• Journal of the Korean Ceramic Society
• /
• v.37 no.10
• /
• pp.994-1000
• /
• 2000

Mn-Ni-Co계 스피넬을 모재로 선택하여 상업용 페라이트 등 다양한 종류의 Fe-스피넬과 동시 소결 가능성을 검토할 목적으로 각 소재의 소결 거동, 서미스터와의 계면 반응이나, 2차상의 형성 등에 대해 알아보았다. 대부분의 페라이트 조성이 Mn 스피넬과 새로운 2차상을 형성하지는 않는 것을 알 수 있었다. 상업용 페라이트의 경우 115$0^{\circ}C$ 소결 온도에서 접합이 가능한 조성은 다량의 액상이 존재하며 접합계면의 폭이 상대적으로 넓으므로 서미스터 특성에도 좋지 않은 영향을 줄 수 있을 것으로 생각된다. 반면에 MFN1과 MFN2 조성은 접합계면에서 새로운 2차상이 형성되지 않고 원소의 상호확산도 작아 NTC 서미스터의 동시소결용 보호재로서의 가능성이 높은 것으로 확인되었다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.3 no.1
• /
• pp.37-44
• /
• 1993

Calcia stabilized zirconia polycrystal (Ca-TZP) powders synthesized by hydrothermal treatment was sintered at a temperature range of $1200^{\circ}C~1400^{\circ}C$ and investigated the properties of sintered body and the behaviors of isothermal phase transformation. The sintered bodies of Ca-TZP were shown the density of about 97% and the average mean tetragonal grain size of about $0.1~0.25{\mu}m$. Also, Ca-TZP specimen was more stable during aging at $250^{\circ}C$ than that of Y-TZP ceramics.

• Journal of the Korean Ceramic Society
• /
• v.40 no.11
• /
• pp.1138-1140
• /
• 2003

To investigate the relation between the sintering degree and the elastic modulus of sintered glass, ball-milled commercial soda-lime-silica glass were used. It was heat-treated at various temperatures and for various times, and then the density and elastic modulus of sintered glass frit were measured. The experimental results showed a strong correlation between them.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.5
• /
• pp.995-999
• /
• 2007

The lead zirconate titanate (PZT) powders were synthesized to make the piezoelectric ceramics in low temperature as low as $900^{\circ}C$. To investigate the influence of additives on sintering of PZT, two kinds of sintering aids were made as follows; $wB_2O_3-xBi_2O_3-zCuO$and LiBiO2-CuO. The sintering aid, $1{\sim}3$ wt.% $LiBiO_2-CuO$, was added into these PZT powders and the specimens were fired at temperature in the range of $800{\sim}1200^{\circ}C$. The highest density was shown in the specimen with 1 wt.% $LiBiO_2-CuO$ as additive at temperature of $900^{\circ}C$. The sintered specimen were analyzed by X-ray diffraction(XRD) and scanning electron microscopy (SEM) was utilized to observe the microstructure, especially the densified morphology of specimens. In the XRD pattern, the well-crystallized PZT phase could be obtained in consequence of firing at $900^{\circ}C$. The scanning electron microscopy(SEM) was utilized to observe the structure of specimens after firing at $900^{\circ}C$. The densified perovskite structure of $PbZrTiO_3$ could be obtained by sintering at temperature as low as $900^{\circ}C$. The high sinterability of PZT ceramics was attributed to the low formation temperature of the liquid phase of additives.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.1
• /
• pp.65-69
• /
• 2003

Microstructural and electromagnetic properties of YIG ferrites, (Y, Ca)-(Fe, V, In, Al)-O for Isolator/Circulator were investigated with the sintering temperature. YIG ferrites of $Y_{2.1}Ca_{0.9}Fe_{4.4}V_{0.5}In_{0.05}Al_{0.05}O_{12}$ were fabricated by sintering at $1300^{\circ}C$, $1330^{\circ}C$, $1350^{\circ}C$, $1370^{\circ}C$. Crystallographic and microstructural properties were measured using XRD and SEM. Saturation magnetization$(4{\pi}M_s)$ were measured using VSM, and FMR(Ferromagnetic Resonance) experiment was conducted to measure ferromagnetic resonance line width$({\Delta}H)$. Microwave characteristics of YIG ferrites were measured using a Network Analyzer. The YIG ferrite of $Y_{2.1}Ca_{0.9}Fe_{4.4}V_{0.5}In_{0.05}Al_{0.05}O_{12}$, sintered at $1350^{\circ}C$, showed higher density, saturation magnetization and lower ferromagnetic resonance line width than those sintered at any other temperature.

