• 전기학회논문지P
• /
• 제58권1호
• /
• pp.85-89
• /
• 2009

We investigated the quench characteristics in accordance with increase of turns number of trigger coil and shunt resistance of matrix-type superconducting fault current limiter (SFCL) with $2{\times}3$ array. The matrix-type SFCL consists of the trigger part to apply magnetic field and the current-limiting part to limit fault current. The fault current limiting characteristics according to the increase of magnetic field and applied voltage were nearly same. This is because the application of magnetic field hasn't an affect on total impedance of the SFCL. When turns number of a reactor increased, the voltage difference between two superconducting units in the current-limiting part according was decreased. The resistance difference generated in two superconducting units was also decreased. Therefore, we confirmed that the differences of the critical behaviors between superconducting units were reduced by application of magnetic field. By this results, we could decide the optimum turns number of reactor to apply magnetic field.

• 전기학회논문지
• /
• 제67권8호
• /
• pp.1055-1061
• /
• 2018

Recently, due to the rapid development of electric vehicle and energy storage system, it is emphasized for battery management system to be needed and to be improved. BMS carries out various movement for optimization the use of the energy and safe use of secondary battery, these movement of BMS start at high wattage shunt fixed resistor which performs a function for detecting current among the BMS components. In addition, for the safe operation of secondary battery, the reliability of current voltage variation detected from shunt should be secured, and for corresponding characteristics, the quality of Temperature coefficient of resistance for BMS shunt and the quality of Thermo electromotive force all must be excellent. For these reasons, this study comes up with the stabilization plan for thermo electromotive force and temperature coefficient of resistance of BMS shunt resistor which is key to secondary battery operation.

• Composites Research
• /
• 제13권5호
• /
• pp.50-59
• /
• 2000

본 논문에서는 복합재료 패널 플러터를 억제할 수 있는 두 가지 방법에 대해서 연구하였다. 첫번째, 능동제어 방법에서는 선형 제어 이론을 바탕으로 제어기를 설계하였으며 제어입력이 작동기에 가해진다. 여기서 작동기로는 PZT를 사용하였다. 두 번째, 인덕터와 저항으로 구성되어진 션트회로를 사용하여 시스템의 감쇠를 증가시킴으로써 패널 플러터를 억제할 수 있는 새로운 방법인 수동감쇠기법에 대한 연구가 수행되었다. 이 수동감쇠기법은 능동적 제어보다 강건(robust)하며 커다란 전원 공급이 필요하지 않고 제어기나 감지 시스템과 같이 복잡한 주변 기기가 필요 없이도 실제 패널 플러터 억제에 쉽게 응용할 수 있는 장점을 가지고 있다. 최대의 작동력/감쇠 효과를 얻기 위해서 유전자 알고리듬을 사용하여 압전 세라믹의 형상과 위치를 결정하였다. 해밀턴 원리를 사용해서 지배 방정식을 유도하였으며, 기하학적 대변형을 고려하기 위해 von-Karman의 비선형 변형률-변위 관계식을 사용하였으며 공기력 이론으로는 준 정상 피스톤 1차 이론을 사용하였다. 4절점 4각형 평판 요소를 이용하여 이산화된 유한 요소 방정식을 유도하였다. 효율적인 플러터 억제를 위해 패널 플러터에 중요한 영향을 미치는 플러터 모드를 이용한 모드축약기법을 사용하였으며, 이를 통해 비선형 연계 모달 방정식이 얻어지게 된다. 능동적 제어 방법과 수동 감쇠 기법에 의해 수행되어진 플러터 억제 결과들을 Newmark 비선형 시분할 적분법을 통해 시간 영역에서 살펴 보았다.

• 한국전기전자재료학회논문지
• /
• 제34권2호
• /
• pp.126-129
• /
• 2021

We fabricated plate typed shunt resistors composed of carbon nanotube (CNT) and metal alloy for measuring DC current. CNT plates were prepared from dispersed CNT/Urethane solution by squeezing method. Cu/Ni alloys were prepared from composition-designed alloy wires for adjusting the temperature coefficient of resistance (TCR) by pressing them. As well, we fabricated a hybrid resistor by squeezing the CNT/Urethane solution on the metal alloy plate directly. In order to confirm the composition ratio of the Cu/Ni alloy, we used an energy-dispersed X-ray spectroscopy (EDX). Cross-section and surface morphology were analyzed by using a scanning electron microscopy (SEM). Finally, we measured the initial resistance of 2.35 Ω at 25℃ for the CNT paper resistor, 7.56 mΩ for the alloy resistor, and 7.38 mΩ for the hybrid resistor. The TCR was also measured to be -778.72 ppm/℃ at the temperature range between 25℃ to 125℃ for the CNT paper resistor, 824.06 ppm/℃ for the alloy resistor, and 17.61 ppm/℃ for the hybrid resistor. Some of the hybrid resistors showed a near-zero TCR of 1.38, -2.77, 2.66, and 5.49 ppm/℃, which might be the world best-value ever reported. Consequently, we could expect an error-free measurement of the DC current using this resistor.