• Journal of Power System Engineering
• /
• v.18 no.5
• /
• pp.144-149
• /
• 2014

The silencer of 155mm caliber howitzer is developed to reduce its firing loud noise. This kind of research of a large gun was seldom because its big firing noise does not make significant effect even if to use silencer. Nowadays, military facilities became closely located civilian residential area. The noise would be regarded environmental pollution. So the noise reducing research becomes reconsidered. The previous silencer researches were only dealt with small guns as pistols and rifles moreover their theories was not properly analyzed for a large caliber silencer. The reason was previous researches of a large caliber silencer as 155mm howitzer were limited because their data based on simulation results without actual test by using computational fluid dynamics. In this study, the entire processes of silencer of 155mm caliber howitzer which were design, manufacturing, actual firing test, and analysis of its theories, were performed and showed. In particular, the actual noise of with silencer and without was measured and the results were compared to analyze the effect of silencer.

• Journal of Environmental Health Sciences
• /
• v.32 no.2 s.89
• /
• pp.118-125
• /
• 2006

The road traffic noise has been increasing broader effects on urban areas as well as rural areas because of rapidly increasing traffic volume and newly-constructed roads. 10 sites in building development areas were selected and the noise levels were measured by the apartment floors and by the various block plans of apartment complex. The results showed that the highest traffic noise level was obtained at the 5 and 7 floors on the apartment floors. On the basis of 7 floor with the highest level, the correction coefficient obtained from noise reduction by each floor and measurement point was -5.54 dB(A)(1st floors), -0.96 dB(A)(3rd floors), -0.38 dB(A)(5th floors), 0.00 dB(A)(7th floors), -1.98 dB(A)(l0th floors), -3.10 dB(A)(13th floors), -3.45 dB(A)(15th floors). The level of road traffic noise in the arrangement construction of right angle was about 3.0 dB(A) at N-4 point and 2.1 dB(A) at N-6 point lower than that of a plan figure, respectively. The results suggested that application of correction coefficient obtained by the apartment floor and by the arrangement construction can be improved in road traffic noise.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.5
• /
• pp.309-316
• /
• 2018

Various studies have been conducted to improve the BSR (Buzz, Squeak, Rattle) noise generated irregularly while the vehicle is running. In vehicle, When an external force such as vibration or force flows into the contact surface, BSR noise is generated at the contact surfaces of nearby components. In this paper, BSR conceptually explain the kind of noise generation mechanisms and the basic principles of generation, which have been proven by observing and improving noise phenomena in automobiles over the last 10 years. Through this, it is expected that researchers who want to study BSR related improvement research not only in automobiles but also in other industries, It will be able to understand the BSR phenomenon and provide a framework for thinking out improvement ideas and to carry out further research.

• Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
• /
• 2003.10a
• /
• pp.173.2-174
• /
• 2003

국내 보급되고 있는 곡물건조기는 열풍형 순환식 곡물건조기가 주종을 이루고 있는데, 이건조기의 경우 곡물이 순환하면서 열풍공급과 템퍼링과정을 반복하면서 건조가 이루어지는 대류열전달 방식을 채택하고 있다. 대류열전달 방식은 복사열전달 방식에 비해 열전달률이 낮기 때문에 건조속도와 열효율이 떨어지며, 건조시 미질 향상과 건조비용 절감에 한계가 있어 왔다. 따라서 건조에너지의 절감과 동시에 고품질 쌀 생산을 할 수 있는 새로운 형식의 곡물건조기술을 확립하고자 원적외선 곡물건조기를 개발하였다. 원적외선은 0.56~l,000$\mu\textrm{m}$의 전자파로서 세라믹 도료표면에 열을 가하면 원적외선 파장대의 강한 에너지를 얻을 수 있다. 이같은 원적외선 에너지를 농산물에 조사시키면 열이 침투하게되고 동시에 농산물의 내부온도가 상승함에 따라 활발한 분자운동을 하면서 수분을 표면으로 이동시키기 때문에 열풍건조방법에 비해 열전달효율이 높고, 농산물을 보다 균일하게 건조가 가능하므로 좋은 품질의 쌀을 생산할 수 있는 특징을 가지고 있다. 시작기는 1회 3,800kg을 건조할 수 있도록 설계하였고, 템퍼링실, 건조실, 열풍실, 승강기 등으로 구성되었다. 원적외선 방사체의 형태는 실린더형이고, 방사체가 설치된 열풍실 위쪽은 타공망, 아래쪽은 방사량을 높이기 위하여 일부 개방된 구조로 제작하였다. 본 연구에서 구명된 원적외선 방사체 길이와 조사거리는 각각 1,470mm, 125mm가 적절한 것으로 나타났다. 시작기의 성능시험을 열풍건조기(대비구)와 비교한 결과 소음은 대비구에서의 94.12dB보다 13% 가량 낮게 나타났고, 건조온도를 45$^{\circ}C$로 설정하고 벼를 건조했을 때 건감률 0.58%,wb로 대비구의 0.47%,wb 보다 23% 높았고, 건조소요에너지도 470kcal/kg - water로 2%의 절감되었다. 또한 건조한 벼를 도정하여 색, 냄새, 윤기, 찰기 등에 대한 관능검사결과는 원적외선 건조방법이 종합기호도가 6.37으로 열풍건조방법 6.13보다 우수한 평가를 받았다. 건조비용은 시작기의 구입가격이 20% 비싸기 때문에 시간당 고정비가 높았으나, 건조성능이 우수하여 건조비용이 69,350원/톤으로 대비구보다 14% 절감되는 것으로 나타났다.

