• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.4A
• /
• pp.232-237
• /
• 2003

We present the derivation of the loci of the reflection coefficient of a loaded transmission line on the Smith chart as the length of the transmission line is varied. The results show that the loci constitute a circle when the characteristic impedance of the transmission line differs from the normalizing one, whose center and radius are determined by the impedances of the load and the transmission line. The results can be used in the matching circuit design using microstriplines when line width and length should be compromised.

• Journal of the Microelectronics and Packaging Society
• /
• v.31 no.2
• /
• pp.28-35
• /
• 2024

Corrosion inside electronic packages significantly impacts the system performance and reliability, necessitating non-destructive diagnostic techniques for system health management. This study aims to present a non-destructive method for assessing corrosion in copper interconnects using the Smith chart, a tool that integrates the magnitude and phase of complex impedance for visualization. For the experiment, specimens simulating copper transmission lines were subjected to temperature and humidity cycles according to the MIL-STD-810G standard to induce corrosion. The corrosion level of the specimen was quantitatively assessed and labeled based on color changes in the R channel. S-parameters and Smith charts with progressing corrosion stages showed unique patterns corresponding to five levels of corrosion, confirming the effectiveness of the Smith chart as a tool for corrosion assessment. Furthermore, by employing data augmentation, 4,444 Smith charts representing various corrosion levels were obtained, and artificial intelligence models were trained to output the corrosion stages of copper interconnects based on the input Smith charts. Among image classification-specialized CNN and Transformer models, the ConvNeXt model achieved the highest diagnostic performance with an accuracy of 89.4%. When diagnosing the corrosion using the Smith chart, it is possible to perform a non-destructive evaluation using electronic signals. Additionally, by integrating and visualizing signal magnitude and phase information, it is expected to perform an intuitive and noise-robust diagnosis.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.7
• /
• pp.1015-1020
• /
• 2018

The cavity resonator is one of the widely used components in the microwave applications. The unloaded Q, the resonant frequency, and the coupling factor are basic parameters of a cavity. A simple unloaded Q factor measurement procedure of a cavity is proposed in a lossy coupling. The equivalent circuit of a cavity with coupling loss at near the resonant frequency is presented. The coupling loss resistance was found by the measurement of a cavity impedance. The cavity impedance compensated coupling loss was redrawn on the Smith Chart. The loaded Q and coupling factor were obtained based on the compensated impedance locus and then the unloaded Q factor was calculated. To verify the proposed procedure, the cavity with lossless coupling was measured. The two measurement results in the lossy and lossless coupling agree well. The results confirm the proposed procedure is valid.

• Proceedings of the KAIS Fall Conference
• /
• 2003.06a
• /
• pp.247-249
• /
• 2003

본 연구에서는 RF 전력을 사용하는 플라즈마 식각/증착 장비에서의 플라즈마 챔버 내의 임피던스를 정확하게 측정하기 위한 Adaptor를 개발하였다. 개발된 Adaptor는 RF Matcher와 결합되며 RS-232 통신포트를 통하여 PC와 연결하여 챔버내의 임피던스 변화를 스미스 차트로 표시하여 실시간 관측이 가능하다. 이러한 Tool을 이용하여 수집된 데이터는 최적의 공정조건 구축에 활용이 가능하며 반도체 생산 라인에서의 생산성 향상에 기여할 수 있다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.54-55
• /
• 2011

In recently, microstrip antenna has been used to be communication devices through compact size, lightweight, and multi-layered integration. Also miniaturized communication system is expected to be power consumption and cost savings. In this paper, Long-distance communication is possible for the purpose of micro-strip antenna design, and prototype antenna were made and analyzed by using network analyzer.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.12
• /
• pp.15-19
• /
• 2016

The gate bias dependence of kink phenomenon with a large deviation from the resistance circle in Smith chart is observed in the frequency response of $S_{11}$-parameter for large multi-finger RF MOSFETs. For the first time, this bias dependence is analyzed by measuring magnitude and phase of $S_{11}$-parameter, input resistance and input capacitance. As a result, $V_{gs}$ dependent $S_{11}$-parameter is largely changed by the magnitude of input capacitance as well as dominant pole and zero frequencies of input resistance. At $V_{gs}=0V$, the kink phenomenon occurs in the high frequency region because of very small phase difference of $S_{11}$-parameter and high pole frequency of input resistance. However, the kink phenomenon at higher $V_{gs}$ is generated in the low frequency region owing to large phase difference and low pole frequency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.2
• /
• pp.171-178
• /
• 1998

Generally, the output matching circuit has the most influence to the output power of oscillator and existing method for output matching has difficulty for making the optimum output matching circuit because the matching has to be done nearby the infinite impedance area of the Smith Chart. In this paper, it is studied for the output matching circuit of the microwave oscillator to get the maximum output power. The maximum output point can be found by adjusting the position of moving short in the Tuner while the oscillator is operating after connect the 3-dB coupler Tuner to the oscillator without output matching circuit. To design the oscillator for the maximum output power can be done easily with the microstrip line which is realized from the measured S-parameters of Tuner. In compare the oscillator by the existing method with another one by the suggested method in this paper, the first one has 6.45 dBm output power and second one has 9.71 dBm which is 3.26 dBm higher than the first one at the oscillation frequency 1.0338 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.6 s.109
• /
• pp.511-518
• /
• 2006

In this paper, a small RFID tag antenna in UHF band which has bandwidth-enhanced characteristic is proposed. The shape of the proposed antenna is a meander antenna to have size-reduced characteristic, and it consists of two radiators which make dual resonance in adjacent frequency to enhance bandwidth. By adjusting length and location of each radiator, the proposed antenna can make dual resonance at arbitrary location on the Smith chart, which is able to make impedance matching with RFID tag chip in wide frequency range. And it is apparent that the proposed antenna can have bandwidth-enhanced characteristic according to the simulated and measured results.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.1
• /
• pp.193-198
• /
• 2009

In this paper, we report the design of UHF RFID ceramic antenna using HFSS, one of the widely used RFID design tools. Of the developed antenna system, we analyze its Return Loss using HFSS and its characteristics using Smith Chart methodology. We built the ceramic antenna system based on the HFSS design, and analyzed its performance by measuring the impedence matching and gains using Network Analyzer. We attach the developed prototype to UHF RFID portable terminal, and performed distance measuring for five widely used types of RFID tags to verify the performance of our proposed antenna system.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.5
• /
• pp.10-17
• /
• 1989

A new design method of lossy matching network for the microwave broadband ampilfier is presented by using seattering parameters instead od modeling of transistor. A lossy matching network is represented as the combination of 2 lossless networks between which lossy serial or parallel immittance is inserted without using specific topology, and so many useful matching cireuits can be realized. Also it is shown that linear transforming relation exists between gain and reflection coefficient of the amplifier, and the transforming equation is derived using scattering parameters. With this equation some constant gain circles can be drawn on reflection coefficient plane to get adequate reflection coefficient and gain. And since the relations between amplifier gain/reflection coefficient and the immittance of passive element are bilinear transformations. constant gain or reflection coefficients circles. Illustrative examples are presented to show the usefulness of proposed method.