• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.226.1-226.1
• /
• 2010

본연구에서는 GTL(gas to liquids)공정의 합성가스 생산을 위해 수증기-이산화탄소 복합개질반응(Combined Steam and Carbon dioxide Reforming of Methane, CSCRM)을 수행하였다. CSCRM은 수증기와 이산화탄소의 공급비 조절을 통해 $H_2$/CO비를 2로 맞추기 용이한 장점을 지니고 있어 다른 단일 개질 반응과 달리 합성가스 생산 시 $H_2$/CO 비율을 조절하기 위한 부가적인 공정이 필요하지 않아 경제적인 공정이다. 일반적으로 사용되는 Ni개질촉매는 가격대비 우수한 성능을 보이지만 S/C비가 낮은 CSCRM의 경우 촉매표면의 탄소침적에 의한 비활성화가 야기되는 문제점이 있다. 따라서 본 연구에서는 산소저장능력과 산소전달능력이 우수한 $CeO_2$를 조촉매로 첨가하여 표면에 형성된 코크 제거가 용이하도록 하였다. Ni-Ce/$MgAl_2O_4$촉매는 동시함침법(co-impregnation)으로 제조하였으며, Ni의 함량을 10wt%로 고정한 상태에서 Ce의 함량을 조절하여 Ce/Ni 최적비를 찾고자 하였다. XRD, TPR, BET, $H_2$-Chemisorption과 같은 촉매의 특성분석을 통해 촉매의 비표면적, 환원특성과 Ni입자의 분산도 등을 확인하였다. Ce를 첨가함에 따라 Ce2.5wt%까지는 비표면적이 증가하다가 이후 점차 줄어드는 경향성을 보였다. 또한, $H_2$-Chemisorption 결과 역시 비표면적과 유사한 경향성을 보였는데, Ce5.0wt%까지 Ni 분산도가 증가 하다가 다시 감소하는 것을 확인할 수 있었다. 반응실험은 $H_2O:CO_2:CH_4:N_2$ = 0.8:0.4:1:1의 공급조건에서 수행하였으며, 질소와 수소 환원분위기로 $700^{\circ}C$에서 1시간 환원 후 $650^{\circ}C$에서 $550^{\circ}C$범위로 온도를 떨어뜨려가면서 반응을 수행하였다. Ce를 첨가함에 따라 $CH_4$ 전환율이 증가를 하다가 Ce2.5wt% 이후 감소하는 것을 확인할 수 있었다. 이러한 높은 촉매 활성은 Ce 첨가로 인해 환원특성이 좋아지고 Ni분산도가 증가하여 담체와 강한 상호작용(SMSI)을 형성함으로 탄소침적 저항성 강화에 기인한 것이다.

• Membrane Journal
• /
• v.27 no.3
• /
• pp.205-215
• /
• 2017

Polymer membranes are cheap and easy in fabrication, and show a high permeability and selectivity, thus play pivotal roles in gas separation as well as water purification. However, polymer membranes typically exhibit the trade-off relation between permeability and selectivity; i.e. when the permeability is high, the selectivity is low and vice versa. Facilitated transport has been considered one of the solutions to address this issue. Over the last decades, facilitated transport concept had played an important role in preparing the membranes and providing ideal and various models for the transport. Understanding the nature of carrier, the mobility of matrix and the physico-chemical properties of polymer composites are crucial for facilitated transport. Depending on the mobility of carrier, facilitated transport membrane is classified into three; mobile carrier membrane, semi-mobile carrier membrane, fixed-site carrier membrane. Also, there are four types of reversible reaction between the carrier and the specific target; proton transfer reaction, nucleophilic addition reaction, p-complexation reaction and electrochemical reaction. The facilitated transport membranes have been applied in the separation of CO2, O2 and olefin (propylene or ethylene). In this review, major challenges surrounding facilitated transport membranes and the strategies to tackle these challenges are given in detail.

