• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.11a
• /
• pp.198-199
• /
• 2013

To prevent energy waste in buildings used heat insulator. Heat insulator materials can be classified inorganic and organic. The inorganic material has lower water resistance. The inorganic material is heavy and worse thermal performance than organic materials. Technologies on energy saving and materials used in curtain walls have progressed with increase of high-rise and large buildings. However, there is little study to explain water resistance performance of the curtain walls. This study focused on evaluation of insulation of inorganic materials and performance evaluation by thermal conductivity.

• Journal of the Korean Ceramic Society
• /
• v.41 no.3
• /
• pp.221-228
• /
• 2004

Basic properties of artificial lightweight aggregate by using waste dusts and strength properties of LWA concrete were studied. Bulk specific gravity and water absorption of artificial lightweight aggregates varied from 1.4 to 1.7 and 13 to 16%, respectively. Crushing ratio of artificial lightweight aggregate was above 10% higher than that of crushed stone or gravel. As a result of TCLP leaching test, the leaching amount of tested heavy metal element was below the leaching standard of hazardous material. Slump, compressive strength and stress-strain properties of LWA concrete made of artificial lightweight aggregate were tested. Concrete samples derived from LWA substitution ratio of 30 vol% and W/C ratio of 45 wt% showed the best properties overall. Thermal insulation and sound insulation characteristics of light weight concrete panel with the optimum concrete proportion were tested. Average overall heat transmission of 3.293W/㎡$^{\circ}C$ was observed. It was higher by about 15% than those of normal concrete made by crushed stone. Sound transmission loss of 50.9 ㏈ in frequency of 500 ㎐ was observed. It was higher by about 13% than standard transmission loss.

• Journal of the Korean Ceramic Society
• /
• v.51 no.3
• /
• pp.170-176
• /
• 2014

Effective glass frit compositions enabled to absorb laser energy, and to seal a commercial dye-sensitized solar-cell-panel substrate were developed by using $V_2O_5$-based glasses with various amounts of $TeO_2$ substitution. The latter was intended to increase the lifetime of the solar cells. Substitution of $V_2O_5$ by $TeO_2$ provided a strong network structure for the glasses via the formation of tetrahedral pyramids in the glass, and changed the various glass properties, such as glass transition temperature ($T_g$), dilatometric softening point ($T_d$), crystallization temperature, coefficient of thermal expansion (CTE), and glass flowage without any detrimental effect on the laser absorption property of the glasses. The thermal expansion mismatch (${\Delta}{\alpha}$) between the glass frit and the substrate could be controlled within less than ${\pm}5%$ by addition of 10 wt% of ${\beta}$-eucryptite. An 810 nm diode laser was used for the sealing test. The laser sealing test revealed that the VZBT20 glass frit with 10 wt% ${\beta}$-eucryptite was successfully sealed the substrates without interfacial cracks and pores. The optimum sealing conditions were provided by a beam size of 3 mm, laser power of 40 watt, scan speed of 300 mm/s, and 200 irradiation cycles.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.4
• /
• pp.365-372
• /
• 2018

3D printing technology of construction field can be divided into structural materials, interior and exterior finishing materials, and is mainly done by extruding and adapting. Particularly when it is applied as an exterior materials, it is mainly applied to an unstructured exterior materials and high accuracy is required. The exterior materials can be used as a cement composite materials, it is suitable also for a additive type manufacturing, and the role of a redispersible polymer powder is important. But, high temperatures, redispersible polymer cement base material beget dehydration and micro crack of cement matrix. In this research, we developed a EVA, EVCL redispersible polymer cement base material applicable as a 3D printing exterior materials, confirmed density and strength characteristics for application as an exterior materials, a flame retardancy test for improving the fire resistance of buildings and confirmed its possibility. From the test result, developed EVCL redispersible polymer cement mortar showed good stability in high temperatures. These high temperature stability is caused by the ethylene-vinyl chloride binding. Thus, this result indicates that it is possible to fire resistant 3D printing interior and exterior finishing materials.

