak at the parts of small clamping forces. In this paper, the deformation characteristics of a fiber-reinforced hose are analyzed with respect to the jaw strokes using the finite element method. The manufacturing process is modeled with a contact problem in consideration of a real situation, and the material properties based on the experimental results are used in the analysis. Examinations of the relationship between the swaging strokes and the deformation behaviors of the hose were made on the basis of the stress and strain values of the hose components. The relations between clamping forces and separating forces are also proposed, in order to estimate clamping forces corresponding to separating forces for the given model.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.6
• /
• pp.106-112
• /
• 2019

Rotary swaging is a method of forging automotive drive shafts. In this paper, we propose a new two-hammer forging technique by applying the problem-solving approach TRIZ to improve the efficiency and productivity of the rotary swaging automation process. We will simplify the materials and hammers via the 3D modeling tool SolidWorks for high accuracy of a comparative analysis of existing and proposed methods under the same boundary conditions. In addition, we will compare the stress trends of the proposed model using ANSYS Workbench and verify the feasibility through a comparison of the simulation results using DEFORM. Relative to the existing method, the proposed method can decrease production costs and improve efficiency of the automation process by reducing the power source.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.127-133
• /
• 2005

Rotary swaging is one of the incremental forming process which is a chipless process using the reduction of cross-sections of bars, tubes and wires. The TDS(Tube Drive Shaft) of monobloc used in automotive has been developed by the rotary swaging process. The mechanical characteristics of swaged parts such as the hardness, thickness and roughness are also estimated to conduct experimental analyses of rotary swaging process with the materials of 34Mn5 Furthermore the change in the vibration mode of TDS due to design parameters, which are the tube length, diameter and thickness, has been investigated and analysed. The weight of the TDS product is smaller by about $12.8\%$ than that of SDS with the same performance. It could be evidently found that the TDS is designed to be much lighter than SDS (Solid Drive Shaft). This advantage might give some possibility to improve the NVH (Noise-Vibration-Harshness) characteristics. A maximum torque and a total number of torsional repetitions for the TDS is checked and measured to know the torsional intensity and fatigue strength through the static torsion test and torsional durability test, respectively. A total number of the torsional repetitions up to the fracture for the TDS is greater than 250,000 times.

• 한국가스학회:학술대회논문집
• /
• 2003.05a
• /
• pp.142-149
• /
• 2003