• 한국세라믹학회지
• /
• 제38권7호
• /
• pp.608-614
• /
• 2001

수지결합질 탄소재의 사출성형시 중요한 요소는 열유변학적 거동이다. 수지결합질 탄소재의 열유변성, 기계적 물성은 충진제(흑연)의 표면상태에 영향을 받는다. Coupling 처리에 의한 충진제의 표면개질은 binder와의 젖음성과 호환성 등에 영향을 미쳐 수지결합질 탄소재의 특성을 향상시킨다. 본 연구에서는 충진제의 표면개질을 위해 실란 coupling 처리하였다. 충진제의 표면에 코팅된 실라놀은 FT-IR과 침수거동 관찰결과 충진제 표면에 단층으로 코팅되었음을 보였다. Coupling 처리는 충진제 표면에 활성을 가함으로써 수지결합질 탄소재의 열유변학적 거동과 기계적 물성에 기여하였다.

• 한국세라믹학회지
• /
• 제32권5호
• /
• pp.559-566
• /
• 1995

Alumina powder was coated with stearic acid and then mixed with isotactic polypropylene, atactic polypropylene as binders at 15$0^{\circ}C$ for 2 hours. The mixture was then injection molded at various mold temperatures using injection molding machine to investigate the effect of the molding temperature and debinding parameters on the formation of the defects. The molded specimens were debinded in both air and nitrogen atmospheres. Wicking and solvent methods were also used to enhance debinding efficiency. The specimens were prefired at 120$0^{\circ}C$ and then sintered at 150$0^{\circ}C$ for 3 hours. Various defects were formed at mold temoperature of 3$0^{\circ}C$, 6$0^{\circ}C$ and 10$0^{\circ}C$ and any noticeable defect was not formed at 85$^{\circ}C$. The density of green body increased with mold temperature. Debinding in air atmosphere was more effective than in nitrogen atmosphere. Results also proved that wicking and solvent treatments helped minimize the number of defects.

• 한국세라믹학회지
• /
• 제46권3호
• /
• pp.229-233
• /
• 2009

This study has focused on manufacturing technique of powder injection molding of watch case made from zirconia powder. A series of computer simulation process was applied to prediction of the flow pattern in the inside of the mould to clarifying the change of sintering shrinkage depended on flow direction. The material properties of melted feedstock inclusive of the PVT graph and thermal viscosity flowage properties were measured for obtaining the input data in computer simulation. Also, molding experiment was conducted and the results of experiment showed that good agreement with simulation results for flow pattern and weld line location. On the other hand, gravity and inertia effect have an influence on velocity of melt front because of high density of ceramic powder particles in powder injection molding against the polymer injection molding process. In the experiment, the position of melt front was compared with upper gate and lower gate position. The gravity and inertia effect could be confirmed in the experimental results.

• 한국세라믹학회지
• /
• 제48권6호
• /
• pp.648-653
• /
• 2011

Generally the piezo-composites have superior hydrostatic response characteristics than PZT ceramics due to both the stress amplification effect in axial direction and stress reduction effects in radial direction. This paper described material properties of a 1-3 type piezo-composite that fabricated with ceramic injection molding (CIM) technology. The electro-mechanical performances of the composite have been analyzed using FEM and the physical properties of the composite have been measured with the vol% of the PZT ceramics. Based on the results, the $k_t$ increased rapidly as the vol% of the PZT ceramics increased up to 30 vol% and saturated the constant value in the above region. Also the experimental results have good agreement with the simulation values of the composite. Finally we developed the composites having high piezoelectric properties than the PZT ceramics with the CIM technology.