• Resources Recycling
• /
• v.12 no.6
• /
• pp.8-12
• /
• 2003

According to the recent trend to raise the horizontal scan frequency to increase the image refinement of the High Definition TV and High Resolution Display, material with low core loss is required for the ferrite core for deflection yoke, which is secured even in the high frequency range. liking notice of the influence on the fine structure of Mg-Zn ferrite by the chemical com position and process, low temperature sintering was proceeded. Cu was added to the low loss Mg-Zn system ferrite. After select-ing MgO, ZnO, $Fe_2$$O_3$, CuO, MgO was substituted for CuO while varying the composition ratio. Then the sample was sintered for 3 hours between $980～1350^{\circ}C$ Magnetic permeability, power consumption, shrinkage rate, core loss were measured. The start-ing temperature to test the shrinkage of the sample was nearby $900^{\circ}C$, it increased according to the substitution process of Cu, and the firing temperature was lowered about $-50～-75^{\circ}C$ alongside of the process.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.11a
• /
• pp.266-270
• /
• 2004

SiC materials have been extensively studied for high temperature components in advanced energy system and advanced gas turbine because it has excellent high temperature strength, low coefficient of thermal expansion, good resistance to oxidation and good thermal and chemical stability etc. However, the brittle characteristics of SiC such as low fracture toughness and low strain-to fracture still impose a severe limitation on practical applications of SiC materials. For these reasons, SiC/SiC composites can be considered as a promising for various structural materials, because of their good fracture toughness compared with monolithic SiC ceramics. But, high temperature and pressure lead to the degradation of the reinforcing jiber during the hot pressing. Therefore, reduction of sintering temperature and pressure is key requirements for the fabrication of SiC/SiC composites by hot pressing method. In the present work, monolithic Liquid Phase Sintered SiC (LPS-SiC) was fabricated by hot pressing method in Ar atmosphere at $1800^{\circ}C$ under 20MPa using $Al_2O_3,\;Y_2O_3\;and\;SiO_2$ as sintering additives in order to low sintering temperature and sintering pressure. The starting powder was high purity $\beta-SiC$ nano-powder with all average particle size of 30mm. The characterization of LPS-SiC was investigated by means of SEM and three point bending test. Base on the composition of sintering additives-, microstructure- and mechanical property correlation, tire compositions of sintering additives are discussed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.8
• /
• pp.2150-2156
• /
• 2009

The effects of MgO and coloring agents on the physical properties and color of zirconia based ceramics with glass frit were studied. The addition of MgO was effective on the coloring of zirconia-20wt% glass frit system. Major factor on the coloring was turned out to be sintering temperature. Coloring agents was turned out to be more effective than the addition of MgO on the coloring of zirconia base ceramics. Specimen without glass frit showed drastic change in color, while specimen with 20wt% glass frit revealed a limited change in color. This means that the addition of glass frit suppresses the coloring of zirconia based ceramics. The effect of sintering temperature on coloring revealed little change in color.

• Journal of the Korean Ceramic Society
• /
• v.39 no.12
• /
• pp.1197-1202
• /
• 2002

In order to develope the porous $K_2Ti_6O_13$ whisker preform with good strength, the pore characteristics and compressive strength were investigated as a function of spark plasma sintering temperature. As a result, high porous whisker preform were successfully fabricated by sintering at 900∼950${\circ}C$ for 10 min under a pressure of 40 MPa, heating rate of 50${\circ}C$/min and on-off pulse type of 12:2. The whisker preform prepared under above optimum condition showed relatively high compressive strength of 174∼266 MPa, despite of high porosity ranging from 15% to 37%. This improvement in strength was considered to be mainly due to the spark-plasma discharges and the self-heating action between whiskers. The compressive strength of whisker preform, fabricated at sintering temperature less than 900${\circ}C$, showed 80∼100 MPa. This is low strength level less than one half times compared with whisker preform fabricated at 900∼950${\circ}C$. The whisker preform fabricated at 1000${\circ}C$ showed the highest compressive strength of 523 MPa, but resulted in low porosity of ∼5%. Based on above results, it was considered that spark plasma sintering was an effective method for developing high strength and porosity of whisker preform.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1999.05a
• /
• pp.60-60
• /
• 1999