• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.462-466
• /
• 2009

We investigated the pore properties of inorganic membranes applied for hydrogen separation industry. Inorganic membranes were derived from polysilazanes. The thermal reactions involved were studied using thermogravimetry(TG) and IR spectroscopy(FTIR) of the solids. To determine the thermal effect of pore properties, polysilazanes were pyrolysed in inert atmosphere. Pore volume and BET surface area showed the maximum value at a pyrolysis temperature of $500^{\circ}C$. For amorphous SiCN membrane derived from polysilazanes, selectivity of $H_2/N_2$ was 4.81 at $600^{\circ}C$.

• Membrane Journal
• /
• v.33 no.2
• /
• pp.70-76
• /
• 2023

Heavy water (D₂O) can induce various biochemical changes in comparison with light water (H₂O). In order to reduce excessive energy consumption, which is a disadvantage of the existing separation process, we conduct the forward osmosis with electrospun polyamide membranes. NaCl and phosphoric acid were used as draw solutions. FT-IR spectroscopy was used to quantify the concentration of heavy water. It was observed that phosphoric acid could concentrate heavy water through a forward osmosis process and its special interaction with hydrogen/deuterium (H/D) was spectrophotometrically confirmed.

• Membrane Journal
• /
• v.24 no.3
• /
• pp.213-222
• /
• 2014

In this study, 2-stage recirculation membrane process was developed for purification of high purity bio-methane for the vehicle fuel application. Pure gas permeation and mixture gas permeation test were done as a function of methane content and pressure in the feed using polysulfone membrane modules. 2-stage membrane plant was designed, constructed in a food waste treatment cite. Dehumidification, dry desulfurization, and desiloxane plants are installed for the removal of $H_2O$, $H_2S$ and siloxane in the biogas. Permeation test were done with the pre-treated methane mixture in terms of methane purity and recovery by adjusting the ratio of membrane area (1:1, 1:3, 2:2) in the first and second membrane modules in the plant. When membrane area of 2 stage increased to $3m^2$ from $1m^2$ at 1-stage membrane area of $1m^2$, the feed rate and $CH_4$ recovery at 95% methane purity were increased from 47.1% to 92.5% respectively. When the membrane area increased two-fold (1:1 to 2:2), $CH_4$ recovery increased from 47.1% to 88.3%. When the feed flow rate was increased, in 1:3 ratio, final purity of the methane is reduced, the methane recovery is increased. When operating pressure was increased, the feed rate was increased and recovery was slightly decreased. From this result, membrane area, feed pressure and feed rate could be the important factor to the performance of the membrane process.

• Korean Chemical Engineering Research
• /
• v.54 no.6
• /
• pp.847-853
• /
• 2016

Here has been examined a 3-dimensional computational fluid dynamics (CFD) modeling in order to investigate the performance analysis of proton exchange membrane (PEM) fuel cells with serpentine flow fields. The present CFD model considers the isothermal transport phenomena in a fuel cell involving mass, momentum transport, electrode kinetics, and potential fields. Co-current flow patterns for a PEMFC are considered for various geometries in the single straight cell. Current density distribution from the calculated distribution of oxygen and hydrogen mass fractions has been determined, where the activation overpotential has been also calculated within anode and cathode. CFD results showed that profiles differ from those simulations subjected to each the calculated activation overpotential. It is interesting that the present serpentine flow field shows the specific distribution of current density with respect to the aspect ratio of depth to width and the ratio of reaction area for various serpentine geometries. Simulation results were considered reasonable with the other CFD results reported in literature and global comparisons of the PEMFC model.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.6
• /
• pp.248-256
• /
• 2012

A Pd-based hydrogen membranes for hydrogen purification and separation need high hydrogen perm-selectivity. The surface roughness of the support is important to coat the pinholes free and thin-film membrane over it. Also, The pinholes drastically decreased the hydrogen perm-selectivity of the Pd-based composite membrane. In order to remove the pinholes, we introduced various surface pre-treatment such as alumina powder packing, nickel electro-plating and micro-polishing pre-treatment. Especially, the micro-polishing pretreatment was very effective in roughness leveling off the surface of the porous nickel support, and it almost completely plugged the pores. Fine Ni particles filled surface pinholes with could form open structure at the interface of Pd alloy coating and Ni support by their diffusion to the membrane and resintering. In this study, a $4{\mu}m$ surface pore-free Pd-Cu-Ni ternary alloy membrane on a porous nickel substrate was successfully prepared by micro-polishing, high temperature sputtering and Cu-reflow process. And $H_2$ permeation and $N_2$ leak tests showed that the Pd-Cu-Ni ternary alloy hydrogen membrane achieved both high permeability of $13.2ml{\cdot}cm^{-2}{\cdot}min^{-1}{\cdot}atm^{-1}$ permation flux and infinite selectivity.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.2
• /
• pp.98-107
• /
• 2017