• Journal of the Korea Institute of Building Construction
• /
• v.11 no.2
• /
• pp.127-135
• /
• 2011

In this study, the engineering characteristics of outer wall insulation panels according to type of insulation materials, their combination, and the contents of insulation materials were tested. Vermiculate, ceramic bead, perlite and expanded polystyrene were used as insulation materials. Flexural strength and thermal conductivity depending on the insulation materials used were measured. It was found that the flow of fresh mortar significantly decreased with an increase in the contents of insulation materials. In terms of the effect of insulation materials on thermal conductivity, an increase in insulation materials resulted in a decrease of thermal conductivity. In particular, PL and EPS, when used together, have lower thermal conductivity than other materials. Regarding the flexural strength of the hardened mortar, the strength showed a tendency to gradually decrease according to the increase in contents of insulation materials, compared to that of the plain mortar. In terms of the flexural strength depending on various types of insulation materials and its combination, it was found that the flexural strength of cement mortar containing 3% of vermiculate(V)+ceramic bead(CB)+perlite(PL) was the highest among the specimens tested.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.479.2-479.2
• /
• 2014

자가 세정 및 김서림 방지가 가능한 투명 코팅 소재로써 $TiO_2$ 코팅박막을 제안하였으며, $TiO_2$ 코팅박막은 스퍼터링 방식으로 제작하였다. 낮은 표면 에너지를 갖는 물질을 화학적으로 변형시키고 유리기판 위 텍스쳐링을 형성함으로써, 수분에 대해 완전히 다른 특성을 갖는 표면을 유도하며, 김서림 방지 기능과 자가세정, 그리고 높은 빛 투과 특성으로 스마트 표면 코팅을 구현할 수 있다. $TiO_2$ 자가세정 코팅기술은 설치 후 1년 안에 먼지 및 오염에 따라 최대 40%의 효율 저하가 나타나는 태양전지, 디스플레이 패널 분야에서 매우 중요한 요소로 자리 잡을 것으로 기대되어진다. 본 연구에서는 $TiO_2$ 세라믹 타겟이 부착된 비대칭 마그네트론 스퍼터링 장치를 이용하여 $TiO_2$ 박막을 증착하였으며 증착되어진 $TiO_2$ 박막의 광촉매 특성과 트라이볼로지 특성을 고찰하였다. 광촉매 특성으로는 표면 접촉각 분석을 통하여 고찰하였으며, 트라이볼로지 특성으로는 경도, 잔류응력, 마찰계수, 표면 거칠기 등을 평가하였다. 또한 XRD, FESEM 분석등 구조분석을 통하여 광촉매 특성과 트라이볼로지 특성등과의 연관성을 규명하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.171-171
• /
• 2013

