• 대한기계학회논문집
• /
• 제17권1호
• /
• pp.120-130
• /
• 1993

본 연구에서는 니켈의 가공시 나타나는 공구의 마멸에 대한 정량화 및 절삭변 수와의 연관성에 대한 연구는 그 자체가 마멸에 대한 데이터 베이스 측면에서 중요하 고, 이러한 접근방법으로는 연구가 거의 이루어지지 않았다는 측면에서도 큰 의미를 갖는다. 본 연구는 특히 경도가 큰 공구인 CBN, 소결 다이아몬드(poly crystal dia- mond 이하 PCD), 단결정 다이아몬드(single crystal diamond 이하 SCD)공구를 사용하 여 니켈의 절삭에서 나타나는 공구의 마멸에 대한 분석을 선행한 후 수집한 정보로부 터 절삭속도, 이송, 절삭깊이 및 공구의 nose반경이 공구의 마멸 및 표면의 성상(su- rface quality)에 미치는 영향에 대하여 고찰하였고 절삭조건의 변화에 따라 마멸에 대한 예상 곡선을 구하였다.

• 한국생산제조학회지
• /
• 제6권2호
• /
• pp.102-111
• /
• 1997

This paper deals with the machinability based on turning of WC-Co allows with the coated and the sintered diamond tools. The main conclusions obtained are as follows. (1) When machining WC-10%Co alloy, the flank wear of sintered diamond tool increases more largely with the increase of cutting speed in comparison with coated diamond tool. The tool wear decreases with the increase of the grain size and nose radius of sintered diamond tool. (2) When machining WC-20%Co alloy, the tool wear and cutting force decrease with the decrease of rake angle. Their exists a certain cutting speed range to exhibit the smallest tool wear in machining the WC-20%Co alloy, and this critical cutting speed becomes higher by 2 times in the case of coated diamond tool compared with sintered diamond tool. (3) The machinability becomes better with the increase of Co content. The effects of cutting speed and feed rate on the roughness of machined surface become smaller with the increase of Co content.

• 대한기계학회논문집A
• /
• 제20권4호
• /
• pp.1216-1224
• /
• 1996

In the use of glass fiber reinforced plastics it is often necessary to cutting the components, but the cutting GFRP is often made difficult by the delamination of composites and the short tool life. In this paper, the machinability of GFRP by mean of tool materials and type was experimentally investigated. By proper selection of cutting tool material and type excellent machining of this workpiece is achieved. The surface quality relate closely with the feed rate and cutting tools.

• Journal of Welding and Joining
• /
• 제30권4호
• /
• pp.19-23
• /
• 2012

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 춘계학술발표강연 및 논문개요집
• /
• pp.28-28
• /
• 2003

고온가압소결(Hot Pressing) 된 다이아몬드 공구용 Co-Fe, Co-Ni계 금속본드의 상온 건식 미끄럼 마멸시험을 행하고, 조성에 따른 각 본드의 마멸 특성을 비교하고 마멸 기구를 규명하였다. 미끄럼 마멸시험은 pin-on-disk 형태의 마멸시험기를 사용하여 각 조성의 성분, 적용하중 그리고 마멸상대재를 변수로 상온, 대기 중에서 실시되었다. 마멸속도는 마멸시험 전후의 시편의 무게 감량을 이론밀도와 거리로 나누어 계산되었다. 마멸기구의 규명을 위하여 시험된 시편의 마멸면과 마멸단면을 SEM과 EDS를 이용하여 분석하였다. 시험 결과 Co-Fe system의 경우 그 마멸속도는 마멸상대재의 영향보다는 Fe 첨가에 따른 시편의 미세조직과 기계적 성질의 차이에 따라 크게 변화하였다. 그러나 Co-Ni system의 마멸속도는 마멸 상대재에 따라 크게 변화하는 것이 관찰되었다. $Al_2$O$_3$를 상대재로 마멸된 경우에는 마멸속도가 시편/상대재 접촉면에서 형성되는 산화층의 영향을 크게 받았고, glass bead(83% SiO$_2$)를 상대재로 한 경우에는 시편의 경도와 마멸속도는 서로 반비례하였다.