• Resources Recycling
• /
• v.10 no.3
• /
• pp.51-59
• /
• 2001

Impurities removal from waste carbon black was carried out to produce high-grade carbon black. A large amount of hydrophilic carbon black is produced as a byproduct of the hydrogen production process by flame decomposition of water. Due to its impurities content such as sulphur, iron, ash, etc., it can only be used as low-grade carbon or burnt out. High-grade hydrophilic carbon black is 3~5 times more expensive than oil-based carbon black because of high production cost associated with process complexly and pollutant treatment. Hydrophilic carbon is normally used for conductive materials for batteries, pigment for plastics, electric wire covering, additives for rubber, etc. In these applications, impurity content must be blow 1 fe. In this study, magnetic separation, froth flotation and ultrasonic treatment were employed to remove impurities from the low-grade hydrophilic carbon black. Results showed that the ash, iron and sulphur content of product decreased to less than 0.01 wt.%, 0.01 wt.% and 0.3 wt % respectively and the surface area of product was about 930 $m^2$/g for conductive materials.

• Applied Chemistry for Engineering
• /
• v.19 no.1
• /
• pp.1-16
• /
• 2008

Titanium dioxide ($TiO_2$) is one of the most researched semiconductor oxides that has revolutionised technologies in the field of environmental purification and energy generation. It has found extensive applications in heterogenous photocatalysis for removing organic pollutants from air and water and also in hydrogen production from photocatalytic water-splitting. Its use is popular because of its low cost, low toxicity, high chemical and thermal stability. But one of the critical limitations of $TiO_2$ as photocatalyst is its poor response to visible light. Several attempts have been made to modify the surface and electronic structures of $TiO_2$ to enhance its activity in the visible light region such as noble metal deposition, metal ion loading, cationic and anionic doping and sensitisation. Most of the results improved photocatalytic performance under visible light irradiation. This paper attempts to review and update some of the information on the $TiO_2$ photocatalytic technology and its accomplishment towards visible light region.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.420-427
• /
• 2017

Recently, the depletion of fossil fuels, global warming and environmental pollution have emerged as a worldwide problem, and studies of new renewable energy sources have been progressed. Among the many renewable energy sources, the use of bio fuel has the potential to displace fossil fuels due to low price, easy to handle, and the abundant sources. Pyrolysis oil (PO) derived from waste wood and sawdust is considered an alternative fuel for use in diesel engines. On the other hand, PO is limited to diesel engines because of its low cetane number, high viscosity, high acidity, and low energy density. Therefore, to improve its poor properties, PO was mixed with alcohol fuels, such as ethanol. Early mixing with ethanol has the benefit of improving the storage and handling properties of the PO. Furthermore, a PO-ethanol blended fuel was injected separately, which can be fired through pilot-injected diesel in a dual-injection diesel engine. The experimental results showed that the substitution of diesel with blended fuel increases the amount of HC and CO, but reduces the NOx and PM significantly.

• Journal of the Korean Electrochemical Society
• /
• v.19 no.1
• /
• pp.21-27
• /
• 2016

Vanadium redox flow batteries (VRFBs) using the electrolytes containing various vanadium ions in sulfuric acid as supporting solution are one of the energy storage devices in alternatively charging and discharging operation modes. The positive electrolyte contains $V^{5+}/V^{4+}$ and the negative electrolyte $V^{2+}/V^{3+}$ depending on the operation mode. To prevent the mixing of two solutions, proton exchange membranes are mainly used in VRFBs. Nafion 117 could be the most promising candidate due to the strong oxidative property of $V^{5+}$ ion, but causes high crossover of electroactive species to result in a decrease in coulombic efficiency. In this study, the composite membranes using Nafion ionomer and porous polyethylene substrate were prepared to keep good chemical stability and to decrease the cost of membranes, and were compared to the properties and performance of the commercially available electrolyte membrane, Nafion 117. As a result, the water uptake and ionic conductivity of the composite membranes increased as the thickness of the composite membranes increased, but those of Nafion 117 slightly decreased. The permeability of vanadium ions for the composite membranes significantly decreased compared to that for Nafion 117. In a single cell test for the composite membranes, the voltage efficiency decreased and the coulombic efficiency increased, finally resulting in the similar energy efficiency. In conclusion, the less cost of the composite membranes by decreasing 6.4 wt.% of the amount of perfluorinated sulfonic acid polymer due to the introduction of porous substrate and lower vanadium ion permeability to decrease self-discharge were achieved than Nafion 117.

