• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.1884-1888
• /
• 2008

한국수자원공사는 국내 수자원 관리의 문제점들을 해결하기 위한 기술을 개발하고, 유역 수자원 활용 계획 및 과학적인 다목적댐 운영방안을 마련하기 위하여, 2001년 용담댐 유역을 수자원 시험유역으로 지정하였다. 특히 최근에는 용담호의 유입지천 중 구량천의 상류에 위치한 농업용 저수지인 양악호의 상 하류 지역을 "물수지 시험유역"으로 지정하고, 집중 배치된 다양한 수문관측 장비로부터 신뢰도 높은 자료를 취득하고 있으며, 아울러 농업지역에서의 물수지 분석을 위한 연구를 진행하고 있다. 물수지 시험유역은 향후 공업지역과 주거지역 등 다양한 지역을 대상으로 확대 추진할 계획이며, 종국적으로는 물을 사용하고 있는 형태에 따른 다양한 물수지 특성을 종합하여 다목적 댐의 운영에 필요한 우리나라 고유의 물수지 자료를 구축하고자 한다. 본 논문은 물수지 시험유역 소개, 시험유역에 설치한 수문관측 장비 설명, 저수위 모니터링 결과보고 등의 내용으로 구성되었으며, 구체적으로는 저수지내 수문관측 시설에 대한 정밀측량 실시결과, 저수지의 수위별 내용적 자료, 저수지 근방의 강우자료 및 단기간동안 이루어진 저수지 내에서의 수위 변동 특성을 보여준다.

• Polymer(Korea)
• /
• v.31 no.2
• /
• pp.105-110
• /
• 2007

We investigated resin, thinner, painting, and injection for analyzing the chemical effect of polymer, and made the optimum solution with the best performance of ABS (acrylonitrile butadiene styrene) resin. The effect depended on chemical material especially its chemical and physical properties instead of mechanical transformation. When we looked over ABS resin, injection, chemical material and painting, we found out thinner was the main factor for painting problem. Throughout this test, we could solve the problem, secure the system for control process and drop many factors for changing quality.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.11a
• /
• pp.63-63
• /
• 2011

통상적으로 코팅가공시 수지의 흐름성을 개선하기 위해서 코팅수지(점도 : 50,000~60,000 Cps)의 점도를 10,000 Cps 이하로 낮추어서 작업을 진행한다. 이때 MEK(Methyl Ethyl Ketone), TOL(Toluene), DMF(Dimethyl Formamide) 등과 같은 유기용제를 사용하여 점도를 조절한다. 본 연구는 기존에 표면처리 코팅용 수지 배합시 유기용제를 사용하는 대신 물을 사용하여 점도 조절이 가능한 표면처리 코팅용 hydrophilic PU 수지를 연구하였다. Prepolymer 법으로 합성한 수지가 One-shot법으로 합성한 수지보다 water dilution 안정성이 우수하며, 친수성 polyol과 소수성 polyol의 비율이 6/4정도가 될 때 water dilution된 수지의 안전성, 투습도 등의 물성이 가장 이상적으로 발현 되는 것을 확인 할수 있었고, 50part의 물과 희석 후 5일 이후에도 상분리가 되지 않음을 확인 할 수 있었다. 개발된 수지의 적용성을 평가한 결과, J-knife를 이용하여 knife over roll 방식으로 $200{\mu}m$의 gap으로 80/120/$140^{\circ}C{\times}10m/min.$의 다단건조 공정으로 진행했을 때 최적의 물성을 얻을 수 있었다.

• Archives of Hand and Microsurgery
• /
• v.23 no.4
• /
• pp.262-266
• /
• 2018

Flexor digitorum profundus (FDP) tears in adolescents appear as avulsion tears in the FDP tendon, whereas longitudinal tears are very rare. Moreover, there has been only one reported case of intratendinous fibroma occurring in the flexor tendon of a finger. A longitudinal tear of the flexor profundus tendon associated with an intratendinous fibroma has not been previously reported. We report one case of a longitudinal partial tear accompanied by an intratendinous fibroma at the FDP tendon of the left middle finger after a hyperextension injury caused by the impact of a baseball. Given the rarity of longitudinal flexor tendon tears in adolescents, in such cases, the possibility of an underlying pathology should be considered.

• Composites Research
• /
• v.24 no.2
• /
• pp.30-37
• /
• 2011

Analysis of wettability between epoxy resin and glass fabric was studied. The mixing ratios of epoxy resin and anhydride hardener were varied as 1:0.5, l:l and l:1.2. Catalyst content was fixed as 0.1wt% of the mixed resin. A curing analysis by differential scanning calorimeter(DSC) showed a possible impregnation of the mixed resin at the room temperature. An effective contact angle of the mixed epoxy resin drop onto the glass fabric being preset on a flat glass plate was measured as a function of time. The wet area of the epoxy resin drop was also measured. Behaviors of the contact angle, the droplet height, the neat wet area and the coefficient of wettability were used to evaluate the wettability of the epoxy resin onto the glass fabric. It was concluded that the equivalent ratio of 1: 1.2 was the most suitable for the wettability.