• 한국산학기술학회논문지
• /
• 제15권5호
• /
• pp.2587-2593
• /
• 2014

세라믹 사출공정(CIM)은 산업 분야 전반에 걸쳐 널리 사용되고 있는 공정 중 하나로, 점차 의료용 전자기기의 부품 등으로 확대 적용되고 있다. 본 연구에서는 FEM 해석을 통해 CIM의 공정변수가 제품의 품질에 미치는 영향을 분석했다. 단순평판 형상의 해석결과를 기초로 구멍이 있는 형상, 모서리부가 둥근 형상 및 측벽 구조가 있는 형상 등과 비교 분석했다. 구멍이 있는 형상의 경우, 구멍 주변에 밀도분포가 고르지 못하며 용접선(weld-line)과 같은 결함이 발생할 수 있음을 예측할 수 있었다. 반면 제품의 모서리부 반경이 크면 성형성 및 유동성이 좋아지는 것을 확인했다. 따라서 CIM 공정변수 뿐만 아니라 제품의 형상변수도 고려해야 한다. 해석결과 온도, 초기분율, 속도 등의 공정변수는 제품의 품질 향상을 위한 중요한 설계 변수가 될 수 있음을 확인할 수 있었다.

• 한국정밀공학회지
• /
• 제9권4호
• /
• pp.109-117
• /
• 1992

Mixing of ceramic-binder system was investigated experimentally and theoretically for application to Ceramic Injection Molding. Polypropylene, stearic acid, and paraffin wax were selected as the binder system, and silicon nitride fine powders were selected as the ceramic material. Single screw ectruder was employed as the mixing equipment. Theoretical analysis was performed to investigate the mixedness of mixture quantitatively. The analysis predicted average residence time average total strain, and average shear stress as a function of screw speed for mixtures of different volume fraction. Qualitative mixedness of mixture and characteristics of mixing were investigated by using SEM and EPMA. In addition, rheological properties of the mixture were investigated by using a capillary rheometer to examine possibility of injection molding.

• 열처리공학회지
• /
• 제36권4호
• /
• pp.215-222
• /
• 2023

3Y-TZP (3 mol% yttria-stabilized tetragonal zirconia polycrystals, 3Y-TZP) ceramics are emerging as dental implant materials due to their superior optical and mechanical properties as well as excellent biophysical properties, in spite of low bioactivity. In this study, we investigated to sintered properties and microstructural defects of dental zirconia implants fabricated by ceramic injection molding and post-HIP (Hot isostatic pressing) processing and analyzed the processing parameters related with the obtainment of its high sinterd density. Sintered and microstructural parameters, i.e, apparent density, grain size and phase composition of zirconia implants fabricated by injection molding were dependent on the fixtute size and implant type. Maximum sintered density of 99.2% and minimum grain size of 0.3-0.4 ㎛ were obtained from large-scaled 2-body sample. In 1-body ceramic implant, high sintered density of 99.5% was obtained, but it had a little monoclinic phase and wide grain size distribution.

• 한국세라믹학회지
• /
• 제35권2호
• /
• pp.172-179
• /
• 1998

Valve lifter namely tappet is supported by lifter hole which is located upper side of camshaft in cylinder block transforms rotatic mvement of camshaft into linear movement and helps to open and shut the en-gine valve as an engine parts. The face of valve lifter which is continuously contacting with camshaft brings about abnormal wears such as unfair wear and early wear because it is severely loaded in the valve train system. These wears act as a defect like over-clearance and cause imperfect combustion of fuel during the valve lifting in the combustion chamber. Consequently this imperfect combustion makes the engine out-put decrease and has cause on air pollution. To prevent these wears therefore The valve lifter cast in me-tal developed into SiC ceramics valve lifter which has an excellence in wear and impact resistance As a results the optimum process conditions like injection condition mixture ratio and debonding process could be established. After sintering fine-sinered dual microstructure in which prior ${\alpha}$-SiC matches well with new SiC(${\beta}$-SiC) produced by reaction among the ${\alpha}$-SiC carbon and silicon was obtained. Based on the study it is verified that mechanical properties of SiC valve lifter are excellent in Vickers hardness 1100-1200 bending strength (300-350 Pa) fracture toughness(1.5-1.7 Mpa$.$m1/2) Through engine dynamo test-ing SiC valve lifter and metal valve lifter are examined and compared into abnormal phenomena such as early fracture unfair and early wear. It is hoped that this research will serve as an important springboard for the future study of heavy duty diesel engine parts developed by ceramics which has a good wear resis-tance relaibility and lightability.

