• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.2
• /
• pp.171-178
• /
• 2016

An aircraft in flight and ATC(: Air Traffic Controllers) working in the Ground Control Center carry out a voice communication using the radio. Voice signal to be transmitted from the aircraft is received to a plurality of terrestrial sites around the country at the same time. The ATC receives the various quality of voice signal from the aircraft depending on the distance, speed, weather conditions and adjusted condition of the antenna and the radio. The ATC carries out a voice communication with aircraft in the optimal conditions finding the best voice signal. However, the present system chooses the values of the CD(: Carrier Dectect) which is determined to be superior to, based on the input voice level, as optimal channel. Thus this system can not be seen to select the optimal channel because it doesn't consider the effect of the noise which influences on the communication quality. In this paper, after removing the noise in the voice signal, we could give the digitized information and an improved voice signal quality, so that users can select an optimal channel. By using it, when operating the training eavesdropping system or the aircraft control, we can expect prevention accident and improvement of training performance by selecting the improved quality channel.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.2C
• /
• pp.95-112
• /
• 2007

Spatial Multiplexing techniques, which is a kind of Multiple antenna techniques, provide high data transmission rate by transmitting independent data at different transmit antenna with the same spectral resource. OFDM (Orthogonal Frequency Division Multiplexing) is applied to MIMO (Multiple-Input Multiple-Output) system to combat ISI (Inter-Symbol Interference) and frequency selective fading channel, which degrade MIMO system performance. But, orthogonality between subcarriers of OFDM can't be guaranteed under high-mobility condition. As a result, severe performance degradation due to ICI is induced. In this paper, both ICI and CAI (Co-Antenna Interference) which occurs due to correlation between multiple antennas, and performance degradation due to both ICI and CAI are analyzed. In addition to the proposed CIR (Channel Impulse Response) estimation method for avoiding loss in data transmission rate, HIC (Hybrid Interference Cancellation) approach for guaranteeing QoS of MIMO-OFDM receiver is proposed. We observe the results on analytical performance degradation due to both ICI & CAI are coincide with the simulation results and performance improvement due to HIC are also verified by simulation under SCM-E Sub-urban Macro MIMO channel.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.3
• /
• pp.161-163
• /
• 2014

We consider the device-to-device (D2D) communication underlaying multi-cell interference system, in which the cellular downlink (DL) resource is reused by K cells and two D2D transmission links within each cell. In this paper, it has been shown that the downlink intra-cell and inter-cell interference can be effectively handled by interference alignment (IA) technique, as long as the simultaneous D2D links are properly selected or power-controlled so that they may not incur interference to the base stations in the same and neighbor cells. In particular, we provides the IA technique that can achieve the theoretically maximum possible degree of freedom (DOF), demonstrating that a total of (K+1)M degrees of freedom (DOFs) can be achieved for K-cell interference system with two underlaying D2D links, where base stations, cellular UE's, and D2D UE's all have M transmit and receive antennas.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.182-190
• /
• 2011

A amplitude modulation(AM) range measuring system utilizes the phase difference of the modulated envelope of the reflected signal to measure the distance. It is known that the AM system has a problem in accuracy due to antenna leakage signals and spurious reflection signals, but an AM range measurement system using an active reflector, which shifts the frequency bands, has been proposed in order to minimize the measurement errors due to spurious signals. In this paper, a new phase measurement module for the AM range measurement system, which enables to measure long distance with good accuracy, is proposed. The modulation frequency is alternatively selected between 8 and 1 MHz, and the measured distance range with this module is up to 150 m within 2 cm accuracy. A JK flip-flop circuit is used for higher phase accuracy, and an XOR circuit is used to cover long distance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.2
• /
• pp.358-365
• /
• 2007

In this paper, the effects of transmit beamforming on downlink performance in DS-CDMA communication systems are investigated. The uplink and downlink in FDD systems use different carrier frequencies. If the downlink uses the same weighting vectors as the uplink, the antenna beam for downlink is formed with certain DOA shift and it thus affects the beamforming gain. So, the impacts of different frequencies on the downlink beam patterns are studied. One possible algorithm to convert uplink beamforming weights to downlink, which is called frequency-calibrated processing, is also evaluated to reduce the degradation of downlink performance due to different frequencies. Under frequency selective channels, the downlink chooses a PUPW beamforming scheme when the uplink employs a PPPW vectors. To form a beam pattern for a PUPW after combining the downlink PPPWs converted from the uplink PPPWs, three approaches are studied. One method is to consider only one dominant path and thus obtain a single main-beam. In the others, multiple-beams weighted with the magnitudes of all paths and equally weighted with all paths are constructed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.4
• /
• pp.833-838
• /
• 2011

RFID system in manufacturing industry is used to collect, categorize, and process the data of products. To install RFID system for a large factory, a large amount of wired data communication network is necessary for RS232 communication. If the installed location of RFID system in the factory is changed or extended, a reinstallment is required for the already installed wired data network. A large amount of time/financial reinvestment is necessary for such reinstallation. By using wireless data communication network, however, the initial installation and reinstallation are very simple. In this paper, we implemented a wireless communication system and RFID system. We used the CC1020 chip for wireless communication system and EM4095 chip for RFID system. CC1020 chip enables highly-reliable data communication, and by setting a simple status register, it can switch between transmitting/receiving status and it can choose the desired frequency of either 400 MHz or 900 MHz. Also, Communication range is 50 m, if external antenna is used. EM4095 is a chip for RFID reader system with the carrier frequency of 125 KHz. This chip can implement the reader system by connecting a small number of components. And EM4100 was used for RFID system. EM4100 is read-only type. Atmega128 is used to control a wireless communication system and RFID system. We confirm that the system can communicate without error up to 50 m from sender. In the paper, the circuit diagram and operation program for CC1020 and RFID system are presented. The system used in the experiment is shown in pictures, and the data movement pattern of CC1020 is shown in the diagram, and the performance of each transmission method is presented.