• Journal of Korean Society of Forest Science
• /
• v.60 no.1
• /
• pp.37-44
• /
• 1983

Thermoplastic aceton-formaldehyde resin adhesive was added as a modifier for urea-formaldehyde resin adhesive and its effects on plywood smear strength and wood failure were investigated. The results are summarized as follows: 1) The plywood shear strength and wood failure showed the highest values at $120^{\circ}C$ of hot plate temperature, but the values decreased according to the rise of addition ratio of aceton resin. 2) The variation of molar ratio of aceton resin had no effect on plywood shear strength and wood failure. 3) The plywood bonded by the addition of aceton resin showed lower values than those of urea resin bonding plywoods in shear strength and wood failure. Therefore, aceton resin was inadequate as a modifier of urea resin adhesive.

• Composites Research
• /
• v.31 no.1
• /
• pp.23-29
• /
• 2018

The RFI process can be applied to very thick structures without limiting the resin viscosity. When the proper thickness of the resin film cannot be set, the resin film creates either the non-impregnated section or the excessive resin contents and this leads to the deterioration of mechanical properties. Therefore, this study proposed a method for setting the resin film thickness in the RFI process. The fiber compaction behavior test was proposed by setting the proper resin film thickness and the properties of composites were evaluated through short beam shear strength test, compression test and porosity measurement to verify the proposed method. The evaluation of physical properties of composites was conducted and an appropriate level of resin film thickness was found based on the results of fiber compaction behavior test.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.1
• /
• pp.72-78
• /
• 1999

To accelerate the curing and to improve the bonding properties of urea-melamine-formaldehyde (UMF) resin adhesives for plywood, the effects of resin compositions and additives on gelation time and bonding strength were discussed. The gelation time of UMF resin prepared by simultaneous reaction with urea(U), melamine(M) and formaldehyde(F) at M/U molar ratio 0.2 was shortened as the molar ratio of formaldehyde to urea was increased. However, at F/U molar ratios higher than 2.5, the amounts of free fomaldehyde of resin could not satisfy with KS standard, Therefore, it was difficult to increase the amount of formaldehyde in resin composition for the purpose of fast gelation time. With increasing the molar ratio of melamine to urea(M/U) from 0.3 to 0.6 at constant F/U molar ratio 3.4, the gelation time of UMF resin was slightly decreased, while gradually increased at M/U molar ratio higher than 0.6. The gelation properties of UMF resin and bonding strength of UMF-bonded plywood could be enhanced by using ammonium chloride and p-toluene sulfonic acid as a curing-agent together with wheat flour and corngluten powder as a extender.

• Journal of Adhesion and Interface
• /
• v.15 no.4
• /
• pp.145-150
• /
• 2014

Dicyclopentadiene (DCPD)-based hydrocarbon resins are widely used as tackifiers in many applications. In particular, hydrogenated DCPD-based hydrocarbon resins are widely used in premium hot-melt-type adhesives such as hot melt adhesives (HMAs) and/or hot melt pressure-sensitive adhesives (HMPSAs), because are water-white in color and possess excellent stability to light and heat. This article discusses the adhesive performance of various hydrogenated DCPD resins when they are used as tackifiers in styrene-block-copolymer (SBC)-based HMPSAs. This article shows the correlation between the characteristics of tackifiers and the adhesive performance of SBC-based HMPSAs. The higher the softening point of the tackifier, the higher is the $T_g$, softening point, and crossover temperature of the PSAs. High aromatic H wt% content reduces the high-temperature resistance of PSAs, as suggested by the decrease in the crossover temperature and softening point of the PSAs.

• Elastomers and Composites
• /
• v.44 no.4
• /
• pp.373-377
• /
• 2009

Most of the plastics products are being manufactured by injection molding. Warpage in injection molded affects the product dimension and it causes assembling problem. In this study, warpages in the injection molded part been studied. Specimens are rectangular flat shapes with and without ribs. Amorphous polymers (PC and ABS) and crystalline polymers (PP and PA66) were used for material. Flat shape with ribs showed higher warpage than flat shape without ribs by 6 to 9%. The specimens with ribs that are located parallel to the flow direction has higher warpage than specimens with ribs that are located perpendicular to the flow direction by 25 to 39%. Crystalline polymers have higher warpage than amorphous polymers by 23 to 67%. Warpage decreases as packing time increases and it increases as injection temperature increases.