• Journal of the Earthquake Engineering Society of Korea
• /
• v.4 no.2
• /
• pp.65-72
• /
• 2000

콘크리트 구조물이 지진 등으로 손상을 입었을 때 그 내부 상태를 파악하는 일은 구조물의 안전성 판단에 필요한 중요 과정중 하나이다 손상도 파악에 사용되는 비파괴 검사 방법 중 레이더법은 현재 콘크리트 부재의 두께와 매립된 철근 및 공동 탐사에 적용되고 있다 레이더법은 다른 비파괴 검사 방법에서와 마찬가지로 측정된 신호의 처리와 해석에 따라 그 결과가 좌우된다 . 이논문에서는 상용 레이더 시스템에서 얻어지는 화상 데이트터를 개선하는 방법을 개발하여 철근이 매립된 콘크리트 시편에 적용하였다 실험에 사용된 기편의 크기는 1,000mm(길이)$\times$600mm (폭) $\times$140mm(두께) 이고 철근의 매립깊이는 표면으로부터 철근 중심까지 60mm 이다 레이더 실측 실험에서 철근의 수평배근 간격을 60 90, 120, 150 mm 로 변화시켜 간격탐사가능성을 시험하였다 결과적으로 상용 시스템에 비해 샹상된 판별효과를 나타냈으며 배근 간격이 90, 120, 150mm 인 시편에서 그 간격을 정확히 찾아내었다.

• 발명특허
• /
• v.27 no.5 s.311
• /
• pp.68-74
• /
• 2002

본 발명은 키토산으로 이루어진 무수히 많은 갯수의 박막필름이 시트 평면에 수직, 수평 또는 경사 방향으로 일정간격의 공간을 유지하면서 적충되어서 라멜라구조를 형성하고 이 박막필름들이 일정한 간격으로 가지런히 나열되어 형성된 키토산 마이크로 플레이크로 이루어진 층상 격막시트에 관한 것이다. 두께 $1\mu{m}$내지 $50\mu{m}$로 라멜라구조를 이루는 키토산 박막필름이 $1\mu{m}$내지 $10000\mu{m}$의 공기간격을 두고 누적층을 형성하고 시트평면과$0^{\circ}C$내지$180^{\circ}C$사이의 일정 각도로 균일하게 배열되어 있어 수직, 수평 또는 경사방향으로 키토산 박막필름이 가지런히 배열되어 있는 키토산으로 조성된 수용성 층상 격막시트에 관한 것이다. 본 발명은 키토산을 약산성 액상에서 용해, 숙성 시켜 추출 고화 시키는 과정에서 수직, 수평 및 경사방향으로 키토산 마이크로 플레이크가 층상 라멜라구조를 이루는 키토산 격막시트를 형성시켜 줌으로 임상의학적 적용시 각각의 키토산 박막필름 사이의 균일한 공간으로 다양한 약물의 적용이 가능하며 특히 액상의 약재를 적용시 모세관의 원리에 따라서 약물이 원활하게 공급되는 약전성이 매우 우수하고 약물의 포집성이 획기적으로 부과된 재료로 사용될 수 있으며 키토산을 용해시켜 이용하는 산업에서 물에 신속하고 완전한 용해특성을 나타내는 키토산 원료물질로 사용될 수 있는 것이다.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.1
• /
• pp.117-129
• /
• 2000

This paper discusses the lateral behavior of group pile in homogeneous and non- homogeneous (two layered) soil. In the group pile, the model tests were to investigate the effects on spacing-to-diameter ratio of pile, pile array, ratio of pile spacing, constraint condition of pile tip, eccentric load and ground condition. The group efficiency and lateral deflection induced in active piles were found to be highly dependent on the spacing-to-diameter ratio of pile, number of pile. Lateral bearing capacities in the group piles of fixed tip, in the case of 6D spacing and $3\times3$ array, were 40-100% higher than those in the group pile of free tip. Based on the results obtained, a spacing-to-diameter of 6.0 seems to be large enough to eliminate the group effect for the case of relative density of 61.8% and 32.8%, and then each pile in such a case behaves essentially the same as a single pile. However, in the case of dense sand, it can be estimated that a spacing-to-diameter of 8.0 seems to be large enough to eliminate the group effect. In this study the group efficiency is illustrated in experimental function with spacing-to-diameter, S/D, relative density and number of pile. The distribution of shear force in lead row piles, in the case of 3$\times$3 array group pile, was 41.6-52.4% for 3D spacing and 34-40% for 6D spacing, respectively. The shadowing effect for the parallel direction of lateral loading appears to be more significant than the one for the perpendicular direction of lateral loading.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.4
• /
• pp.23-36
• /
• 2008

This study describes model tests on instrumented rectangular-shaped passive row piles embedded in horizontal sand-ground undergoing lateral soil movement. We tried to find the property of row piles dependent on the shape of pile, including the position of the pile in row, pile spacing, and soil movement. The results of test are as follows. The lateral earth pressure diagram variously appeared to be triangle, trapezoid and rectangular by shape and position of pile. The outer pile has a larger bending moment than the inner pile in the case of B-type, the inner piles has larger one than outer pile in case of H-type. $R_f$ (the ratio of resistance to lateral soil movement) was found to increase with increasing pile spacing irrespective of pile-shape. Y/L (location of action of lateral resistance force) for $d_s$ (displacement of soil) and $S_h$ (spacing of pile) appeared to be nearly regular position, and H-type is higher than B-type.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.209-220
• /
• 2001

