• The Journal of the Acoustical Society of Korea
• /
• v.26 no.5
• /
• pp.220-226
• /
• 2007

The two major objectives of acoustical measurements in a cavitation tunnel are measuring the noise levels generated by rotating propellers behind a hull and localizing possible noise sources in order to reduce noise levels. Propeller noise measurement experiments were performed in MOERI cavitation tunnel at December, 2006. In order to put the propeller into cavitating conditions, a wake-generating dummy body was devised. In addition, ten hydrophones are put inside a wing-shaped casing in order to minimize the unexpected flow induced self noise around hydrophone itself. After measuring both of the noises of the rotating propeller behind the dummy body and signals generated by a virtual source, respectively the data were matched field processed using the frequency incoherent Bartlett processor to localize noises on the propeller plane. In this paper, we presented the measured noise analysis and the localization results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.156-157
• /
• 2010

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.2
• /
• pp.18-28
• /
• 2008

In inverse acoustic problem with nearfield sources, it is important to separate multiple acoustic sources and to measure the position of each target. This paper proposes a new algorithm by applying MUSIC(Multiple Signal Classification) to the outputs of discrete wavelet transformation with sub-band selection based on the entropy threshold, Some numerical experiments show that the proposed method can estimate the more precise positions than a conventional MUSIC algorithm under moderately correlated signal and relatively low signal-to-noise ratio case.

• Proceedings of the KIEE Conference
• /
• 2008.04a
• /
• pp.121-122
• /
• 2008

본 논문에서는 2차 경로의 추정을 통하여 안정성이 강화된 능동소음 제어 시스템을 제안한다. LMS 알고리즘은 구조가 단순하고 계산량이 적은 장전이 있지만, 광대역 소음원에 적용할 경우 수렴 성능이 좋지 않은 단점이 있으며, 2차 경로 및 소음원 입력의 파워가 시변 할 경우 적응 알고리즘의 안정성이 약화되는 문제점이 발생한다. 본 논문에서는 지속적으로 누적 오차를 추적하여 일정 값 이상으로 증가하면 자동적으로 2차 경로 전달함수를 새로 추정하는 자동오프라인 추정 기법을 제안하였다. 공조용 덕트에 광대역 소음을 적용하여 제안된 능동소음제어 시스템을 실험을 수행한 결과 우수한 특성을 얻었다.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.5
• /
• pp.446-454
• /
• 2002

This paper presents the Doppler Scanning technique which enables us to detect the relative positions of moving distributed sources using Doppler frequency shift estimate when the moving source consists of distributed sources with different signature frequencies. Doppler frequency shifts of characteristic frequencies of machinery noise sources such as ship's generator and propeller, with tine along CPA (Closest Point of Approach of moving source) are unique, and can be functioned with respect to each source position. Therefore, this technique can be applied to estimate the relative geometrical positions between machinery noise sources. The Extended Kalman Filter (EKF) which has a high frequency resolution with high time resolution, is adopted for improving accuracy of Doppler frequency shift estimate geometric resolution of machinery positions since machinery noise sources show in general low frequency band characteristics with limited spacial distance. The performance of the technique is examined by the numerical simulations and is verified by the experiment using loudspeaker sources on the roof of the car.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.727-732
• /
• 2014

The goal is to find the position of the sound source with the TRM at reflections and refractions environment. The Fermat's principle applied to the ray tracing method are expected to follow the acoustic path in order to obtain acoustic distance and transmittance to. Utilizing them in the TRM was confirmed rear reflectance affect on estimated position, resolution and side lobe. And the TRM performance were superior to one of the beam forming techniques.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.483-489
• /
• 2009

The Time Difference of Arrival (TDOA) algorithm is being used widely for identifying the location of a source emanating either electrical or acoustic signal. It's application areas will not be limited to identifying the source at a fixed location, for example the origin of an earthquake, but will also include the trajectory monitoring for a moving source equipped with a GPS sensor. Most of the TDOA algorithm uses time correlation technique to find the time delay between received signals, and therefore difficult to be used for identifying the location of multiple sources. In this paper a TDOA algorithm based on cross-spectrum is developed to find the trajectory of two sound sources with different frequencies. Although its application is limited to for the sources on a disk plane, but it can be applied for identifying the locations of more than two sources simultaneously.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.235-240
• /
• 2001

A four degrees of freedom (dof) motion platform for bicycle simulator is developed. The motion platform, capable of the vertical linear and three angular motions, is designed based on analysis of the typical motion characteristics revealed by the existing six dof bicycle simulator. The platform essentially consists of two parts： the three dof parallel manipulator, consisting of a moving platform, a fixed base and three actuators, and the turntable to generate the yaw motion. The nonlinear kinematics and dynamics of the three dof parallel manipulator with multiple closed loop chains are analyzed for tracking control of the motion platform. The tracking performances of the three control schemes are experimentally compared： the computed torque method (CTM), the sliding mode control (SMC) and the PD control. The CTM and SMC, incorporated with the system dynamics model, are found to be equally better in performance than the PD controller, irrespective of the presence of external disturbance.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.7
• /
• pp.710-718
• /
• 2009

The time difference of arrival(TDOA) algorithm is being used widely for identifying the location of a source emanating either electrical or acoustic signal. It's application areas will not be limited to identifying the source at a fixed location, for example the origin of an earthquake, but will also include the trajectory monitoring for a moving source equipped with a GPS sensor. Most of the TDOA algorithm uses time correlation technique to find the time delay between received signals, and therefore difficult to be used for identifying the location of multiple sources. In this paper a TDOA algorithm based on cross-spectrum is developed to find the trajectory of two sound sources with different frequencies. Although its application is limited to for the sources on a disk plane, it can be applied for identifying the locations of more than two sources simultaneously.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.490-495
• /
• 2009

An approach to 3D visualization of multiple sound sources has been developed with the application of a moving array technique. Frequency-domain beamforming algorithm is used to generate a beam power map and the sound source is modeled as a point source. When a conventional delay and sum beamformer is used, it is considered that 2D distribution of sensors leads to have deficiency in spatial resolution along a measurement distance. The goal of moving an array in this study is to form 3D array aperture surrounding multiple sound sources so that the improved spatial resolution in a virtual space can be expected. Numerical simulation was made to examine source localization capabilities of various shapes of array. The 3D beam power maps of hemispherical and spherical distribution are found to have very sharp resolution. For experiments, two sound sources were placed in the middle of defined virtual space and arc-shaped line array was rotated around the sources. It is observed that spherical array show the most accurate determination of multiple sources' positions.