최근에 희토류 이온이 도핑된 형광체를 램프, 플라즈마, 디스플레이 패널, 음극선관, 광전 소자에 응용하기 위한 연구에 많은 노력이 경주되고 있다. 특히 희토류 이온은 4f-껍질에 존재하는 전자의 독특한 성질 때문에 좁은 밴드폭과 강한 발광 특성을 나타내므로 발광 다이오드, 자석, 촉매, 디스플레이 패널용 형광체로 개발되고 있다, 본 연구에서는 고효율의 녹색과 적색 형광체를 개발하기 위하여 모체 결정은 SrSnO3, 활성제 이온은 Eu (유로퓸) 와 Tb (테르븀)을 선택하여 도핑하였다. 합성된 형광체 분말의 회절상을 XRD로 측정한 결과에 의하면, Eu3+와 Tb3+의 함량비에 관계없이 모든 세라믹 분말은 JCPDS #74-1298에 제시된 회절상과 일치하였으며, 주 피크는 $31.3^{\circ}$, $44.9^{\circ}$, $55.8^{\circ}$에서 최대값을 갖는 (110), (200), (211)면에서 발생한 회절 신호이며, 이밖에도 $22.04^{\circ}$, $65.4^{\circ}$, $74.3^{\circ}$에서 약한 회절 피크를 갖는 (100), (220), (013)면의 신호들이 관측되었다. Eu3+ 이온의 함량비가 0.05 mol 인 경우에 (110)과 (211) 피크의 세기가 최대값을 나타내었고, Eu3+의 함량비가 증가함에 따라 두 피크의 세기는 점점 감소하였다. XRD의 데이터를 Scherrer의 식에 대입하여 계산한 결정 입자의 크기는 Eu3+ 이온이 도핑된 경우에는 0 mol에서 최소의 크기를 나타내었고, Tb3+ 이온이 도핑된 경우에 입자의 크기는 0.05 mol에서 최소이었고 0 mol에서 최대값을 보였다. SEM으로 촬영한 표면 형상의 변화를 관측한 결과, Eu3+의 함량비가 0.15 mol인 경우에, 결정 입자의 평균 크기는 400~450nm이며, Tb3+의 함량비가 0.05 mol인 경우에, 결정 입자의 평균 크기는 270~290nm 이었으며, 입자의 형상은 균일하게 분포하는 구형 형태을 보였다. Eu3+와 Tb3+ 이온의 함량비가 점점 증가함에 따라 미립자들이 서로 뭉쳐져서 각각 약 720 nm와 580 nm의 크기를 갖는 큰 입자를 형성하였고, 불규칙적인 분포를 나타내었다. 여기 파장 293 nm에서 Tb3+가 도핑된 SrSnO3:Tb3+ 형광체 분말의 발광 스펙트럼을 측정한 결과에 의하면, Tb3+의 함량비에 관계없이 모든 시료는 주 피크인 550 nm (녹색)와 상대적으로 세기가 약한 500, 590, 630 nm에서 발광 스펙트럼을 나타내었다. 주 피크의 발광 세기는 0.01 mol~0.15 mol에서는 증가 하였고, 더욱 함량비를 증가함에 따라 급격하게 감소하였다. 이 현상은 활성제 이온의 mol 비가 증가함에 따라 이온 사이의 거리가 가까워져서 서로 뭉치는 현상이 주도적으로 작용하여 발광의 세기가 현저히 감소하는 것으로 판단된다. 0.10 mol 일 때 세기가 가장 강한 녹색 형광 신호를 얻었다. 여기 파장 400nm에서 Eu3+가 도핑된 SrSnO3:Eu3+ 형광체 분말의 형광 스펙트럼은 Eu3+의 함량비에 관계없이 590, 619, 696 nm에서 관측되었다. Eu3+의 몰 비가 0.01~0.05 mol 영역에서 619 nm가 주 피크이나, 몰 비가 더욱 증가함에 다라 주 피크의 파장은 590 nm로 이동하였다. 한편, 696 nm의 발광세기는 몰 비가 증가함에 따라 더욱 증가하였다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.3
• /
• pp.330-337
• /
• 2021