준설매립지반 표층강도증진을 위한 수평진공배수공법 적용시의 압밀현상 예측을 위한 연구를 수행하였다. 초연약지반에 수평배수재와 진공압을 이용하여 수평진공배수 공법을 적용할 경우, 배수재 부근에서 3차원적 배수특성과 넓은 범위의 유효응력의 변화, 지반의 압축성 및 투수성이 크게 변화하게 된다. 이를 위하여 3차원 배수특성과 다양한 경계조건, 부의 간극수압 발생을 통한 유효응력의 증가, 유효응력에 따른 압축성과 투수성의 비선형성을 포함할 수 있도록 기존의 3차원 압밀 지배방정식을 확장 유도하였고, 유효응력-간극비-투수계수의 관계를 누승형태의 함수로 표현하여 사용하였다. 해석기법의 타당성을 검증하기 위하여 실내에서 수행된 대형 토조실험 결과를 모델링하여 좋은 일치를 확인하였고, 이를 바탕으로 수평진공배수공법 적용시의 압밀효과에 대한 분석결과 드레인이 타설된 상부지반에서는 균등한 개량효과의 결과를, 하부의 미개량 지반에서는 자중압밀에 의한 압밀효과를 확인할 수 있었으며 배수재의 수평타설 간격에 따른 압밀효과 분석을 통하여 적정 배수재 설치간격의 범위를 확인하였다.

• Journal of the Korean GEO-environmental Society
• /
• v.10 no.5
• /
• pp.69-73
• /
• 2009

In this study, three dimensional numerical analyses were performed with variation of pile spacing (S=3D, 4D, 5D) to compare the behaviour of single pile and pile group with cap in granite soil. In order to compare and analyze the lateral resistance of single pile and pile group by changing pile spacing, the pile group with array of $1{\times}3$ was employed. To reduce the computation time the symmetric boundary condition was used. And Druker-Prager model and elasticity model were used for granite soil and for concrete pile and cap, respectively. Using the analyses results of pile group in granite soil under lateral loading, p-y curve for pile group and single pile with changing pile spacing was drawn. With p-y curve p-multiplier was evaluated. As a result of analysis, the value of p-multiplier was increased with increasing pile spacing under 1.0 due to pile shadow effects.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.3
• /
• pp.17-22
• /
• 2010

This paper analyzed the characteristics of p-multiplier and the load distribution of H-pile group installed in weathered soil under horizontal loading. The results of this study conducted in pile arrangement ($2{\times}3$, $3{\times}3$), the pile center to center spacing (2D, 4D, 6D), and soil density (relative density: 40%, 80%) were drawn as follows. As to the average horizontal loading applied to each pile in pile groups, the fewer number of piles was, the larger average horizontal resistance became. As the result of analysis on p-y curves of single piles and pile groups according to the pile distance and the soil density, as the pile spacing was increased from 2D to 6D, the interaction coefficients of pile group showed 0.85~0.94 (piles in the front row), 0.57~0.79 (piles in the middle row), and 0.60~0.71 (piles in the rear row) in the loose ground and showed 0.76~0.82 (piles in the front row), 0.58~0.73 (piles in the middle row), and 0.53~0.70 (piles in the rear row) in the dense ground. As above, the wider pile distance was, the larger interaction coefficient value was shown among piles. In addition, piles in the front row showed bigger interaction coefficients than that of piles in the middle and back row.

• Journal of the Korean GEO-environmental Society
• /
• v.20 no.1
• /
• pp.43-49
• /
• 2019

In this paper, we introduced phase optimization techniques in the Soil-Nail design to optimize the reinforcement required for each grade level. The optimal design results at the maximum slope height were further amplified to allow for phase optimization of the horizontal spacing of the Nail in accordance with the change in the height of the slope. The limit equilibrium analysis was performed by step-by-step sloping height, and the safety factor exceeded when the horizontal spacing of four days was fixed. The process of optimization was effectively carried out by densifying the required reinforcement depending on the slope elevation. Also limited to reflect the axial force of the nail into the reinforcement details.Using the method, the members' strength was reflected. When phase optimization technique is applied for each slope height by calculating the stiffening precision, it is judged that it will be more economical to optimize horizontal intervals by effectively reducing the repeated reinterpretation process that satisfies the reference safety ratio for each slope height.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.6
• /
• pp.193-205
• /
• 2001

In this study the behavior of pile groups is investigated experimentally. Special attention is given to the load transfer characteristics of pile groups and to the evaluation of the group effects under vertical and horizontal loadings. In the laboratory experiments, vertical and lateral loadings were imposed on model piles in sand. Model piles made of PVC embedded in Joomoonjin sand were used in this study. Pile arrangements($2\times2,\; 3\times3$) and pile spacings(2.5D, 5.OD, 7.5D) were considered. Load-transfer curves(t-z, q-z and p-y curves), load-deflection curves and group interaction factors were obtained from the experimental results. The group interaction factors under both vertical and horizontal loadings were proposed for the cases of $2\times2\; and\; 3\times3$ pile groups with varying ratios of pile spacings. p-multipliers in this study were found for the individual piles in $2\times2\; and\; 3\times3$ pile groups.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.32 no.5
• /
• pp.305-311
• /
• 2019

In this study, we examined the proper spacing between the expansion joints according to the temperature load of the inter-modal terminal platform infrastructure to implement a new inter-modal automated freight transport system, which we intend to introduce in Korea. To review the proper expansion joint spacing of the terminal platforms, we set the maximum expansion joint spacing according to the regional temperature changes using the equation proposed by the Federal Construction Council (FCC) of the United States. Then, the maximum displacement value, which was calculated through the structural analysis program, and the limit of the horizontal displacement of the building structure were compared. The proper expansion joint spacing was selected as the slab length at which the maximum displacement of the structure, due to temperature changes, was below the horizontal displacement limit. Based on the application of maximum expansion joint spacing for each region calculated through the FCC's suggestion, the maximum displacement that could occur within the limit of the lateral displacement of the structure was determined.