Pd-based membranes have been widely used in hydrogen purification and separation due to their high hydrogen diffusivity and infinite selectivity. However, it has been difficult to fabricate thin and dense Pd-based membranes on a porous stainless steel(PSS) support. In case of a conventional PSS support having the large size of surface pores, it was required to use complex surface treatment and thick Pd coating more than $6{\mu}m$ on the PSS was required in order to form pore free surface. In this study, we could fabricate thin and dense Pd membrane with only $3{\mu}m$ Pd layer on a new PSS support manufactured by metal injection molding(MIM). The PSS support had low surface roughness and mean pore size of $5{\mu}m$. Pd membrane were prepared by advanced Pd sputter deposition on the modified PSS support using fine polishing and YSZ vacuum filling surface treatment. At temperature $400^{\circ}C$ and transmembrane pressure difference of 1 bar, hydrogen flux and selectivity of $H_2/N_2$ were $11.22ml\;cm^{-2}min^{-1}$ and infinity, respectively. Comparing with $6{\mu}m$ Pd membrane, $3{\mu}m$ Pd membrane showed 2.5 times higher hydrogen flux which could be due to the decreased Pd layer thickness from $6{\mu}m$ to $3{\mu}m$ and an increased porosity. It was also found that pressure exponent was changed from 0.5 on $6{\mu}m$ Pd membrane to 0.8 on $3{\mu}m$ Pd membrane.

• Membrane Journal
• /
• v.11 no.4
• /
• pp.179-189
• /
• 2001

Effect of ozonation on permeate flux was studied by using polysulfone ultrafiltration membrane. The filtration was first carried out by permeating phenol solutions under 3$kg_{f}$/$cm^2$ until steady-state flux was obtained. Then, the ozone of concentration range between 10 and 45 mg/1.min was ozonated in water for reducing the fouling on the UF membrane. Treatment of chemical wastewater by combined ozone and membrane filtration methods was also investigated for the final purpose. The Fenton method assisted by chemical coagulation was employed as a prtreatment method and found to be highly efficient in removing a large amount of organic compounds. And it was found that the ozonation made the permeate flux enhance in the phenol solution and phenolic-chemical wastewaster by 10% and oxidation by ozone and hydrogen peroxide was more effective. Evidence was presented that TMP decreased in more ozone concentrated water and it was found that the ozone-mediated membrane would have a limited role to prevent the membrane fouling rather than to eliminate fully.

• Membrane Journal
• /
• v.29 no.5
• /
• pp.252-262
• /
• 2019

A sulfonated star branched poly(styrene-b-butadiene-b-styrene) triblock copolymer (SSBS) was synthesized with varying degrees of sulfonation. The effective sulfonation on the butadiene block was confirmed by FT-IR spectroscopy. Ion exchange capacity by titration was used to determine the degree of sulfonation. The synthesized polymer observed enhanced water uptake and proton conductivity. At room temperature, the SSBS with 25 mol% degree of sulfonation showed an outstanding proton conductivity of 0.114 S/cm, similar to that of commercial membrane, Nafion. The effect of temperature at constant relative humidity on conductivity resulted to a remarkable increase in proton conductivity. Methanol permeability studies showed a value lower than Nafion for all the sulfonated membranes. Structural nature observed using AFM showed that the membranes observed microphase separated nanostructures and the connectivity of the interionic channels.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.1
• /
• pp.19-24
• /
• 2012

Barium zirconate exhibits good thermo-chemical stability and proton conduction at high temperatures, but shows poor electron conductivity. Therefore, for high efficiency of hydrogen separation, a very thin and dense Pd-Barium zirconate membrane has to be coated on a porous substrate. A thin and dense Pd-Barium zirconate membrane was successfully synthesized on a porous substrate by means of dual sputtering method. The structural and chemical features of the $BaZr_{0.85}Y_{0.15}O_{3-{\delta}}$ membranes sputtered at $300^{\circ}C$ and $400^{\circ}C$ were investigated by X-ray diffractometry, and it was found that a well-crystallized membrane, Pm-3m space group of $BaZrO_3$, was synthesized. The surface and cross-sectional morphologies of membrane were assessed by SEM (scanning electron microscopy) and TEM(transmission electron microscopy) of the surface and of cross sections. The cross sectional observation of Pd-$BaZr_{0.85}Y_{0.15}O_{3-{\delta}}$ membrane by dual sputtering shows that the coating is quite dense with columnar structure.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1999.10a
• /
• pp.1-2
• /
• 1999