• Journal of Digital Convergence
• /
• v.11 no.1
• /
• pp.225-236
• /
• 2013

The voice recognition has been made continuously. Now, this technology could support even natural language beyond recognition of isolated words. Interests for the voice recognition was boosting after the Siri, I-phone based voice recognition software, was presented in 2010. There are some occasions implemented voice enabled services using Korean voice recognition softwares, but their accuracy isn't accurate enough, because of background noise and lack of control on voice related features. In this paper, we propose a sort of multi-purpose preprocessor to improve this situation. This supports Keyword spotting in the continuous speech in addition to noise filtering function. This should be independent of any voice recognition software and it can extend its functionality to support continuous speech by additionally identifying the pre-predicate and the post-predicate in relative to the spotted keyword. We get validation about noise filter effectiveness, keyword recognition rate, continuous speech recognition rate by experiments.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.11 no.3 s.55
• /
• pp.33-42
• /
• 2007

In this study, for research on an improvement of the seismic safety of an EDG system, a small scale EDG system was manufactured. For the isolation system, the Coil Spring-Viscous Damper systems were selected. For the shaking table test, 3 kinds of seismic motions were selected which had different frequency contents. In this study, the isolation effects were different and they depended on the input seismic motion. In the case of an NRC earthquake which had low fiequency contents, the isolation effects of the horizontal direction were 20%. But for the seismic motions which had high fiequency contents, the isolation effects were $50{\sim}70%$. In the case of the vertical direction, poor isolation effects were observed. It was because the design properties and the real properties of the isolation system were a little different.

• Journal of the Korean Society of Safety
• /
• v.28 no.1
• /
• pp.24-28
• /
• 2013

This article evaluates the accuracy of noise measurements for 37 noise measurement applications for iPhone 4 and iPhone 3Gs. Noise levels were measured using simultaneously a precision sound level meter and iPhones installed noise measurement applications at the levels of 70 dB, 80 dB and 90 dB at 1,000 Hz. Measurement errors were estimated by subtracting two measurements between iPhone and sound level meter. It was found that measurement errors of 34 applications(89.2%) were greater than ${\pm}2$ dB which is the maximum allowable error range for the Type II sound level meter. It was only 4 applications that measurement errors lie within ${\pm}2$ dB error range. There was no significant differences among measurements with four iPhone 4s. However, there were significant differences between the measurements with iPhone 4 and iPhone 3Gs using the same application. It was due to the different hardware specifications such as microphone. Therefore, noise measurement applications, for example, which has to utilize hardware of the smartphone, should be programmed to identify hardware specifications and to adopt appropriate correction factors upon hardware specifications. In conclusion, it is necessary to check accuracy and validity before using the noise measurement applications for iPhones. Also, it was suggested that it should develop an evaluation guideline or protocol on accuracy testing for the measurement applications using a smartphone.

• Fire Science and Engineering
• /
• v.29 no.1
• /
• pp.53-59
• /
• 2015

Water hammering created by an unsteady flow in pipeline systems can cause excessive change in pressure, vibration, and noise. So, water hammer analysis is very important for limiting the damage caused to pipeline, pump and valve systems by operation conditions. On the other hand, water hammer arrester has been manufactured and used in order to minimize the damage caused by water hammering phenomenon in domestic, and it has been produced and installed as the low cost-oriented because of being no separate standard in the meanwhile. Therefore, our research team investigated about the standardization of water hammer arrester performance through the various methods, such as test methods for verification of one pipe, assuming the occurrence of water hammer in a water-based fire extinguishing system, separated for opening impact pressure and shut off impact pressure and for a branch pipe in order to make guideline for water hammer arrester performance. And finally, verified the performance of the water hammer pressure as the simple mechanical way using the U-shaped pipe and a test weight, so KFI standards for the water hammer arrester could be established.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.9
• /
• pp.4133-4137
• /
• 2011

Reliable Multi-Reader RFID identification is one of issues in Multi-Reader RFID realization program in recent. And the Multi-Reader RFID reader has difficulty to obtain reliable data in data capture layer. The reason is that unreliable readings such as a false positive reading and a false negative reading and missed readings can happen by reader collision problems, noise, or the mobility of tagged objects. We introduce performance metrics to solve these reader problems. We propose three solutions the Minimum Overlapped Read Zone (MORZ) with Received Signal Strength Indicator (RSSI), the Spatial-Temporal Division Access (STDA) method, and double bigger size of tags attached on the object. To show the improvement of the proposed methods, we calculate tag's successful read rates in a smart office, which consists of Multi-Reader RFID systems.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.6
• /
• pp.400-408
• /
• 2008

Multipurpose Dam, it produces electric energy by converting the potential energy into kinetic energy utilizing its head and quantity of the water. However, in this process, since during the time when the turbine connected to the hydraulic turbine generator revolves, there occurs a ceaseless loud noise, and due to this condition, it is true state that those people who work at inside of the power plant are damaging as hard as they are unable to concentrate on their work. Not only this, because the hydro-electric power generator room that locates at middle section between the hydraulic turbine room and the office is very large space volume, also since it was constructed chiefly by the reflecting material, it is functioning of amplify the noise when operating the generator, the soundproof measure against this condition is necessitated. On such viewpoint, I have presented the problem point of the relevant Hydraulic turbine dynamo and Hydraulic turbine dynamo room, and after improve such problem point, this study has ever investigated the satisfying degree about the noise-reduction at before and after of the improvement of soundproof measure, using the Auralizational technique that can experience virtual acoustic field. It is considering that such result could be utilized usefully as the fundamental material hereafter for the acoustic performance of the hydro-electric power generator room in dam and when its construction.