• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.12
• /
• pp.279-286
• /
• 2018

The grouting method is to reinforce the ground by injecting the chemical solution for the strengthening of the ground. Cement grouting material has usually used portland cement for centuries ago, but the cement particle size is large and the injection effect is limited. This study analyzes the effect of ultrafine cement grouting in rock ground using 3S-1 grouting in rock ground and ordinary Portland cement (OPC). The results of tests were compared and analyzed from the Lugeon test, bore loading test (P.M.T.), and injection (P-Q) test. The use of ultrafine cement (3S-1) had a higher effect (K, 10-6cm/sec) than OPC. The reinforcement effect of 3S-1 was also confirmed. Ultrafine cement (3S-1) was 4~9 times more injectable than OPC. Therefore, it is more advantageous to use ultrafine cement (3S-1) than OPC.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.259-267
• /
• 2001

실내시험으로 구한 점토의 공학적 성질은 샘플링, 운반, 저장, 그리고 성형과정 동안에 발생하는 시료의 교란으로 인해 원지반의 성질과 다르게 측정된다. 본 연구에서는 양산점토에 대한 삼축압축시험($CK_{o}$ UC) 결과를 이용하여 샘플링 방법에 따른 교란의 정도를 평가하였다. 실험에 사용된 시료는 76mm 튜브샘플러, 76mm 피스톤샘플러, 블록샘플러로 채취되었으며, 시료의 교란정도를 평가하기 위해 각 시료에서 측정된 체적변형률, 비배수 전단강도, Secant Youngs modulus, 그리고 파괴시 간극수압계수를 비교하였다. 시료의 교란정도를 평가하는 것 이외에도 SHANSEP 방법을 이용하여 수행한 $CK_{o}$ U 삼축압축시험 결과를 이용하여 양산점토에 대한 정규화 전단강도($C_{u}$ /$\sigma$$_{vc}$ )와 OCR 관계를 규명하였다. 또, 피에조콘 관입시험, 딜라토메타 시험, 그리고 현장 베인시험결과를 이용하여 구한 양산점토의 비배수 전단강도를 삼축압축시험 결과와 비교하였다.

• Economic and Environmental Geology
• /
• v.13 no.3
• /
• pp.185-192
• /
• 1980

The rocks exposed in the investigation area are andesite of Late Cretaceous age, and syenite and aplitic granite of Bulgugsa Series of Early Cretaceous Period, which is intruded in the older andesitic rock. The strike and dip of major joint is $N10^{\circ}$ to $60^{\circ}E$, and $70^{\circ}SE$ to vertical respectively. According to seismic exploration, lower velocity zone, deemed to be fractured and/or crushed zone, is appeared along the gully center of east flank of the area. Test drilling shows that andesite bedrock is mostly very hard, massive, and very fine to medium grained and has almost 100 percent RQD and core recovery. In comparision with andesitic bedrock, intruded syenite cores show that it is highly crush especially at the depth from 55m to 63m.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05a
• /
• pp.617-622
• /
• 1995

다목적연구로 HANARO를 이용한 압력용기 재료 조사시험에 이용될 계장캡슐(Instrumented Capsule)의 열적, 역학적 특성분석이 수행되었다. 캡슐에 장입될 조사시편의 온도평가는 GENGTC 와 HEATING 7.2f를 이용 계산하였다. 또한 이들 온도분포로 인하여 발생하는 캡슐외통과 End Plug에서의 응력해석은 전산코드 ANSYS를 이용 수행하고, 냉각수압에 의한 캡슐본체의 좌굴응력을 계산함으로서 강도평가를 하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1997.11a
• /
• pp.30-30
• /
• 1997

국내에서는 시도되지 않았던 조립식 맨드렐 및 prepreg 제작 방식을 적용하여 filament winding machine으로 압력 용기(STEB)를 제작, 음향 방출 측정 장비 및 strain gage 등을 부착한 수압 시험으로 압력용기의 구조적 건전성 예측 및 파열 압력을 측정하여 성능을 분석하였다. 동일한 winding pattern 및 조건하에 prepreg winding과 wet winding 방식을 적용하여 제작한 압력 용기의 성능을 비교하였고, prepreg winding의 설계 조건, 공정 변화를 통해 제작한 압력 용기의 파열 압력 및 형태를 분석하였다. 이러한 winding 조건들에 따라 제작된 압력용기는 최종적으로 PR(Performance ratio) 값을 산출하고, 이를 통하여 prepreg 제작 방식의 장단점, 제작에 필요한 설계 조건 및 기초 자료 등을 고찰하여 보았다.

• Proceedings of the KSEEG Conference
• /
• 2007.04a
• /
• pp.306-309
• /
• 2007

• Proceedings of the KSEEG Conference
• /
• 2007.04a
• /
• pp.310-312
• /
• 2007

• The Journal of Engineering Geology
• /
• v.22 no.1
• /
• pp.49-58
• /
• 2012

Anchor heads a recommonly exposed to surface weathering processes that cause physical damage by vibration and external forces. This study presents a new method of anchor-head installation that uses near-surface embedding based on analyses of concrete block failure. ABAQUS 3D numerical modeling performed to compare this method with the standard technique and to analyze the distribution of displacement and the stress pattern. In addition, application of the method to a real-world case was tested by in-situ measurements. The results show a maximum vertical stress of 9.73 MPa and vertical displacement of 1.34 mm. Field tests indicated that displacement of a concrete block was 3 to 4 times greater than that of an embedded bearing plate.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.11
• /
• pp.79-89
• /
• 2008

In this study, a series of undrained cyclic triaxial tests were performed with three different consolidation stress ratios ($K_c$=1.0, 1.5, 2.0) to investigate the undrained shear strength characteristics of sands with respect to the amount of contained silt located around the basin of Nak-dong River. The test results show that the more the sand has silt, the lower is cyclic shear stress ratio (CSR) in all $K_c$ and that the higher $K_c$ goes, the larger CSR decreases due to the increase of contained silt. The excessive pore pressure caused during shearing has an influence on the decrease of CSR by the high initial pore pressure in proportion to the amount of contained silt regardless of the $K_c$ value. After consolidation, the analysis of the skeleton void ratio of the sample reveals that the main cause of the decrease of CSR as well as the increase of the initial excessive pore pressure is the increase of the skeleton void ratio in proportion to the amount of contained silt.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.6
• /
• pp.460-472
• /
• 2023

This study was conducted based on the case of an accident (excessive deformation) that occurred during the hydraulic test of a shipboard tank manufactured in accordance with the design regulations. Over-pressure phenomenon was noted as the main cause of accidents in the process of testing tanks without physical damage, which can be found in external factors such as cross-sectional difference between inlet pipe and air pipe and higher water filling rate than the recommended one. The main goal of this paper is to establish a safe water filling rate according to the range of sectional area ratio(SAR) reduced below the regulations for each test situation. The simulation was conducted in accordance with the hydraulic test procedure specified in the Ship Safety Act, and the main situation was divided into two types: filling the tank with water and increasing the water head to the test pressure. The structural safety evaluation of the pressure generated inside the tank and the effect on the structure during the test was reviewed according to the SAR range. Based on the results, guidelines for the optimal filling rate applicable according to SAR during the hydraulic test were presented for the shipboard tanks used in this study.