시간과 공간의 구애를 받지 않는 양질의 음성, 화상, 문자정보의 교환을 위한 노력으로 디지털 휴대폰과 휴대용 컴퓨터가 등장하면서 음성과 문자정보의 교환분야에 커다란 진보를 이룩하였다. 그러나 현재는 휴대폰이 음성정보에 문자정보교환이 추가된 상황이기 때문에, 아직도 관련 정보교환기술 및 기기개발이 진행되고 있다. 앞으로 휴대폰과 휴대용 컴퓨터의 기능을 통합하고 화상정보까지 결합된 휴대용 정보기기를 위해서는 전자회로의 집적화 및 통신속도 증대가 필수적이다. 또한 이들 휴대용 정보기기를 구동시키기 위한 전력도 증가될 것으로 예측되기 때문에, 현재 전원으로 사용되는 2차전지보다 에너지 밀도가 더욱 증패된 전지가 요구될 것으로 예상된다. 그리고 내연기관의 배기에 의해 발생되는 환정오염문제를 해결하기 위한 방법중의 일환으로 전기자동차 개발이 진행되고 있으며, 이들 전기자동차에 2차전지를 장착하기 위해서 경제성이 있고, 고속충전이 가능하고, 안전성이 높은 고에너지 밀도의 2차 전지 개발이 요구되고 있다. 현재 2차전지는 음극재료나 양극재료에 따라 낚축전지, 니켈/카드륨(Ni/Cd) 전지, 니켈/수소(Ni/MH) 전지, 라륨 2 차전지등이 있으며, 전극재료의 고유특성에 의해 전위와 애너지 밀도가 결정된다. 특히 리튬 2차전지는 리튬의 낮은 산화환원전위와 분자량으로 인해 에너지 밀도가 높기 때문에 앞에서 언급한 휴대용 전자기기의 구동전원으로 많이 사용되고 있다. 리튬 2차전지는 음극 재료가 금속리튬인 경우는 리튬금속으로, 탄소재료인 경우는 리튬이온이라 하며, 한편으로 전해질이 고체 고분자이거나 혹은 역체 유기용매와 리튬염을 고분자와 혼성시킨 겔(gel)인 경우는 고분자로, 전해짙이 리튬염이 전리되어 있는 유동성 액체일 경우는 고분자를 생략하여 구분하고 있다. 즉 리튬금속 2 차전지(LB), 리튬이온 2 차전지(LIB), 리튬금속 고분자 2차전지(LPB), 리튬 이온 고분자 2차전지(LIPB)로 크게 구분된다. 금속리듐을 음극으로 사용하고 전해질로는 리튬염이 전리되어 있는 액체유기용매 를 사용한 리튬금속 2차전지는, 금속리튬전극이 충방전 과정을 반복하면서, 전리된 리튬이 균일하게 산화환원되지 못하고 표변에서 양극방향으로 성장하는 수지상 (dendrite) 현상으로 인해 안전성 확보에 문게가 있었다. 리튬과 알루미늄 합금형태로 음극에 사용한 동전형 전지는 상용화 되었지만, 이러한 단점을 개선하기 위해 리튬이온이 금속으로 석활되는 환원반응전위보다 높은 전위에서 전극재료가 충전되면서 리튬이온이 저장되고, 방전되면서 배출되는 탄소를 음극재료로, 그리고 리튬이온이 충방 전시 가역적으로 삼입 탈리되는 층상의 리튬금속산화물을 양극으로 구성하고, 엑체 전해질과 다공성 고분자 분리막을 사용한 것이 LIB이다. LIB에서 리튬이온의 이동이 가능한 액체전해질의 가능을 고분자 전해질이 대신함으로서 보다 높은 안정성을 확보 한 전지가 LIPB 이다. 또한 고분자 전해질을 사용한 경우 금속리튬상에서의 수지상 성장이 저하되는 현상이 관찰됨으로서, 이론용량이 3,860mAh/g 에 달하는 리튬금속 혹은 합금을 고분자 전지에서 음극으로 사용하고자 하는 2 차전지가 LPB 이다. 리튬 2차전지는 비록 1989년 액체전해질을 사용한 금속리튬 2차전지의 실패전력을 안고있지만 궁극적으로는 이론적으로 최대의 에너지밀도를 가지고 있는 LPB를 지 향할 것으로 예상되지만 가까운 장래에 실현되기는 어려울 것이다. 따라서 향후의 라튬 2차전지의 전개방향은 현재의 LIB를 고분자 전해질을 채용하는 LIPB로 진행시커면서 저가의 전극재료개발을 지속적으로 추진할 것으로 예상된다. 현재 리튬 2차전지는 소형전지에 국한되고 있지만 전기자동차나 전력저장용으로 이를 대형화시커기 위해서는 열적특성이 우수하고 저가인 전극재료개발이 선행되야하기 때문에, 저가의 탄소재료와 코발트산화물을 대신할 수 있는 철, 망칸 또는 니켈산 화물의 개발이 필요하다.