• 한국정밀공학회지
• /
• 제24권2호
• /
• pp.33-40
• /
• 2007

In this study, presintered and full sintered low purity alumina ceramics were machined with various tools to clarify the effect of cutting fluid in machinability. The main conclusions obtained were as follows. When the presintered ceramics were wet machined with sintered diamond tool, the tool wear becomes extremely large, and higher cutting speed can be used than in the case of full sintered ceramics. The productivity of wet cutting with the sintered diamond tool is much higher than that of dry cutting. In the case of the CBN and ceramic tools, the tool wear were smaller at wet cutting than at dry cutting, especially exhibiting considerably larger grooved tool wear in wet cutting with ceramic tool.

• 대한기계학회논문집
• /
• 제13권4호
• /
• pp.604-610
• /
• 1989

본 연구는 알루미나계 세라믹의 소결 다이아몬드 공구로 절삭시의 칩의 형태 와 절삭저항을 관찰하였다. 절삭 양식은 건식과 습식으로 하고, 여러 가지 적삭조건 에 따른 flank 마멸의 진행과정, 가공면의 표면거칠기에 미치는 영향 및 가공면의 크랙 상태를 조사형 현미경으로 확대 검출하여 가공상태를 정밀하게 조사, 측정하였 다.

• 한국정밀공학회지
• /
• 제23권1호
• /
• pp.80-88
• /
• 2006

In this study, unsintered and presintered low purity alumina ceramics were machined with various tools to clarify the machinability and the optimum cutting conditions. The main conclusions obtained were as fellows. Machined with ceramic tool, the ceramics presintered at the temperature range of $1000\~1100^{\circ}C$ showed the best machinability due to the adhesion formed in weared surface within a certain cutting speed range. In the above combination and conditions, the ceramic tool showed the highest productivity through all experiments. The life of CBN tool was longer in machining of the ceramics presintered at $1000^{\circ}C$ than in the case of that presintered at $600^{\circ}C$, but the diamond tool showed adverse tendency. In machining of the ceramics presintered at $1000^{\circ}C$, the ceramic tool exhibits the longest tool life in high speed, the tool lives became extremely worse in the order of CBN tool and diamond tool. However, in the case of the ceramics presintered at $600^{\circ}C$, the diamond tool shows the longest tool life, the tool lives was much worse in the order of CBN tool and ceramic tool.

• 한국정밀공학회지
• /
• 제25권12호
• /
• pp.47-54
• /
• 2008

Hard turning process can be defined as a single-point machining process carried out on "hard" materials. The process is intended to replace or limit traditional grinding operations that are expensive, environmentally unfriendly, and inflexible. The purpose of this study is to achieve a systematic understanding of machining characteristics and the effects of machining parameters on cutting force, tool wear shape and chip formation by the outer cutting of a kind of wear resistant tungsten carbide V30. Hard turning experiments were carried out on this alloy using the PCD (Poly Crystalline Diamond), cBN (cubic Boron Nitride) and PcBN (Polycrystalline cubic Boron Nitride) cutting tools. The PcBN and the usual cBN tools were used to be compare with the PCD tool and the dry turning was carried out. The PcBN is attractive as the tool material which replaces the PCD. The tool wear width and cutting force were measured, and the worn tool and chip were observed. The difference of the tool wear mechanism among the three tool materials was investigated.

• 한국기계가공학회지
• /
• 제10권1호
• /
• pp.73-79
• /
• 2011

In this study, coring with diamond core drill on the sintered $Al_2O_3$ ceramic plate were carried out with different coring conditions such as various cutting speed and feed rate to evaluate their effectiveness on the wearing behavior of diamond tool and coring quality. The wearing rate of diamond core drill were getting better with increasing cutting speed and feed rate but the quality of cored hole were getting worse as increasing cutting speed and feed rate.