• Journal of Plant Biotechnology
• /
• v.34 no.2
• /
• pp.111-118
• /
• 2007

Global warming crisis due primarily to continued green house gas emission requires impending change to renewable alternative energy than continuously depending on exhausting fossil fuels. Bioenergy including biodiesel and bioethanol are considered good alternatives because of their renewable and sustainable nature. Bioethanol is currently being produced by using sucrose from sugar beet, grain starches or lignocellulosic biomass as sources of ethanol fermentation. However, grain production requires significant amount of fossil fuel inputs during agricultural practices, which means less competitive in reducing the level of green house gas emission. By contrast, cellulosic bioethanol can use naturally-growing, not-for-food biomass as a source of ethanol fermentation. In this respect, cellulosic ethanol than grain starch ethanol is considered a more appropriate as a alternative renewable energy. However, commercialization of cellulosic ethanol depends heavily on technology development. Processes such as securing enough biomass optimized for economic processing, pretreatment technology for better access of polymer-hydrolyzing enzymes, saccharification of recalcitrant lignocellulosic materials, and simultaneous fermentation of different sugars including 6-carbon glucose as well as 5-carbon xylose or arabinose waits for greater improvement in technologies. Although it seems to be a long way to go until commercialization, it should broadly benefit farmers with novel source of income, environment with greener and reduced level of global warming, and national economy with increased energy security. Mission-oriented strategies for cellulosic ethanol development participated by government funding agency and different disciplines of sciences and technologies should certainly open up a new era of renewable energy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.202-202
• /
• 2012

유연성 투명 전도막은 현대 전자산업의 발전에 있어 필수적인 부품소재로서, 가시광선의 투과율이 80% 이상이고 면저항이 $100{\Omega}/sq.$ 전후이며 휘거나 접히고 나아가 두루마리의 형태로도 응용이 가능한 소재를 일컫는다. 이러한 유연성 투명 전도막은 차세대 정보디스플레이 산업 및 유비쿼터스 사회의 중심이 되는 유연성 디스플레이, 터치패널, 발광다이오드, 태양전지 등 매우 다양한 분야에 응용이 기대된다. 이러한 이유로 고 신뢰성 유연성 투명 전도막 개발기술은 차세대 산업에 있어서의 핵심기술로 인식되고 있다. 현재로서는 인듐 주석 산화물(indium tin oxide; ITO) 및 전도성 유기고분자를 사용하여 투명 전도막을 제조하고 있으나, ITO 박막의 경우 인듐 자원의 고갈로 인한 가격상승 및 기판과의 낮은 접착력, 열팽창계수의 차이로 인한 공정상의 문제, 산화물 특유의 취성으로 인한 유연소자로서의 내구성 저하 등의 문제가 제기되고 있다. 전도성 유기고분자의 경우는 낮은 전기전도도와 기계적강도, 유기용매 처리 등의 문제점이 지적되고 있다. 따라서 높은 전기전도도와 투광도 뿐만 아니라 유연성을 지니는 재료의 개발이 요구되고 있는 실정이다. 최근 이러한 재료로서 그래핀(graphene)과 탄소나노튜브(carbon nanotube; CNT)를 중심으로 하는 탄소나노재료가 주목받고 있으며 많은 연구가 활발히 진행되고 있다. 본 연구에서는 열화학기상증착법(thermal vapor deposition; TCVD)으로 합성된 그래핀 및 CNT를 이용하여 탄소나노재료 복합체 기반의 유연성 투명 전도막을 제작하고 그 특성을 평가하였다. 그래핀과 CNT합성을 위한 기판으로는 각각 300 nm 두께의 니켈과 1 nm 철이 증착된 실리콘 웨이퍼를 이용하였으며, 원료가스로는 메탄(CH4)과 아세틸렌(C2H2)등의 탄화수소가스를 이용하였다. 그래핀의 경우 원료가스의 유량, 합성온도, 냉각속도를 변경하여 대면적으로 두께균일도가 높은 그래핀을 합성하였으며, CNT의 경우 합성시간을 변수로 길이 제어합성을 도모하였다. 합성된 그래핀은 식각공정을, CNT는 스프레이 증착공정을 통해 고분자 기판(polyethylene terephthalate; PET) 위에 순차적으로 전사 및 증착하여 탄소나노재료 복합체 기반의 유연성 투명 전도막을 제작하였다. 제작된 탄소나노재료 복합체 기반의 유연성 투명 전도막은 물리적 과부하를 받았을 때 발생할 수 있는 유연성 투명 전도막의 구조적결함에 기인하는 전도성 저하를 보상하는 특징이 있어, 그래핀과 탄소나노튜브 각각으로 제조된 유연성 투명 전도막보다 물리적인 하중이 반복적으로 인가되었을 때 내구성이 향상되는 효과가 있다. 40% 스트레인을 반복적으로 인가하였을 때 그래핀 투명 전도막은 20 사이클 이후에 면저항이 $1-2{\Omega}/sq.$에서 $15{\Omega}/sq.$ 이상으로 급증한 반면 그래핀-CNT 복합체 투명 전도막은 30사이클까지 $1-2{\Omega}/sq.$ 정도의 면저항을 유지하였다.