3D printing is not only at the fundamental study and small-scale level, but has recently been producing buildings that can be inhabited by people. Buildings require a lot of cost and labor to work on the form work, but if 3D printing is applied to the building, the construction industry is received attention from technologies using 3D printing as it can reduce the construction period and cost. 3D printing technology for buildings can be divided into structural and non-structural materials, of which 3D printing is applied to non-structural materials. Because 3D printing needs to be additive manufacturing, control such as curing speed and workability is needed. Since cement mortar has a large shrinkage due to evaporation of water, cement polymer dispersion is used to improve the hardening speed, workability, and adhesion strength. The addition of polymer dispersion to cement mortar improves the tensile strength and brittleness between the cement hydrate and the polymer film. Cement mortar using polymer materials can be additive manufacturing but it has limited height that can be additive manufacturing due to its high density. When light-weight materials are mixed with polymer cement mortar, the density of polymer cement mortar is lowered and the height of additive manufacturing, so it is essential to use light-weight materials. However, the use of EVA redispersible polymer powder and light-weight materials, additional damage such as cracks in cement mortar can occur at high temperatures such as fires. This study produced a test specimen incorporating light-weight materials and EVA redispersible polymer powder to produce exterior building materials using 3D printing, and examined flame resistance performance through water absorption rate, length change rate, and cone calorimeter test and non-flammable test. From the test result, the test specimen using silica sand and light-weight aggregate showed good flame resistance performance, and if the EVA redispersible polymer powder is applied below 5%, it shows good flame resistance performance.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.4
• /
• pp.53-57
• /
• 2017

The most representative transparent electrode in the modern society is ITO (Indium Tin Oxide). ITO is widely used in general for touch panels and displays due to its high electrical and optical properties. However, in general, mechanical deformation causes deterioration and destruction of device properties because ITO is basically vulnerable to mechanical deformation. Therefore, the in-depth understanding on the stability of ITO film during various mechanical deformations is necessary. In this study, the reliability and mechanical properties ITO sample having different length, width, and area were investigated. The electrical stability was estimated according to electrical resistance change. The stability was dropped as the sample length, and width increased and the sample area decreased. The electrical stability of ITO film was correlated with twisting strain including tensile, compressive and shear stress.

• The Journal of Engineering Geology
• /
• v.33 no.4
• /
• pp.543-553
• /
• 2023

The current status of domestic a agalmatolite mines in South Korea was investigated with a view to establishing a stable supply of agalmatolite and managing its demand. Most mined agalmatolite deposits were formed through hydrothermal alteration of Mesozoic volcanic rocks. The physical characteristics of pyrophyllite, the main constituent mineral of agalmatolite, are as follows: specific gravity 2.65~2.90, hardness 1~2, density 1.60~1.80 g/cm³, refractoriness ≥29, and color white, gray, grayish white, grayish green, yellow, or yellowish green. Among the chemical components of domestic agalmatolite, SiO₂ and Al₂O₃ contents are respectively 58.2~67.2 and 23.1~28.8 wt.% for pyrophyllite, 49.2~72.6 and 16.5~31.0 wt.% for pyrophyllite + dickite, 45.1 and 23.3 wt.% for pyrophyllite + illite, 43.1~82.3 and 11.4~35.8 wt.% for illite, and 37.6~69.0 and 19.6~35.3 wt.% for dickite. Domestic agalmatolite mines are concentrated mainly in the southwest and southeast of the Korean Peninsula, with some occurring in the northeast. Twenty-one mines currently produce agalmatolite in South Korea, with reserves in the order of Jeonnam (45.6%) > Chungbuk (30.8%) > Gyeongnam (13.0%) > Gangwon (4.8%), and Gyeongbuk (4.8%). The top 10 agalmatolite-producing mines are in the order of the Central Resources Mine (37.9%) > Wando Mine (25.6%) > Naju Ceramic Mine (13.4%) > Cheongseok-Sajiwon Mine (5.4%) > Gyeongju Mine (5.0%) > Baekam Mine (5.0%) > Minkyung-Nohwado Mine (3.3%) > Bugok Mine (2.3%) > Jinhae Pylphin Mine (2.2%) > Bohae Mine. Agalmatolite has low thermal conductivity, thermal expansion, thermal deformation, and expansion coefficients, low bulk density, high heat and corrosion resistance, and high sterilization and insecticidal efficiency. Accordingly, it is used in fields such as refractory, ceramic, cement additive, sterilization, and insecticide manufacturing and in filling materials. Its scope of use is expanding to high-tech industries, such as water treatment ceramic membranes, diesel exhaust gas-reduction ceramic filters, glass fibers, and LCD panels.