• 한국기계가공학회지
• /
• 제16권6호
• /
• pp.63-68
• /
• 2017

The purpose of this study is to improve the whitening phenomenon around the PET preform gate for blow molding. CAE analysis of plastic injection molding has been applied to design of preform shape and select the injection molding conditions. A ceramic insulation gate with lower thermal conductivity than metal is applied to improve the whitening phenomenon created around the gate in the injection molding process. According to the results of CAE analysis, the warpage deformation at the square corner was estimated to be about 0.34 mm at the bottom. From the results of the temperature history analysis, it was confirmed that the resin near the gate cooled more rapidly than the cavity. Ceramic insulated gates were fabricated to reduce the cooling rate and experiments were conducted to confirm the effectiveness of the whitening phenomenon improvement. As a result of the ceramic insulation gate experiment, it was confirmed that the whitening phenomenon was significantly reduced around the gate.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2000년도 추계학술대회
• /
• pp.226-229
• /
• 2000

일반적으로 안경집은 일회적으로 사용하고 버리는 것이라 생각하는 사람이 많다. 안경집을 주로 생산하고 있는 대동사출금형과의 공동 노력으로 다기능성 안경집을 개발한 것을 소개한다. 일상적인 고정관념을 버리면 편리하고 기능성이 높은 제품을 만들 수 있다는 신념으로 개발한 결과 어린이나 젊은이들이 졸아할 문방구 겸용 안경집을 개발할 수 있었다. 완구는 소비자가 일상적으로 많이 접촉하기 때문에 곰팡이나 세균이 서식하지 않도록 항균 세라믹을 이용하여 항균처리하였다. 또한 상온에서 인체에 이로운 원적외선이 방출될 수 있도록 고안하였다. 단순한 색상의 무료함을 줄이기 위하여 어린이나 젊은이들이 좋아하는 상용화된 캐릭터를 사용하여 제품의 다양화를 꾀하였고, 4개의 조각으로 만들어 어린이들이나 젊은이들이 조립할 수 있도록 하여 흥미를 더할 수 있도록 하였다. 또한 소비자들이 선호하는 색을 알아보기 위하여 기존의 안경집을 활용하여 색상성호도 조사를 실시하였다. 젊은층은 자극적이고 화려한 색깔을 선호하는 한편 기성세대는 무난한 색깔을 선호하였다. 또한 콘택트 렌즈를 착용하는 경우에도 안경을 사용하는 경우가 많다. 이 경우 콘택트 렌즈와 안경을 따로 가지고 다녀야 하는 불편이 있다. 이에 착안하여 안경과 콘택트 렌즈를 겸용으로 사용하는 소비자를 위하여 안경과 콘택트 렌즈를 동시에 담을 수 있는 안경집을 개발(실용신안 출원번호:8928)하였다. 이 고안은 콘택트 렌즈를 안경집에 보관하기 위한 것으로 콘택트렌즈가 식염수에 잠겨 보관된 렌즈캡을 안경집내에 별도로 삽입되는 케이스에 수납하도록 구성하여 안경과 함께 콘택트 렌즈를 보관해 휴대하는 안경집 보관용 콘택트 렌즈 케이스에 관한 것으로 이것의 특징은 뚜껑이 열리고 닫히도록 구성된 안경집에 있어서 뚜껑 안쪽에 거울이 마련되고 뚜껑이 연결되는 선단부 안쪽에 끼움홈과 체결홈이 형성된 체결부를 갖는 안경집과 이것에 결합되는 체결구가 마련되어 개폐되는 커버가 형성된 케이스로 구성된다.로 금형설계 및 제작기간을 단축하고자 한다.ere demonstrated in rats after i.c.v., intraperitoneally and orally administration, respectively. The antiepileptical effects by the combination of compounds from ginseng; were compared with the iuluence of Rg1, Rb1, Rc and with the well known antiepileptical drugs such as carbamazepine, valproic acid. The base for the research is obtained by using the WAG/Rij strain (Luijtelaar, Coenen, Kuznetcova), an excellent genetic model for human generalized absence epilepsy. The improving action of gensinosides was effectively demonstrated on the model of electrical kindling of amygdala of WAG/Rij rats with genetically determined absences, and the influences of ginsenosides on the slow wave discharges have also been being investigated. The different characteristics of a kindling process exerted in the sex-different region of the amygdala and demonstrated that the level of sex steroids and content of neurosteroids in amygdaloid tissue ca