• Korean Journal of Food Science and Technology
• /
• v.40 no.5
• /
• pp.485-490
• /
• 2008

In this study, organic tea leaves were characterized with the aim of developing an organic beverage process. The green tea leaves grown using organic farming techniques were collected in Haenam, Korea. Catechins in green tea leaves were extracted by chloroform and ethyl acetate and these were then analyzed quantitatively and qualitatively by HPLC (high pressure liquid chromatography). The color and pH values of the green tea extracts were also measured. The catechin levels of April-harvested, May-harvested and June-harvested, semi-fermented leaves at 0.5% were 66.24, 29.19, 57.11, and 5.27 ${\mu}g/mL$, respectively. Among the detected catechins, the level of (-)-epigallocatechin gallate was the highest while that of (-)-epigallocatechin was not detected. The June-harvested leaves were selected as raw material for development of the green tea beverage, based on the levels of catechins, economic viability and yield of tea extract. As the level of extract increased, the levels of catechins of 0.1, 0.2, 0.5% also increased by 1.5, 11.78 and 41.01 times. From the results of the sensory evaluation of June-harvested leaf-extract, the sensory score of color was the highest in 0.1%, while the flavor and overall quality were the highest in 0.2%.

• Resources Recycling
• /
• v.26 no.3
• /
• pp.79-91
• /
• 2017

The core of Hydrogen Fuel Cell Vehicles (FCV) is polymer solid fuel cell (PEFC), and the core material that generates electrochemical electricity in the cell is platinum catalyst. Platinum is localized in South Africa and Russia, and the world production of Pt is about 178 tons per year, which is expensive and recycled. At present, the amount of Pt used in PEFC is $0.2{\sim}0.1mg/cm^2$. In order to reduce the price of the battery and increase the FCV supply, the target is to reduce the amount of Pt used to $0.05{\sim}0.03mg/cm^2$. $Pt-Pd/Al_2O_3$, Pt/C, Pt/GCB, Pt/Au/C, PtCo/C, PtPd/C, etc. by using polyol method using nano Pt, improved Cu-UPD/Pt substitution method and nano-capsule method, Have been researched and developed, and there have been reported techniques for improving the activity of Pt catalysts and stabilizing them. This paper investigates the production technology of nano-Pt and nano-Pt catalysts, recycling of spent Pt catalysts and application trends of Pt catalysts.